• Transactions of the Korean hydrogen and new energy society
• /
• v.11 no.1
• /
• pp.11-18
• /
• 2000

In order to investigate the dehydriding properties of the $Mg_2NiH_x$ formed by hydrogen induced mechanical alloying, we performed isothermal thermogravimetry analysis at 453, 463, 473, 483, 493, 503 and 513K for 1 hours. Dehydrogenation kinetics were dependant strongly on the MA conditions which determine the In other words, kinds of synthesized hydrides phases and the crystal microstructures. The MA condition, 66:1 BCR(balls to chips mass ratio), especially 96h milling time, revealed the hydride phases of nano-/ amorphous state and the dehydriding activation energy of $43.4{\pm}3.6kJ/mole$.

• Proceedings of the KIEE Conference
• /
• 2001.07e
• /
• pp.24-26
• /
• 2001

대기환경오염물질인 NO가스의 제거를 위하여 방전관을 채용한 3전극-2갭 방식의 새로운 형태의 오존발생기를 설계 제작하였다. 본 논문에서는 원료가스의 유량, 방전전력 및 오존발생기의 사용 개수 변화에 따른 방전특성과 오존생성특성을 연구 검토하였으며, 오존발생기로부터 생성된 오존을 NO가스에 접촉시켰을 때 NO 제거특성이 우수하여 방전관형 오존발생기가 대기환경개선 설비로 적용 가능함을 확인하였다.

• Proceedings of the KIEE Conference
• /
• 2000.11c
• /
• pp.570-572
• /
• 2000

The characteristics of ozone generation were investigated in accordance with varying the diameter of internal electrode in an ozonizer using RF power source. The characteristics of ozone generation were improved with the diameter of internal electrode increased, but thermal loss was increased. Therefore, it was found that it is inevitable that the cooler has to be installed in an ozonizer which uses RF power source.

• Proceedings of the KIEE Conference
• /
• 1999.07e
• /
• pp.2248-2250
• /
• 1999

In this paper, showering discharge type ozonizer has been designed and manufactured. The ozonizer is equipped with three electrodes(central electrode of screw shape, internal electrode and external electrode) of cylinder shape. This paper describes the following two characteristics: (1) The characteristics of discharge with variation of output voltage of AC H.V source, flux of oxygen supplied gas and discharge voltage. (2) The characteristics of ozone generation by varying flux and discharge power.

• Proceedings of the KIEE Conference
• /
• 1998.07e
• /
• pp.1815-1817
• /
• 1998

In this paper, a superposed discharge type ozonizer(IESDO) has been designed and manufactured. IESDO is equipped with three electrodes(central, internal and external electrodes), and it is composed of two gaps. Ozone is generated by overlapping silent discharge, which is respectively came from two gaps. This paper describes the following characteristics : (1) The characteristics of discharge with variation of output voltage of AC H.V source, quantity of supplied gas and discharge voltage (2) the characteristics of ozone generation with variation of quantity of supplied gas, discharge power, operating number of IESDO.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.444-447
• /
• 2002

The Jig cells are fabricated in the drying room, and consisted of elemental sulfur used as a cathode active material, lithium metal used as a anode material and 1M $LiCF_{3}SO_{3}$ dissolved in TG (Tetraglyme)/DIOX (1,3-Dioxolane) used as a electrolyte. The four kinds of electrolytes with different content of TG and DIOX are prepared. The electrochemical properties of the foregoing electrolytes-based lithium sulfur batteries are analyzed by AC impedance experiments. The conductivity of four different electrolytes is investigated. The conductivity of electrolyte [1M $LiCF_3SO_3$ dissolved in TG/DIOX (50:50, vol.)] is higher than that of other three kinds of electrolytes with different volume ratio (70:30, 30:70) and single solvent (TG).

• Earthquakes and Structures
• /
• v.6 no.3
• /
• pp.237-250
• /
• 2014

This paper experimentally investigates the seismic performance of RC columns retrofitted with Super Reinforcement with Flexibility (SRF), which is a polyester fiber reinforced polymer. A total of three specimens with a scale factor of 1/2 were constructed and tested in order to assess the structural behavior of the retrofitted RC columns. One specimen was a non-seismically designed column without any retrofit, while others were retrofitted with either one or two layers of the polyester belt with urethane as the adhesive. Static cyclic testing with a constant axial load was conducted to assess the seismic performance of the retrofitted RC columns. It is concluded that the SRF retrofitting method increases the strength and ductility of the RC columns and can also impact on the failure mode of the columns.

• Journal of Mechanical Science and Technology
• /
• v.15 no.10
• /
• pp.1380-1385
• /
• 2001

This paper evaluates the fatigue fracture behavior of a chopped strand glass mat/polyester composite both in ai, and sea water, Bending fatigue (R=-1) was performed on dry and wet specimens, that is respectively in air and sea water. Where the pH concentration of sea water was controlled to 6.0,8.2, 10.0 and the wet specimens were immersed in the sea waters for 4 months. Throughout the tests, fatigue cracks both in the dry and wet specimens, tested in the air or sea water, occurred at the beginning of the cycle, followed by either of two regions one decreasing and the other increasing as the crack growth rate increases.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1543-1546
• /
• 1994

Ignitabilility of explosive gas mixture by spark of dry cell in case of short circuit by accident was studied for the purpose of evaluation of intrinsically safe characteristics of dry cell that manufactured in Korea. IEC type spark test apparatus, $21{\pm}2$ Vol% of hydrogen - air mixture, and dry cell that produced in Korea was used for the experiment. The result of this research could be used for design, manufacturing, and using the intrinsically safe electrical apparatus.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.6
• /
• pp.463-469
• /
• 2016

This paper presents a composite camera calibration method to determine thermal degradation of power distribution equipment by combining an infrared (IR) camera and a color camera. A calibration jig was first constructed to match the properties of the two cameras. Our calibration and visualization techniques allow for the display of two images, one from the color camera and the other from the IR camera with different field of views (FOVs), on the screen at the same time. To confirm its validity, several case studies have been developed to analyze thermal deterioration limits of indoor and outdoor power distribution facilities.