• Journal of Biosystems Engineering
• /
• v.9 no.2
• /
• pp.48-57
• /
• 1984

To analyze the grain transport velocity, which is valuable for optimizing the separation losses, an oscillating appratus for sieve was designed. The grain transport velocity was measured in each combination of three amplitude levels, three rpm levels and four projection angle levels. To analyze the grain transport velocity theortically, two computer programs were developed. And the results from experiment and theoretical analysis were compared. 1. The grain transport velocity was increased with the projection angle of oscillating sieve. Especially when the projection angle is higher than $45^{\circ}$ the grain transport velocity on the flat-plate was not increased but on the racked surface was increased persistently. 2. The grain transport velocity was increased linearly with the frequency of oscillating motion. The speed of driving link must be higher than 350 rpm at 24mm amplitude, 250 rpm at 36 mm amplitude to transport the grain efficiently. 3. The grain transport velocity was increased with the amplitude of oscillating motion. But if the amplitude was smaller than interval of racks, the grain on the racked surface was not transported, even though the projection angle or the speed of revolutionary link was increased. 4. The transport characteristics of a grain varied with the amplitude and projection angle. Especially in the range of 1.5 < K < 2.3 at $45^{\circ}$ projection angle the transportation of grain was successful and the grain motion consisted of sliding movement (forward, backward) and jumping movement, which is considered recommendable for separating process of a combine sieve. 5. The results from theoretical analysis were approximately in accord with that from experiment.

• Korean Journal of Applied Biomechanics
• /
• v.22 no.3
• /
• pp.295-304
• /
• 2012

This study, through biomechanical analysis, conducts a risk assessment of injury occurrence in ballet dancers while they perform running and jumping movements. The participants were nine female collegiate students majoring in ballet(age: $20.89{\pm}1.17years$; height: $160.89{\pm}7.01cm$; mass: $48.89{\pm}3.26$). Descriptive data were expressed as $mean{\pm}standard$ deviation(SD) for all variables. An independent t-test was conducted to determine how the following variables differed: duration time, position of the center of gravity, angle of the hip, torque of the hip, and muscle activity. All comparisons were made at the p<0.05 significance level. The results show that the jump time was two times longer than the run time in the duration time. The jump length was also longer than the run. The angle of the hip and the torque at the hip were higher in the right. The vastus medialis muscle was most frequently used. These findings demonstrate that participants' jumps may require more biomechanical variables for performance of better and more correct $jet{\acute{e}}$.

• Structural Engineering and Mechanics
• /
• v.74 no.5
• /
• pp.711-722
• /
• 2020

In this study, on-site testing was carried out to investigate the vibration serviceability of a composite steel-bar truss slab with steel girder system. Impulse excitations (heel-drop and jumping) and steady-state motion (walking and running) were performed to capture the primary vibration parameters (natural frequency and damping ratio) and distribution of peak acceleration. The composite floor possesses low frequency (<8.3Hz) and damping ratio (<2.47%). Based on experimental, theoretical, and numerical analyses on fundamental natural frequency, the boundary condition of SCSS (i.e., three edges simply supported and one edge clamped) is deemed more comparable substitutive for the investigated composite floor. Walking and running excitations by one person (single excitation) were considered to evaluate the vibration serviceability of the composite floor. The measured acceleration results show a satisfactory vibration perceptibility. For design convenience and safety, a crest factor β_rp describing the ratio of peak acceleration to root-mean-square acceleration induced from the walking and running excitations is proposed. The comparisons of the modal parameters determined by walking and running tests reveal the interaction effect between the human excitation and the composite floor.

• Physical Therapy Korea
• /
• v.30 no.4
• /
• pp.275-280
• /
• 2023

Background: Although warm-ups before exercise are widely accepted, research on sex differences in improving hamstring flexibility is limited. Differences in the physical and physiological characteristics between males and females may result in different responses to warm-ups. Objects: This study aimed to examine sex differences in the effects of specific warm-up on hamstring flexibility. Methods: This study included 24 young adults with hamstring tightness. The participants performed five maximal knee extensions and flexions at 90° flexion of the hip, and the maximal knee extension angle was measured in real-time using a smartphone clinometer application. Results: The groups did not significantly affect the maximal knee extension angle but showed a significant effect for repetition (p = 0.002) and group-repetition interaction (p = 0.002). Males had no significant change in hamstring flexibility; however, females showed a significant increase in flexibility in the 5^th trial compared with the 1^st trial (p = 0.041). These results demonstrated sex-specific differences in flexibility improvement over time. Conclusion: The findings of this study suggest that specific warm-up can successfully improve hamstring flexibility in females. This may be due to various factors, such as muscle stiffness of the lower extremity, estrogen levels, and temperature sensitivity. In clinical settings, specific warm-up might be helpful for females who participate in sports or activities, such as running or jumping, which require a full range of motion in the hip and knee joints.

• Korean Journal of Applied Biomechanics
• /
• v.18 no.1
• /
• pp.53-62
• /
• 2008

The purpose of this research was to analyze the kinematics of the 205B movement in platform diving. For the experiment, 2 athlete from the national diving team were chosen as the subject and two S -VHS video cameras were used. For this diving players preparing for the olympics participated. It was shown that the mean total took $1.112{\pm}0.12s$. In order to perform better, the divers time must be increased, at take off and rotation must be done high up and the horizontal distance must be shorted to main entrance of the water. To enter the water safely, the jump has to be high, the horizontal speed slow and the vertical speed as fast as possible. At E1 the lower limbs change in speed should decrease and after the rotation begins at E2. At take off, the jump is more important than the rotation for the performance of the dive. At take off, the trunk angular velocity was high, and this was needed to jump high for moment of inertia for rotation because for efficient jumping the upper body has to spread out and increase the height of the center of mass.

• Tunnel and Underground Space
• /
• v.2 no.2
• /
• pp.212-223
• /
• 1992

The distinct element method(DEM) si well suited to the kinematic analysis of blocky rock masses. Two distinctive problems, a rock avalache and tunnel in jointed rock masses, are chosen to apply the DEM which is based on perfectly rigid behaviour of blocks. Investigated for both problems are the effects of the input parameters such as contact stiffnesses, friction coefficient and damping property. Using various types of models of the avalanche and tunne, an extensive parametric study is done to gain experiences in the method, and then to alleviate difficulties in determining parameter values suitable for a given problem. The coefficient of frictio has significant effects on all aspects of avalanche motion(travel distance, velocity and travel time), while the stiffnesses affect the rebounding and jumping motions after collision. The motion predicted by the models having single and mutiple blocks agrees well to the observations reported on the actual avalache. For the tunnel problem, the behaviour of the key block in an example tunnel is compared by testing values of the input parameters. The stability of the tunnel is dependent primarily on the friction coefficient, while the stiffness and damping properties influence the block velocity. The kinematic stability of a tunnel for underground unclear waste repository is analyzed using the joint geometry data(orientation, spacing and persistence) occurred in a tailrace tunnel. Allowing a small deviation to the mean orientation results in different modes of failure of the rock blocks around the tunnel. Of all parameters tested, the most important to the stability of the tunnel in blocky rock masses are the geometry of the blocks generated by mapping the joint and tunnel surfaces in 3-dimensions and also the friction coefficient of the joints particularly for the stability of the side walls.

• Korean Journal of Applied Biomechanics
• /
• v.32 no.1
• /
• pp.24-30
• /
• 2022

Objective: The purpose of this study was to determine the factors of successful and unsuccessful movements through the analysis of kinematics and muscle activity of the Free Aerial Cartwheel on the balance beam. Method: Subjects (Age: 22.8 ± 2.4 yrs., Height: 158.7 ± 5.0 cm, Body mass: 54.1 ± 6.4 kg, Career: 13 ± 2.4 yrs.) who were currently active as female gymnasts participated in the study. They had no history of surgical treatment within 3 months. Subject criteria included more than 10 years of professional experience in college and professional level of gymnastics and the ability to conduct the Free Aerial Cartwheel on the Balance Beam. Each subject performed 10 times of Free Aerial Cartwheel on the balance beam. One successful trial and one unsuccessful trial (failure) among 10 trials were selected for the comparison. Results: It was found that longer time required in case of unsuccessful trial when performing the Free Aerial Cartwheel on the balance beam compared with successful trial. It is expected to be the result of movement in the last landing section (i.e. phase 5). In addition, it was found that the center of gravity of the body descends at a high speed to perform the jump (i.e. phase 2) in order to obtain a sufficient jumping height when the movement is successful while the knee joint is rapidly extended to perform a jump when movement fails. In the single landing section after the jump (i.e. phase 4), if the ankle joint rapidly dorsiflexed after take-off and the hip joint rapidly flexed, so landing was not successful. Conversely, in a successful landing movement, muscle activity of the biceps femoris was greatly activated resulting no shaking in the last landing section (i.e. phase 5). Conclusion: In order to succeed in this movement, it is necessary to perform a strong jump after rapidly descending the center of gravity of the body using the force of the biceps femoris muscle. Further improvement of the skills on the balance beam requires the analysis of the game-like situation with continuous research on kinematic and kinematic analysis of various techniques, jumps, turns, etc.

• Korean Journal of Applied Biomechanics
• /
• v.18 no.3
• /
• pp.61-69
• /
• 2008

The purpose of this study is to examine the success or failure on the balance beam in element group requirements posture which is bending salto side-ward tucked through kinetic analysis. The national team players were participated. The goal was to present training methods to coaches and athletes so as to provide scientifically useful information. The results from this study were summarized as below. When the performance was successful, the features of the body's center of gravity during the side somersault motion showed to spread from the center of the balance beam and the center of the gravity moved to the direction of the body's rotation. In the spring sections - event2 and 3, when the performance was successful, up/down fluctuation became more wider and increased air time. It supported the result that the projecting variable was higher than in failure trial. In addition, the right side hip joint angles and speed, and angular velocity as jumping up for a leap were larger than in failure trial. Those variables showed the optimal conditions for a leap. By increasing the speed of the upper limb from the shoulder and the speed of the shoulder joint angular velocity, the momentum was increased. Especially the right side shoulder joint angular velocity increased dramatically because the right leg was held. As to the side somersault motion, the angular momentum of successful trial with respect to x-axis was bigger than failed trial. It indicated that the increasing angular momentum with respect to x-axis was an important factor in flying motion. Besides, as to side somersault, the appropriate proportion of angular momentum with respect to y-axis and z-axis was a key to successful trails.

• Journal of Korean Physical Therapy Science
• /
• v.25 no.1
• /
• pp.11-19
• /
• 2018

Purpose : The purpose of this study was to examine the effects of ankle kinesio taping on postural control function during exercise in university students. Method : Thirty subjects were randomly allocated to three groups: Y taping group (n=20), I taping group (n=20) and Non-taping group (n=20). All groups underwent the same exercise program including stretching for 30 minutes. The exercise program proceeded in the following order: five minutes of stretching, a 20-minutes exercise program, and additional five 5 minutes of stretching. Of the eight exercise methods suggested by Purcell et al, seven were chosen (lateral shuffle, forward & backward running, agility ladder, figure-of-8, forward jogging while jumping over cones, wall jumps and zigzags); $90^{\circ}$ cuts with lateral shuffle were omitted. The postural control functions was measured participants's perceptions of stability, confidence, and reassurance using methods suggested by Purcell et al,. Result : The confidence was significant difference in I taping group compared to Non taping group. The reassurance was significant difference in Y taping group and I taping group compared to Non taping group. Conclusion : The Kinesio taping increased confidence, and reassurance during exercise in university students. Additional research on Kinesio taping for improving range of motion and agility is need.

• Korean Journal of Applied Biomechanics
• /
• v.22 no.1
• /
• pp.105-111
• /
• 2012

The purpose of this study was to investigate the effect that difference in forefoot of shoe flexibility during the quick lunge from a jump smashing on the lower limbs and the plantar pressure distribution. For this 10 elite badminton players with over 10 years experience and right handed participated. Two kinds of badminton shoes were selected and tested mechanical testing for the forefoot flexibility. Motion analysis, ground reaction forces and plantar pressure distribution were recorded. It was required to conduct lunge movement after jumping smashing as possible as high. Photo sensor was located in 3 meter away from standing position and its height was 40 cm. Subjects were conducted to return original position after touching the sensor as under clear movement as possible as fast. Forefoot stiffness had an effect on shoe peak bending degree and peak bending angular velocity in propulsion phase. Forefoot flexibility had an effect on ankle plantar flexion and knee flexion moment. It appears that joint power on lower limb and peak plantar pressure were not influenced by the flexibility of shoes.