• Korean Journal of Environmental Agriculture
• /
• v.37 no.1
• /
• pp.57-65
• /
• 2018

BACKGROUND: An analytical method was developed using HPLC-UVD/MS to precisely determine the residue of flusulfamide, a benzenesulfonamide fungicide used to inhibit spore germination. METHODS AND RESULTS: Flusulfamide residue was extracted with acetone from representative samples of five raw products which comprised apple, green pepper, Kimchi cabbage, hulled rice, and soybean. The extract was diluted with large volume of saline water and directly partitioned into dichloromethane to remove polar co-extractives in the aqueous phase. For the hulled rice and soybean samples, n-hexane/acetonitrile partition was additionally employed to remove non-polar lipids. The extract was finally purified by optimized Florisil column chromatography. On an octadecylsilyl column in HPLC, flusulfamide was successfully separated from co-extractives of sample, and sensitively quantitated by ultraviolet absorption at 280 nm with no interference. Accuracy and precision of the proposed method was validated by the recovery experiment on every crop sample fortified with flusulfamide at 3 concentration levels per crop in each triplication. CONCLUSION: Mean recoveries ranged from 82.3 to 98.2% in five representative agricultural commodities. The coefficients of variation were all less than 10%, irrespective of sample types and fortification levels. Limit of quantitation (LOQ) of flusulfamide was 0.02 mg/kg as verified by the recovery experiment. A confirmatory method using LC/MS with selected-ion monitoring technique was also provided to clearly identify the suspected residue.

• Journal of the Korea Concrete Institute
• /
• v.15 no.2
• /
• pp.273-279
• /
• 2003

The purpose of this study is to clarify the effect of the monomer ratio on properties of the polymer-modified mortars using methylmethacrylate-butyl acrylate(MMA/BA) latexes, and to obtain basic data necessary to develop appropriate latexes for cement modifiers. From the test results, we knew that the pore volume of polymer-modified mortars using MMA/BA latexes at bound MMA contents of 60 and 70 percent is 7.5∼75nm and the fine pore volume is increased with an increase in the polymer-cement ratio. The total pore volume of polymer-modified mortars using MMA/BA latexes is linearly reduced with an increase in the bound MMA content and increased in the polymer-cement ratio. In general, the superior compressive strength of polymer-modified mortars using MMA/BA latexes is obtained at a bound MMA content of 70 percent and a polymer-cement ratio of 15%. And, the water absorption and chloride ion penetration depth are greatly affected by the polymer-cement ratio rather than the bound MMA content. The important factors affecting the properties of polymer-modified mortars using MMA/BA latexes polymerized with various monomer ratios are the variations of the pore size distribution with changing bound MMA content and the polymer-cement ratio.

• Korean Journal of Microbiology
• /
• v.50 no.1
• /
• pp.73-83
• /
• 2014

The objective of the this study was to investigate the binding capacity and removal ability of lactic acid bacterial strains obtained from Korean soybean paste for mutagenic heterocyclic amines (HCAs) formed during cooking of protein-rich food at high temperature. Among 19 strains identified by carbohydrate fermentation and 16S rRNA sequencing, the live cell or cell-free culture supernatant of Lactobacillus acidophilus D11, Enterococcus faecium D12, Pediococcus acidilactici D19, L. acidophilus D38, Lactobacillus sakei D44, Enterococcus faecalis D66, and Lactobacillus plantarum D70 inhibited the mutagenesis caused by either 3-amino-1,4-dimethyl-5H-pyrido[4,3-b] indole (Trp-P-1) or 3-amino-1-methyl-5H-pyrido[4,3-b] indole (Trp-P-2) in Salmonella typhimurium TA98 and TA100. The bacterial cells of the isolated strains showed greater binding activity than the pure cell wall, exopolysaccharide, and pepetidoglycan. The carbohydrate moieties of the cell wall or protein molecules on the cell surface have a significant role in binding Trp-P-1 and Trp-P-2, since protease, heating, sodium metaperiodate, or acidic pH treatments significantly (P<0.05) reduced the binding efficacy of the tested bacteria. Addition of metal ions or sodium dodecyl sulfate decreased the binding ability of E. faecium D12, L. acidophilus D38, and E. faecalis D66. Therefore, the binding mechanisms of these strains may consist of ion-exchange and hydrophobic bonds. Especially, the high mutagen binding by L. acidophilus D38 and L. plantarum D70 may reduce the accumulation or absorption of Trp-P-1 and Trp-P-2 in the small intestine via increased excretion of a mutagen-bacteria complex.

• Journal of Korean Society for Atmospheric Environment
• /
• v.17 no.6
• /
• pp.475-485
• /
• 2001

The presence of airborne particles in the earth atmosphere expert important controls on the global climate because of their effects on the radiative balance. However, there are major uncertainties associated with the direct and indirect radiative effects of aerosols. In addition, their physicochemical properties cannot only the decline of air quality but also damage human health. Airborne particles were collected by two different commercial air samples, high volume sampler(for TSP) and low volume sampler(for P $M_{10}$ ) at the campus of Kunsan National University during February to September, 2000. In most cases, TSP and P $M_{10}$ were sampled once a week for the duration of 24 hours from 9:00 a.m. In addition samples were collected more intenisve, when the yellow dust was expected. Each sample was analyzed for pH and major ions concentration (C $l^{[-10]}$ , S $O_4$$^{2-}$, N $O_3$$^{[-10]}$ , N $a^{+}$, N $H_4$$^{+}$, $K^{+}$, $Mg^{2+}$, $Ca^{2+}$) by ion chromatography and atomic absorption spectrophotometry. Acidity (pH) of TSP and P $M_{10}$ ranged from 5.09 to 8.51 and from 6.22 to 7.54, respectively. The concentrations of airborne particles were found to satisfy both the short and long-term air quality standards during the sampling period. If the ratio of ionic concentrations originating from None sea salt(Nss) to sea salt(ss) in aerosol samples was concerned, it was found that the ionic concentrations from marine environment contributed dominantly in total mass concentration in the airborne particles. When seasonal trends were examined, the TSP concentrations in spring were higher than those of other seasons. It may result form frequent occurrences of yellow dust and during the spring season. The concentration ratio of P $M_{10}$ to TSP ranged from 0.78 to 1 during the sampling period. pH in the airborne particle was highest during spring, but the other seasons maintained almost same level. These results suggest that alkaline species in yellow dust can directly neutralize aerosol acidity. During spring season, yellow dust could be a positive factor that can defer the acidification of surface soil and water by neutralizing acidic aerosols in the atmosphere.osphere.

• Korean Journal of Food Science and Technology
• /
• v.30 no.5
• /
• pp.1197-1202
• /
• 1998

Organic acids-eggshell calcium salts were prepared to recycle calcium component from discarded egg shells, and the effects of addition of the salts on dough characteristics of raw noodle and physical properties of cooked noodle were also investigated. Based on Farinograms, calcium malate (CM) affected absorption, stability time, and development time more considerably than calcium citrate (CC). Maximum concentrations of both CM and CC with little influence on dough characteristics were found to be 0.1% and 0.4%, respectively. Addition of calcium salts led to reduce the volume expansion rate of cooked noodle and this was more clearly shown in a sample fortified with CM than CC. As for CC, addition of more than 0.6% resulted in rapid increase in springiness which was in a good agreement with sensory evaluation results. Calcium ion concentration of cooked noodle fortified with 0.4% CC was 48 ppm, equivalent to 86 mg of calcium obtained from 200 g of cooked noodle.

• Membrane Journal
• /
• v.30 no.3
• /
• pp.173-180
• /
• 2020

As the demand for fossil fuels continues to increase worldwide, carbon dioxide (CO₂) concentration in the air has increased over the centuries. The way to reduce CO₂ emissions to the atmosphere, carbon capture and sequestration (CCS) technology have been developed that can be applied to power plants and factories, which are primary emission sources. According to the climate change mitigation policy, direct air capture (DAC) in air, referred to as "negative emission" technology, has a low CO₂ concentration of 0.04%, so it is focused on adsorbent research, unlike conventional CCS technology. In the DAC field, chemical adsorbents using CO₂ absorption, solid absorbents, amine-functionalized materials, and ion exchange resins have been studied. Since the absorbent-based technology requires a high-temperature heat treatment process according to the absorbent regeneration, the membrane-based CO₂ capture system has a great potential Membrane-based system is also expected for indoor CO₂ ventilation systems and immediate CO₂ supply to smart farming systems. CO₂ capture efficiency should be improved through efficient process design and material performance improvement.

• Applied Chemistry for Engineering
• /
• v.31 no.5
• /
• pp.575-580
• /
• 2020

In this study, we simulated an amine regeneration process with heat-stable salts removal unit. We derived the optimal operating conditions considering the flow rate of waste, the removal rate of heat-stable salts, and the loss rate of MDEA (methyl diethanolamine). In the amine regeneration process that absorbs and removes acid gas, heat-stable salt impairs the absorption efficiency of process equipment and amine solution. An ion exchange resin method is to remove heat-stable salts through neutralization by using a strong base solution such as NaOH. The acid gas removal process was established using the Radfrac model, and the equilibrium constant of the reaction was calculated using Gibbs free energy. The removed amine solution is separated and flows to the heat-stable salts remover which is modeled by using the Rstoic model with neutralization reaction. Actual operation data and simulation results were compared and verified, and also a case study was conducted by adjusting the inflow mass of removal unit followed by suggesting optimal conditions.

• Korean Journal of Optics and Photonics
• /
• v.3 no.4
• /
• pp.258-265
• /
• 1992

A low loss optical waveguide of $P_{2}O_{5}-SiO_{2}$on Si substrate is produced by using the chemical vapour deposition method of $SiO_2$ thin films used in Si technology. Propagation loss of the waveguide layer was 1.65 dB/cm as produced and reduced down to 0.1 dB/cm after heat treatment at $1100^{\circ}C$. By using laser lithography and reactive ion etching method $P_{2}O_{5}-SiO_{2}$ waveguide was produced and subsequently annealed at $1100^{\circ}C$.As a result of this annealing the shape of the waveguide core was changed from rectangular to semi-circular form, and the propagation loss was reduced as down to 0.03 dB/cm at 0.6328$\mu$m and 0.04dB/cm at 1.53$\mu$m. We think that the mechanism of the reduction in propagation loss during the heat treatment is the following: 1) The hydrogen bonding in waveguide layer, which causes absorption loss, is dissociated and diffused out. 2) The roughness of the interface and the micro-structure of the waveguide layer is removed. 3) The irregularities in the cross-sectional shape of the waveguide which was induced during the lithographic process were disappeared by flowing of the waveguide core.

• Journal of the Korean Chemical Society
• /
• v.27 no.5
• /
• pp.353-360
• /
• 1983

The adsorption behavior of 8-hydroxyquinoline (8HQ) on Amberlite XAD-4 and-7 resins was investigated by measuring its distribution coefficients under various experimental conditions, such as shaking time, pH and concentration of methanol in the medium. The application of 8HQ-impregnated-XAD resins for the absorption and separation of metal ions was studied. The maximum adsorption of 8HQ on XAD resins was observed in the 30% methanol solution having pH range from 6.0 to 9.0. The impregnation capacities of XAD resins for 8HQ were 3.81${\times}$10-2mmol, 8HQ/g, XAD-4 resins and 2.60${\times}$10-2mmol, 8HQ/g, XAD-7 resin, respectively. The 8HQ-impregnated-XAD resins were stable in pH range from 6.0 to 10.0 and the amount of 8HQ leached from XAD-4 resin by eluting with hydrochloric acid(above 5M) was negligible. The optimum pH range for the adsorption of metal ions on 8HQ-impregnated XAD resin was also 6.0 to 10.0, and the adsorption mole ratio of metal ion to 8HQ were 1 : 2 for Cu(II), Cd(II) and Ni(II), and 1 : 3 for Fe(III) at the above pH range. It was found that the absorbed metal ions on 8HQ-impregnated-XAD resins were recovered quantitatively with 5M HCl and 8HQ-impregnated-XAD-4 resin could be reusable over 5 times without decrease in its impregnation capacity.

• The Korean Journal of Pesticide Science
• /
• v.15 no.4
• /
• pp.389-400
• /
• 2011

A high-performance liquid chromatographic (HPLC) method was developed to determine residues of phenothrin and silafluofen, known as synthetic pyrethroids, in agricultural commodities. Insecticide residues were extracted with acetone from representative samples of four crops which comprised rice, apple, pepper and cabbage. The extract was purified serially by liquid-liquid partition and Florisil column chromatography. For rice and pepper samples, acetonitrile/n-hexane partition was additionally adopted to remove nonpolar interferences. Reversed phase HPLC using an octadecylsilyl column was successfully applied to separate two phenothrin isomers and silafluofen from sample co-extractives. Intact parent compounds were sensitively detected by ultraviolet absorption at 226 nm. Recovery experiment at the quantitation limit validated that the proposed method could apparently determine phenothrin and silafluofen residues at 0.02 and 0.01 mg/kg, respectively. Mean recoveries of phenothrin and silafluofen from four crop samples fortified at three levels in triplicate were in the range of 82.4~109.8% and 83.7~109.8%, respectively. Relative standard deviations of the analytical method were all less than 10%, irrespective of crop types and spiking levels. A selected-ion monitoring (SIM) LC/mass spectrometry (MS) with electrospray ionization was provided to confirm the suspected residue of phenothrin, even though no sufficient ionization of silafluofen was obtained. Both phenothrin and silafluofen could be successfully confirmed by gas chromatography/MS SIM with electron impact at 70 eV. The proposed method is sensitive, repeatable and rapid enough to apply to officially routine inspection of agricultural products.