• 한국생산제조학회지
• /
• 제4권4호
• /
• pp.50-60
• /
• 1995

Recently advantages joining dissimiliar materials and light weight material techniques have led to increasing use of structural adhesives in the various industries. Stress singulartiy occurs at the interface edges of adhesively bonded dissimilar materials. So it is required to analyze its stress singularity at the interface edges of adhesively bonded joints indissimilar materials. In this paper, the analysis method of stress singularity is studied in detail. Also, effects of the stress singularity at the interface edge of adhesively bonded scarf joints in combinations of dissimilar materials are investigated by using 2-dimensional elastic program of boundary element method. As the results, the strength evaluation method of adhesively bonded dissimilar materials using the stress singularity factor, $\Gamma$,is very useful. The fracture criterion, method of strength evaluation and prediction of fracture strength by the stress singularity factor on the adhesively bonded dissimilar materials are proposed.

• 한국터널지하공간학회 논문집
• /
• 제3권2호
• /
• pp.3-12
• /
• 2001

본 논문은 절리암반 터널의 안정성 해석을 위한 2차원 개별요소모델링방법에 대한 개선방안을 제안하였다. 먼저, 절리군과 터널의 상대방위를 고려하여 터널단면상에서 불연속거동이 가능한 절리군을 구별하는 기준을 제시하였다. 이 기준에 따라 불연속거동이 가능한 절리군은 개별요소(암석블록)의 변이 되도록 하고 그 외 절리군은 암석블록의 탄성특성을 보정하는 방법을 제시하였다. 또한, 주어진 절리의 기하학적 특성에 대해서 절리의 방위편차와 유한길이를 고려한 복잡한 모델과 절리의 평균방위와 무한길이를 고려한 단순한 모델의 특성을 분석하였다. 그 결과, 후자의 모델이 일관성 있는 터널의 국부적 파괴양상과 명료한 암반의 불연속거동을 보여줌으로써 터널설계목적에 적절함을 확인하였다.

• 한국멀티미디어학회논문지
• /
• 제5권2호
• /
• pp.147-157
• /
• 2002

영상 시퀀스에 포함된 잡음은 화질을 열화시키고 중요한 영상의 미세 정보를 훼손시킨다. 또한 잡음은 영상의 복잡성을 증가시키므로 영상의 압축효율을 저하시킨다. 본 논문에서는 특성이 서로 다른 두개의 적응형 잡음제거 필터를 결합적으로 연결하여 잡음을 제거하는 공간결합필터와 시간결합필터를 제시하고, 이 결합필터들을 연결한 IIR필터 구조를 갖는 3차원 잡음제거 필터를 제시한다. 제시된 잡음제거 필터는 영상의 에지와 미세정보를 유지하면서도 평탄한 영상영역에 대해서는 강한 잡음제거를 수행하며 이웃한 프레임 사이에서도 잡음에 의한 시간적인 깜박임을 억제한다. 실험결과 제안된 잡음제거 필터는 기존 방식들에 비하여 객관적 화질뿐만 아니라 주관적인 화질을 크게 향상시킴을 알 수 있었다.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2000년도 하계학술발표회
• /
• pp.228-229
• /
• 2000

Buried channel JET-X CCDs (Joint European X-ray Telescope Charge Coupled Devices: EEV CCD12) with a deep depletion have been analyzed to provide an optimized condition for a charge storage and transfer. A maximum charge capacity has been found for the supplementary narrow channel by considering the potential distribution as a function of a mobile charge. Analysis for the depletion edges of JET-X CCDs have been successfully performed, showing good agreement with the depths estimated from X-ray detection efficiency measurements [1]. (omitted)

• Structural Engineering and Mechanics
• /
• 제53권5호
• /
• pp.1017-1030
• /
• 2015

In this study, the finite element method was used to analyze the distribution of the adhesive shear stresses in the single-lap bonded joint of two plates 2024-T3 aluminum with and without defects. The effects of the adhesive properties (shear modulus, the thickness and the length of the adhesive were highlighted. The results prove that the shear stresses are located on the free edges of the adhesively bonding region, and reach maximum values near the defect, because the concentration of high stress occurs near this area.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1990년도 가을 학술발표회 논문집
• /
• pp.1-6
• /
• 1990

Joints are provided in cement concrete pavements to control transverse and longitudinal cracking that occur due to restrained deformations caused by moisture and temperature variations in the slab. But the construction of joints reduces the load-carrying capacity of the pavement at the joints, and pavements have beem deteriorated by cracks at the slab edges along the joints due to traffic loads. Therefore, it is important to analyze the behavior of joints accurately in the design of cement concrete pavements. In this study, the mechanical behavior of cement concrete pavement slabs is analyzed by the plate-finite element model, and Winkler foundation model is adopted to analyze the subgrades. The load transfer mechanism of joints are composed of dowel action, aggregate interlocking, and tied-key action, and the analytical program is developed using these joint models.

• 대한정형도수물리치료학회지
• /
• 제1권1호
• /
• pp.75-83
• /
• 1995

Traction is the treatment of choice for a small nuclear protrusion. The nucleus is soft and can be influenced by suction. Traction provides a method of improving on recumbency-the only effective treatment before traction was devised. The intention is to achieve rapid reduction by distraction the joint surfaces mechanically-a positive purpose-instead of merely avoiding the compression of the upright posture by putting the patient to bed and leaving him there. Recumbency, usually successful in the end, wastes an endless amount of the patient's time and money. Traction carries the further advantage of enabling the patient to be up and about, attending to his bussiness, during treatment. Traction brings the joint surfaces much farther apart than just lying in bed, a greater centripetal force acts on the protruded part of the nucleus. Traction has three beneficial effects; 1. Suction : a sub-atmospheric pressure induces a centripetal effect on the contents. 2. Distraction : increases the distance between the articular edges. X -rays have shown an increase in width of the joint of 2.5 mm. 3. Ligamentous tightening : the posterior longitudinal ligament tightens which then exerts centipetal force on a central protrusion.

• 콘크리트학회논문집
• /
• 제26권3호
• /
• pp.255-266
• /
• 2014

이 논문은 새로운 수직 접합부와 현장타설 습식 접합부를 가진 T형 프리캐스트 벽체의 내진 성능에 관한 연구이다. 반복하중을 받는 T형 PC 벽체의 하중-변위 관계, 강도, 연성도, 파괴 모드, 그리고 변형 능력에 대해 알아보았다. 실험체 주요 변수는 전단력 전달을 위한 대각 철근의 유무이다. 벽체의 양단에 위치한 길이방향 주철근이 먼저 항복을 하였고 최종 변형은 C형 접합부의 파괴에 의해 결정되었다. 그리고 전단력 전달을 위한 대각 철근은 균열 제어에 효과적인 것으로 나타났다. 단면 해석을 통해 구한 강도와 변형은 실험값과 대체로 일치하였다.

• 한국항공우주학회지
• /
• 제31권1호
• /
• pp.8-17
• /
• 2003

항공기 주구조에서 맞대기중첩연결(Butt Lap Joint) 구조는 저속균열성장 개념의 손상허용설계를 한다. 이러한 연결부 구조는 볼트나 리벳 구멍 가장자리의 부재간 접촉면에서 프레팅에 의한 피로균열이 발생되어 다지점 균열성장 거동을 하는 경우가 많다. 본 연구에서는 초기 모서리균열을 내재한 볼트연결 맞대기중첩연결 구조시편에 프레팅 조건을 달리하여 비행하중스펙트럼 하에서 피로균열 성장거동을 실험적으로 분석하고 잔여강도를 비교하여 프레팅이 균열성장과 손상허용성에 미치는 영향을 고찰하였다. 또한 기존의 응력강도식으로 모서리균열의 성장패턴을 예측하고 실험결과와 비교 분석하였다.

• Advances in aircraft and spacecraft science
• /
• 제11권1호
• /
• pp.83-103
• /
• 2024

Adhesive bonding is currently widely used in many industrial fields, particularly in the aeronautics sector. Despite its advantages over mechanical joints such as riveting and welding, adhesive bonding is mostly used for secondary structures due to its low peel strength; especially if it is simultaneously exposed to temperature and humidity; and often presence of bonding defects. In fact, during joint preparation, several types of defects can be introduced into the adhesive layer such as air bubbles, cavities, or cracks, which induce stress concentrations potentially leading to premature failure. Indeed, the presence of defects in the adhesive joint has a significant effect on adhesive stresses, which emphasizes the need for a good surface treatment. The research in this field is aimed at minimizing the stresses in the adhesive joint at its free edges by geometric modifications of the ovelapping part and/or by changing the nature of the substrates. In this study, the finite element method is used to describe the mechanical behavior of bonded joints. Thus, a three-dimensional model is made to analyze the effect of defects in the adhesive joint at areas of high stress concentrations. The analysis consists of estimating the different stresses in an adhesive joint between two 2024-T3 aluminum plates. Two types of single lap joints(SLJ) were analyzed: a standard SLJ and another modified by removing 0.2 mm of material from the thickness of one plate along the overlap length, taking into account several factors such as the applied load, shape, size and position of the defect. The obtained results clearly show that the presence of a bonding defect significantly affects stresses in the adhesive joint, which become important if the joint is subjected to a higher applied load. On the other hand, the geometric modification made to the plate considerably reduces the various stresses in the adhesive joint even in the presence of a bonding defect.