• 한국운동역학회지
• /
• 제18권4호
• /
• pp.161-169
• /
• 2008

이 연구는 성인 남성을 대상으로 계단 너비에 따른 계단 보행의 지지국면 시 하지분절의 역학적 변인을 정량적으로 분석하여, 보다 효과적인 계단의 너비를 제시하고자 실시하였으며, 이를 위해 20대의 남자 대학생 10명이 참여하였다. 계단의 높이는 18cm, 최소폭은 90cm로 동일하나 디딤면의 너비가 각각 26cm, 31cm, 36cm인 세 개의 계단을 사용 하였다. 이때 사용된 계단의 세 번째 디딤면에 지면반력기를 설치하여 지지구간의 하지관절 모멘트를 분석한바 다음과 같은 결론을 얻었다. 상향계단보행에서 발목관절의 굴곡/신전 모멘트변화를 분석한 결과 계단의 너비가 증가 할수록 pull-up 단계의 peak 모멘트가 감소하였으며(p<.05), 무릎관절에서는 굴곡/신전 모멘트를 분석한 결과 계단의 너비가 증가할수록 무릎에 작용하는 신전모멘트가 중지지기에 증가하는 것으로 나타났다(p<.05). 그러나 고관절에서 차이가 없는 것으로 나타났다. 그리고 하향계단보행에서 발목관절의 굴곡/신전 모멘트를 분석한 결과 계단의 너비가 증가할수록 지지기 동안 저측굴곡과 배측굴곡의 차이가 확연히 나타나는 것으로 나타났으며(p<.05), 무릎관절과 고관절에서는 굴곡/신전 모멘트를 분석한 결과 계단의 너비에 따라 신전 모멘트의 차이가 크지 않은 것으로 나타났다.

• The Journal of Korean Physical Therapy
• /
• 제26권2호
• /
• pp.56-61
• /
• 2014

Purpose: The aim of this study was to investigate relationship between the angle of the first metatarsophalangeal joint (1st MPJ) and the dimensions of the abductor hallucis; dorso-plantar (DP) thickness, medio-lateral (ML) width, and cross-sectional area (CSA), in subjects with and without hallux valgus. Methods: Sixty feet, mean (SD) age of 22.5 (2.1) years old, were included in this study (hallux valgus = 30; control = 30). An X-ray device was used for measurement of the angle of the 1st MPJ, and an ultrasound system was used for determination of mean (SD) DP thickness, ML width, and CSA of the abductor hallucis muscle in each foot from three trials. Results: The results showed the DP thickness, ML width, and CSA of the abductor hallucis did not differ significantly between subjects with and without hallux valgus. In addition, the correlations between the angle of the 1st MPJ and DP thickness, ML width, and CSA of the abductor hallucis showed poor correlation (Pearson r=-0.09, -0.20, and -0.18, respectively). Conclusion: Based on these findings, we speculate that morphological changes to the abductor hallucis muscle cannot be representative of the angle of the 1st MPJ, and also cannot be used in differentiation between subjects with and without hallux valgus.

• International Journal of Advanced Culture Technology
• /
• 제3권1호
• /
• pp.145-152
• /
• 2015

The article aims to apply a friction stir spot welding for producing the lap joint between AA5052 aluminum alloy and C11000 copper alloy. The dimension of the materials was 100 mm in length, 30 mm in width and 1.0 mm in thickness. The copper plate was set overlap the aluminum plate by 30 mm. The welding parameter was the rotating speed of 2500-4000 rpm, the pin inserting rate of 2-8 mm/min and the holding time of 6 sec. The mechanical properties test and the microstructure investigation were performed to evaluate the lap joint quality. The summarized results are as follows. The friction stir spot welding could produce effectively the lap joint between AA5052 and C11000 copper. Increase of the rotating speed and holding time directly affected to decrease the tensile shear strength of the lap joint. The optimized welding parameters in this study that indicated the tensile shear strength of 864 N was the rotating speed of 3500 rpm, the pin inserting rate of 6 mm/min and the holding time of 4sec. The experimental results also showed that the hardness of the weld metal was lower than that of the base materials.

• Journal of Welding and Joining
• /
• 제17권6호
• /
• pp.25-31
• /
• 1999

Stainless steel sheets are commonly used for vehicles such as the bus and the train. These are mainly fabricated by spot-welding. By the way, its fatigue strength is lower than base metal due to high stress concentration at the nugget. edge of the spot-welding. By the way, its fatigue strength is lower than base metal due to high stress concentration at the nugget edge of the spot-welding point. Especially, it is influenced by welding conditions as well as geometrical factors of spot welded joint. Therefore, it is not too much to say that structural rigidity and strength of spot-welded structures is decided by fatigue strength of spot welded lap joint. Thus, it is necessary to establish a reasonable and systematic long life design criterion for the spot-welded structure. In this study, numerical stress analysis was performed by using 3-dimensional finite element model on IB-type spot-welded lap joint of 304 stainless steel sheet under tension-shear load. Fatigue tests were also conducted on them having various thickness, joint angle, lapped length, and width of the plate. From the results, it was found that fatigue strength of IB-type spot-welded lap joints was influenced by its geometrical factors, however, could be systematically rearranged by maximum principal stress ({TEX}$σ_{1max}${/TEX}) at the nugget edge of the spot-welding point.

• 대한물리의학회지
• /
• 제14권3호
• /
• pp.21-27
• /
• 2019

PURPOSE: This study examined the changes in the kinematic variables during walking on a downhill ramp according to the shoe heel height. METHODS: The subjects were 10 adult women with no history of musculoskeletal disorders who agreed to participate in the study. Data were collected using a motion analysis system (VICON) consisting of six infrared cameras. The slope was 120 cm in width, 200 cm in length, and 15 in inclination. To confirm the change in gait parameters (stride length, gait speed) and lower extremity joint angle according to the heel heights of the shoes, flat, 5 cm, and 10 cm heel shoes were prepared and walked alternately. RESULTS: As a result, both the stride length and walking speed showed significant differences according to the heel height between flat and 10 cm (p<.05). In the sagittal plane, there was no significant difference in the hip joint and knee joint, but a significant difference was observed in all events in the ankle joint on all heel heights (p<.05). In particular, the heel strike and mid stance events showed significant differences among all height conditions (p<.05). No significant difference was observed in any of the joint angle changes in the frontal plane (p>.05). CONCLUSION: As the shoe heel height increased, the instability increased and efforts to secure the stability were made, leading to a shortened stride length, walking speed, and angle of the ankle joint.

• 한국안전학회지
• /
• 제34권3호
• /
• pp.50-56
• /
• 2019

Precast members have relatively good quality because they are manufactured in an environment suitable for quality control. A typical precast method in which pre-fabricated segments are assembled in the field requires a joint. Although the joint is a small part of the member, it greatly affects the behavior and quality of the structural member. In the previous study of this paper, the flexural strength of a joint, which is generally applied to half-depth precast deck systems, was verified to have higher strength than the design requirement. In addition, the proposed joint has been verified to have higher strength by reinforcing the connecting rebar. However, even if the flexural strength of the joints is sufficient, excessive deflection or lack of fatigue performance is likely to cause cracks in the half-depth precast deck system. In this study, the serviceability of the half-deck precast panel specimens with joints was evaluated and the experimental verification was conducted to evaluate the fatigue performance of the joint without connection rebar. As a result, the serviceability such as deflection and crack width was found to be higher than the design requirement in all the specimens. In the fatigue test, the fatigue effect was insignificant even in the absence of connection rebar.

• 한국강구조학회 논문집
• /
• 제14권3호
• /
• pp.403-411
• /
• 2002

본 논문은 냉간성형 각형강관 T형 접합부의 최대내력과 병형제한치에 대한 두 번째 연구이다. 전회의 실험적 연구로부터, 주관폭에 대한 지관폭의 비($\beta$)가 0.8이상인 T형 접합부는 뚜렷한 최대의 하중을 나타내고 접합부의 파괴모드는 주관 웨브의 좌굴파괴이다. 주관 플랜지 파괴모드의 T형 접합부와 유사하게, 일정한 변형량(주관플랜지에서의 변위)에 대응하는 하중을 T형 접합부의 최대내력으로 정의할 수 있을 것이다. Kato와 Zhao에 의해 수행된 실험을 포함한 실험결과로부터 $10.7{\leq}B/T{\leq}42.3$ 이고 $0.8{\leq}{\beta}{\leq}1.0$ 인 범위의 T형 접합부에 대하여, 최대내력을 정의를 위한 변형제한치는 주관폭의 3% 변형량(3%B)으로 제안하였다. CIDECT의 설계식 및 기존의 제안내력식과 실험결과를 비교하였고, 최종적으로 기둥좌굴에 근거한 내력식을 제안하였다.

• 국제물리치료학회지
• /
• 제7권2호
• /
• pp.1025-1030
• /
• 2016

The purpose of this study was to investigate the effects of combined wedge on the range of motion in ankle and knee joint, ankle eversion moment and knee adduction moment, and center of pressure excursion of foot for genu varus among adult men during gait. This study was carried out with 10 adult men for genu varus in a motion analysis laboratory in J university. The subjects of the experiment were measured above 5cm width between the knees on contact of both medial malleolus of ankle while standing. The width of their knees in neutral position was measured without the inversion or eversion of the subtalar joint by the investigator. The subjects of the experiment were ten who were conducted randomly for standard insole, insole with $10^{\circ}$ lateral on rear foot wedge, insole at $10^{\circ}$lateral on rear foot and $5^{\circ}$ medial on fore foot wedge. Before and after intervention, changes on the range of motion in ankle and knee joint, ankle eversion moment and knee adduction moment, and center of pressure excursion were measured. In order to compare analyses among groups; repeated one-way ANOVA and $Scheff{\acute{e}}$ post hoc test were used. As a result, combined wedge group was significantly decreased compared to control wedge group in terms of knee varus angle in mid-stance(p<.05). Combined wedge group was significantly decreased compared to lateral wedge group in terms of ankle eversion moment in whole stance(p<.05). Combined wedge group was significantly decreased compared to lateral wedge group in terms of knee adduction moment in whole stance(p<.05). Combined wedge group was significantly decreased compared to lateral wedge in terms of center of pressure excursion in whole stance(p<.05). The results of this study suggest that combined wedge for genu varus decreased ankle eversion moment and knee adduction moment upon center of pressure excursion. We hypothesize that combined wedge may also be effective in the protection excessive ankle pronation.

• Journal of Oral Medicine and Pain
• /
• 제48권3호
• /
• pp.106-111
• /
• 2023

Purpose: In this study, we evaluate the potential of the relative ratio of capsular width (RCW) between the affected side (Aff) and non-affected side (Non-aff) in patients with temporomandibular joint (TMJ) arthralgia. We assessed whether RCW may hold greater diagnostic significance than the objective capsular width (CW) reported in previous studies when diagnosing arthralgia using ultrasonography (US). Methods: Forty-nine patients were assessed using US, excluding four patients with bilateral arthralgia. The patients were divided into two groups: 40 with unilateral arthralgia (UA), and nine without arthralgia (NA). We measured CW and masseter muscle thickness using US. Moreover, we employed RCW to analyze the variances between the groups. The numerical rating scale (NRS) and RCW were compared before and after dexamethasone injection in 10 patients who underwent follow-up evaluations. Results: Within the UA group, CW on the Aff was found to be significantly larger compared to the Non-aff (p<0.001). Additionally, RCW in the UA group was greater than that in the NA group (p<0.01). Furthermore, after dexamethasone injection, a reduction in the NRS and RCW values was observed in the 10 patients who were followed up. Conclusions: While previous studies have suggested a link between arthralgia and TMJ effusion, making CW a possible indirect diagnostic indicator for arthralgia, our findings propose that RCW could hold more diagnostic value than objective CW. However, additional studies are required to standardize the protocols for interpreting US results and determining the cutoff value of RCW in diagnosing TMJ arthralgia.

• Journal of Oral Medicine and Pain
• /
• 제17권2호
• /
• pp.63-73
• /
• 1992

This study was performed for the purpose of investigating the relation between width of temporomandibular joint space and craniofacial morphology in patients with CMDs. The subjects utilized here were aged from 16 to 63 years old and 19 male and 46 female. For the study, each patient was taken radiographs by Transcranial and Lateral Cephalographic projection and the films were traced with routine method. The measured items were anterior, superior, posterior joint space and relative condylar position to the deepest part of glenoid fossa in Transcranial film and items related vertical and/or horizontal growth in Cephalogram. The data were processed with SPSS/PC+ package for statistical analysis. The obtained results were as follows : 1. Anterior joint space in affected side were wider than that of unaffected side, but for superior and posterior joint space, the value of unaffected side were more than those of affected side. 2. Superior or posterior joint space of affected side were significantly correlated with items related vertical growth, such as ramus height, Jarabak ratio, FMA. From this, the following cold be proposed, the wider the joint space of superior or posterior aspect of affected side was, the more the patient showed growth pattern of counter clockwise. 3. Superior or posterior joint space of affected side were significantly correlated with items related horizontal growth, such as SNPo, NAPo, APDI and ANB. From this the following could be proposed, the wider the joint space of superior or posterior aspect of affected side was, the more the patient showed anterior displacement of mandible. 4. It would be proposed that the diagnositic value of superior and posterior joint space of affected side in transcranial radiograph was excellent.