• 설비공학논문집
• /
• 제12권1호
• /
• pp.59-66
• /
• 2000

In a previous paper, we have examined the effects of nozzle configuration and jet to jet spacing on the heat transfer of 1 row of circular water jets. In this paper, experiments have been conducted to obtain the effects of nozzle to target plate distances on the heat transfer of 1 row of 3 jets and 1 row of 5 jets. The nozzle configurations are Cone type, Reverse cone type and Vertical circular type. Nozzle to target plate distance H was varied from 16 mm(H/D=2) to 80mm(H/D=10). For fixed value of mass flow rate and nozzle to target plate distance, larger values of average Nusselt number were obtained for the smaller jet to jet spacing. For the array of water jets, the average heat transfer was decreased slightly with increasing nozzle to target plate distance at low jet velocity of $\textrm{V}_{o}$=3 m/s. However, except for $\textrm{V}_{o}$=8 m/s of 1 row of 5 jets, it was increased with increasing nozzle to target plate distance at high jet velocity of $\textrm{V}_{o}$$\geq$6m/s. We proposed to apply the nozzle configuration of maximum average heat transfer to each nozzle to target plate distance for 1 row of 3 jets, and, it was Reverse cone type nozzle for 1 row of 5 jets(Reynolds number$\geq$36000).

• 한국항공우주학회지
• /
• 제34권8호
• /
• pp.8-15
• /
• 2006

고받음각의 NACA23012익형에 대하여 synthetic jet을 이용하여 박리 제어를 수행하였다. 단일 synthetic jet을 이용하여 익형에 발생하는 앞전 박리를 효과적으로 지연시킬 수 있고, 또한 실속 특성을 개선 할 수 있음을 확인하였다. 그때 발생하는 비정상 유동 특성을 파악하였다. 또한, 현실적으로 구현 가능한 jet 속도를 얻기 위하여 multi-array synthetic jet의 특성을 파악하였다. 그리고, 단일 위치에 장착된 synthetic jet을 이용하여 박리를 제어 하였을 경우 익형 윗면에 발생하는 작은 와동을 제거하기 위하여, multi-location synthetic jet을 이용하였다. 작은 와동을 제거하고 안정적인 유동을 확보하기 위하여, 높은 진동수의 synthetic jet을 이용하여 국부적으로 효과적인 박리 제어를 통한 익형 주변의 유동의 전체적 특성을 안정화 시킬 수 있음을 확인하였다. Multi-location synthetic jet의 phase 변화를 이용하여 multi-array/multi-location synthetic jet의 성능 및 특성을 향상 시킬 수 있음을 확인하였다.

• 대한기계학회논문집
• /
• 제18권12호
• /
• pp.3386-3394
• /
• 1994

An experimental study has been performed on the flow over a rotating disk, where the diameter of the disk is 500 mm and the maximum vertical deviation of the upper surface is $50 \mu{m}$ for the whole range of the angular velocity up to 3400 rpm. The flow visualization experiment for the wall jet flow induced by impinging circular jet is carried out using schlieren system and measurements are made by 3-hole and 5-hole pitot tubes. Schlieren photographs show that as the rotating speed increases the wall jet flow becomes more stable and the size of the largest eddies becomes smaller. Measurements for impinging jet flow on the stationary disk verify the accuracy of the present experiment, and those for free rotating disk flow display the existence of transition region from laminar to turbulent flows. Measurements for impinging jet flow on the rotating disk exhibit the interaction between the wall jet and the viscous pumping effect, which explains the decay in size of turbulent eddies illustrated by the schlieren photographs.

• 대한기계학회논문집B
• /
• 제25권6호
• /
• pp.751-757
• /
• 2001

An experimental study of impinging jet-flow structure has been carried out for a fully developed single circular jet impingement cooling on a flat plate, and the effect of the wall thickness at nozzle exit edge is investigated. Impinging jet flow structures have been measured by Laser-Doppler Velocimeter to interpret the heat transfer results presented previously by Yoon et al.(sup)(10) The peaks of heat transfer rate are observed near the nozzle edge owing to the radial acceleration of jet flow when the nozzle locates close to the impingement plate. The growth of the velocity fluctuations in the wall jet flow is induced by the vortices which originate in the jet shear layer, and consequently the radial distribution of local Nusselt numbers has a secondary peak at the certain radial position. As a wall of circular pipe nozzle becomes thicker for small nozzle-to-target distance, the entrainment can be inhibited, consequently, the acceleration of wall jet flow is reduced and the heat transfer rate decreases.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2005년도 창립60주년 기념 추계 학술대회
• /
• pp.81.1-81.1
• /
• 2005

• 대한기계학회논문집
• /
• 제18권5호
• /
• pp.1253-1263
• /
• 1994

The experimental study is carried out to identify the combustion generated noise mechanism in free turbulent jet diffusion flames. Axial mean fluctuating velocities in cold and reacting flow fields were measured using hot-wire anemometer and LDv.The overall sound pressure level and their spectral distribution in far field with and without combustion were also measured in an anechoic chamber. The axial mean velocity is 10-25% faster and turbulent intensities are about 10 to 15% smaller near active reacting zone than those in nonreacting flow fields. And sound pressure level is about 10-20% higher in reacting flow fields. It is also shown that the spectra of the combustion noise has lower frequency characteristics over a broadband spectrum. These results indicate that the combustion noise characteristics in jet diffusion flames are dominated by energy containing large scale eddies and the combusting flow field itself. Scaling laws correlating the gas velocity and heat of combustion show that the acoustic power of the combustion noise is linearly proportional to the 3.8th power of the mean axial velocity rather than 8th power in nonreacting flow fields, and the SPL increases linearly with logarithmic 1/2th power of the heat of combustion.

• 한국화재소방학회논문지
• /
• 제13권2호
• /
• pp.18-25
• /
• 1999

건물 공간에 대한 연기 거동을 해석하기 위한 많은 실험이나 수치해석이 이루어져 왔고 그 중 공간과 공간을 연결해주는 복도 공간에 대한 연기거동을 해석하는 것 또한 매우 중요하다. 본 연구에서는 3차원 비 정렬 격자계, PISO 알고리즘, 부력 Plume 모델을 이용한 Field 모델을 이용하여 복도 공간에 대한 수치해석을 수행하여 얻은 온도장과 유동장 및 변수를 연기 퍼짐 시간과 연충 온도, 천장제트속도로 계산하여 한국기계연구원에서 실험한 결과와 비교하였다. 또한 Hinkley가 제안한 평균 연층 속도와 계산된 연층 속도를 비교하였다. 복도 공간 내에서 Soffit 주위의 유동특성을 파악하고 천장세트의 속도가 복도 향상, 화원으로부터의 거리, 발열량등에 영향을 받는다는 사실을 보여준다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2003년도 제20회 춘계학술대회 논문집
• /
• pp.225-232
• /
• 2003

분리 삼중충돌 제트의 액상 혼합에 대한 실험적 연구결과를 통해 분리 삼중충돌 인젝터의 요소설계시 고려해야 할 기하학적 파라메타와 혼합성능을 고려하는 방법을 제시하였다. 실험은 비반응성인 케로신과 물을 사용하여 수행하였으며, 분사공의 기학적 조건과 분사조건(운동량비)에 따른 국소혼합비 분포를 측정하여 혼합효율 및 혼합특성속도를 산출하였다. 분사공의 각종 기하학적 요소와 운동량비에 따른 혼합효율 및 혼합 특성속도를 비교/분석하고 혼합성능과 연소성능과의 상관관계를 규명하였으며, 혼합의 정도를 향상시키는 설계점과 혼합성능 측면에서의 분리 삼중충돌 인젝터의 최적 설계조건에 대하여 고찰하였다.

• 한국세라믹학회지
• /
• 제43권10호
• /
• pp.646-652
• /
• 2006

Several oxynitride glasses were fabricated by means of adding $Si_3N_4$ powders as nitrogen source to Ca-Al-Si-O-N (CAS) and Mg-Al-Si-O-N (MAS) glass powders, and heat-treated in graphite crucible at 1600$^{\circ}C$ for 1 h. The physical and mechanical properties as well as impact resistance were generally increased and compared with each other. The impact resistance properties of those manufactured glasses were evaluated by DOP (depth of penetration) method which is a way to analyze armor materials. There were two means to be used herein; the copper jet impacted at hyper velocity by exploding K2l5 warhead and tungsten heavy alloy (WHA) impact bar at high velocity by firing in 30 mm solid propellent gun. The impact resistance properties against copper jet were increased and then decreased with increasing nitrogen content, while those against WHA bar were not changed apparently with nitrogen content.

• 한국항공우주학회지
• /
• 제32권6호
• /
• pp.81-86
• /
• 2004

롤 회전하는 유도탄에서 축소-확대 노즐을 지나는 추진 제트와 유도탄과의 각운동량 교환을 통하여 유도탄의 각운동량이 증가하게 되고 이러한 현상을 제트 롤 댐핑이라 한다. 본 연구에서는 제트 롤 댐핑을 각운동량 보존 방정식으로부터 유도하고 근사적인 계산을 통하여 신궁 유도탄의 제트 롤 댐핑의 최대값을 산출하였다. 또한 축대칭 압축성 난류 유동에 대한 수치 해석을 통하여 산출한 제트 롤 댐핑값을 비교하였다.