• Journal of the Korean Electrochemical Society
• /
• v.11 no.4
• /
• pp.313-318
• /
• 2008

The influence of the particle size of platinum(Pt) on the stability and activity was studied. The particle size of platinum was controlled in the range of $3.5{\sim}9\;nm$ by heat treatment of commercial Pt/C and confirmed by XRD and TEM. An accelerated degradation test was performed to evaluate the stability of platinum catalysts. Oxygen reduction reaction was monitored for the measurement of activity. As increasing the Pt particle size, the stability of Pt/C electrode was enhanced and the activity was reduced. It was confirmed that the stability of Pt/C electrode was in inverse proportion to the activity. PtCo/C alloy catalyst was used to improve the activity and stability of large-sized platinum particle. The maximum power density of commercial Pt/C was $507.6\;mV/cm^2$ and PtCo/C alloy catalyst was $585.8\;mV/cm^2$. The decrement of electrochemical surface area showed Pt/C(60%) and PtCo/C alloy catalyst(24%). It was possible to enhance both of stability and activity of catalyst by the combination of particle size control and alloying.

• Tunnel and Underground Space
• /
• v.23 no.5
• /
• pp.413-427
• /
• 2013

Thin Spray-on Liners(TSLs) based on polymer materials have been considered as an alternative to shotcrete and wire mesh in relatively fair rock conditions, and used in mines since 1990s. Nevertheless, Few experimental studies on their mechanical properties necessary for the evaluation of their bearing capacities as a support member have been carried out. In this study, tensile and bond strengths of two kinds of TSLs with different material compositions were measured at the age of 7 days. In addition, two kinds of bending tests proposed by EFNARC (2008) to simulate representative failure mechanisms of TSLs were carried out on the same materials and curing age as in tension and pull-out tests. From the tests, tensile strength of a TSL is shown to increase as its content of polymer is higher. In contrast, its bond strength seems to be in inverse proportion to its polymer content. Especially, the TSL material in which a cementitious component is included with relatively smaller polymer content shows a faster hardening characteristic which results in higher resistance to de-bonding between a TSL and a substrate. As a result, it is shown that the performance of TSLs might be dependent upon its corresponding polymer content.

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.5
• /
• pp.486-496
• /
• 2018

This study was conducted to confirm an effect of span length on bending properties of larch dimensional lumber in the four point bending test. The size of specimen in this study was 38 (width) ${\times}$ 89 (depth) ${\times}$ 3,600 (length) $mm^3$, and average air-dry density and moisture content of the specimens was $543.5kg/m^3$ and 10.5%, respectively. Visually graded No. 1 dimensional lumbers of 248 were divided by two groups to compare modulus of rupture (MOR) and modulus of elasticity (MOE). One group was tested in the four point bending test with span length of 1,650 mm, and other was tested with span length of 3,000 mm. While MOE was not different according to span length in 5% significance level, MOR was different in accordance with span lengths and was in inverse proportion to change of span length. Fifth percentiles of MOR in span length of 1,650 and 3,000 mm were 28.65 and 25.70 MPa, respectively. It was confirmed that the difference between MORs in each case increased as normalized rank increased. This is because of size effect in Weibull weakest link failure theory. Therefore, KS F 2150, in which there is only regulation about span to depth ratio of 15 or more, is needed to be revised to contain a method considering size effect for MOR. From the method, various results of bending test with different size of lumber could be used to determine design value of lumber.

• Journal of IKEEE
• /
• v.22 no.3
• /
• pp.638-644
• /
• 2018

In this paper, we develop a measurement system that uses 3D Scintillator and NaI(TI) Detector to 3-dimensionally identify the location of multiple radiation sources in moving vehicle loads. The radiation measurement system consists of radiation measurement (plastic scintillator), 2-channel Pulse Counter Board, nuclide analysis (NaI(TI) detector) and 1 channel MCA Board. The source locator algorithm calculates the coordinate value of the ratio of the CPS value($1/r^2$) of the source according to the angle(${\theta}$) in inverse proportion to the square of the distance(X, Y) through the SVM classification. The coordinate values are input every predetermined period of the spectrum, and after analyzing the spectrum per unit cycle, the position of the nuclide at the time is calculated by determining whether or not the nuclide is present in the remaining part except for the background area. As a result of the position discrimination test, the error within the international standard of ${\pm}1m$ was shown. Thus, the utility of the proposed system has been demonstrated.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.4
• /
• pp.277-284
• /
• 2018

This paper reports the transparent electrode, which would be applied to transparent displays and smart glasses. Herein, a squared metal mesh with the most widely used copper wire in microwaves is studied for the alternating thin-film-type transparent and conducting indium tin oxide(ITO), with a low conductivity(sheet resistance > $5{\Omega}/sq.$). The electromagnetic performance of a patch antenna with metal mesh is analyzed. This paper presents the results of the optical(OT, optical transparent) and electrical(sheet resistance) characteristics of a squared metal mesh, which is a basic design. To improve the OT, copper wire(w=0.2 mm) is used in fabricating the squared metal mesh and the relationship between the OT and the antenna performance(radiation gain, radiation pattern) was analyzed according to the mesh size(l=1, 2 mm). The measurement results show that the antenna performance and the optical characteristic are in inverse proportion to each other. In real applications, the optical and electrical characteristics, and the costs of production are to be considered.

• Journal of Radiation Protection and Research
• /
• v.32 no.3
• /
• pp.97-104
• /
• 2007

The corelation between the indoor volume and the measured radon concentration has been analyzed by comparing the radon concentration and the indoor volume of apartment rooms in Jeonju City. We also measured the annual exposure dose based on the variation in indoor radon concentration over time. To do this, we took 8 larger rooms and 8 smaller rooms of apartment, respectively, as a sample. The average volume of the larger rooms and that of the smaller rooms were $31.59\;m^3$ and $16.82\;m^3$, respectively. The average radon concentration of the larger rooms and that of the smaller rooms turned out to be $71.73\;Bq/m^3$ and $108.51\;Eq/m^3$, respectively. indicating that indoor volume is in inverse proportion to the radon concentration, i.e., the bigger the ratio of the surface area/volume, the higher the indoor radon concentration. From the measurement of the variation in indoor radon concentration over time fur a single day, the average intraday radon concentration variation was found to be about $46.8\;Bq/m^3$. The highest level of concentration ($114.5\;Bq/m^3$) was measured between 8 and 10 AM and the lowest level of concentration ($67.7\;Bq/m^3$) between 2 and 4 PM. The annual exposure dose turned out to be in the range of 0.3 mSv/yr to 2.16 mSv/yr, showing that the dose in some apartments exceeded 1.3 mSv/yr, the numerical value presented by the United Nations Scientific Committee on the Effects of Atomic Radiation (UNSCEAR).

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.2
• /
• pp.127-140
• /
• 2015

A fault is one of the critical factors that may lead to a possible ground collapse occurring in construction site. A fault core, however, possibly acting as a failure plane in whole fault zone, is composed of fractured rock and gouge nonuniformly distributed and thus can be characterized by its wide range of shear strength which is generally acquired by experimental method for stability analysis. In this study, we performed direct shear test and grain size distribution analysis for 62 fault core samples cropped from 12 different spots located in the vicinity of Kyongju and Ulsan, Korea. As a result, the range of shear strength representing the characteristics of fault cores in the study regions is determined with regard to vertical stress using a regression analysis for experiment data. The weight ratio of gravels in the samples is proportional to the shear strength and that of silt and clay is in inverse proportion to the shear strength. For most samples, the coefficient of determination is over 0.7 despite of inhomogeneity of them and consequently we determined the lower limit and upper limit of the shear strength with regard to the weight ratio by setting the confidence interval of 95%.

• Journal of Korean Ophthalmic Optics Society
• /
• v.11 no.4
• /
• pp.329-335
• /
• 2006

The aim of this study was to evaluate the relation between Asthenopia of near lateral phoria and fusional reserve and also to provide fundamental clinical data. A total of 97 subjects, aged between 17 and 35 years old, who had no strabismus, an eye trouble or whole body disease, were examined nacked visual acuity, corrected visual acuity, corrected diopter, phoria, fusional reserve tests from October of 2005 to July of 2006. We excluded 8 subjects for the following reasons: if they had an amblyopia affecting binocular vision or inaccurate data. After these exclusions, 87 subjects remained. The results were as follow. According to interview results was that in near works, exophoria and esophoria with asthenopia was 59.6%, 64.7%, and 52.6% respectively. The subjects who have exophoria of $0-6{\Delta}$ in the range of normal state was 19.1%. The subjects who have exophoria of $7{\Delta}$ over in the range of abnormal state was 80.9%. The fusional reserve was in inverse proportion to phoria. The fusional reserve was twice over of phoria were 30.3%, and twice under were 69.7%. The asthenopia complain persons were 33.9% with the twice over fusional reserve of phoria. The asthenopia no complain persons were 66.1% with the twice under fusional reserve of phoria. In conclusion, our research has shown conclusively that there is a link between asthenopia of lateral phoria and fusional reserve and we also find that fusional reserve must be examined when we prescribe for a patient who has phoria.

• Journal of Navigation and Port Research
• /
• v.39 no.1
• /
• pp.1-6
• /
• 2015

In this study, with the awareness of the limitations set in the currently operated calculations of holding power and the holding power coefficient of anchors of naval ships due to its simple application of a specific value, various factors that impact the holding power and its coefficient were verified based on existing data analysis of literature research and numerous experiment results from anchor manufacturers, research institutes and academic community in order to overcome the aforementioned limitations. In addition, holding power and holding power coefficient were compared and analyzed by the shape of anchors. As a result, we came to know that the holding power of AC-14 type anchor is stronger than that of ASS type anchor or U.S. Navy Standard type anchor which makes it possible to reduce the weight of the anchor and therefore ease the process of naval shipbuilding. Furthermore, we confirmed the fact that U.S. Navy Standard type anchor does not react sensitively to the weight change of the anchor. Lastly, we found out that Danforth type anchor's holding power coefficient is in inverse proportion to the weight. Moreover, instructions for managing anchor are arranged easily for your information. The results of this study is expected to provide anchor - operating naval crew with a reliable theoretical basis pertaining to an anchor's holding power and its coefficient and contribute much for the safety of their act of anchoring.

• Journal of KIISE:Computer Systems and Theory
• /
• v.33 no.12
• /
• pp.867-879
• /
• 2006

This paper concerns fast and time accurate HW/SW cosimulation for MPSoC(Multi-Processor System-on-chip) architecture where multiple software and/or hardware components exist. It is becoming more and more common to use MPSoC architecture to design complex embedded systems. In cosimulation of such architecture, as the number of the component simulators participating in the cosimulation increases, the time synchronization overhead among simulators increases, thereby resulting in low overall cosimulation performance. Although SystemC cosimulation frameworks show high cosimulation performance, it is in inverse proportion to the number of simulators. In this paper, we extend the novel technique, called virtual synchronization, which boosts cosimulation speed by reducing time synchronization overhead: (1) SystemC simulation is supported seamlessly in the virtual synchronization framework without requiring the modification on SystemC kernel (2) Parallel execution of component simulators with virtual synchronization is supported. We compared the performance and accuracy of the proposed parallel SystemC cosimulation framework with MaxSim, a well-known commercial SystemC cosimulation framework, and the proposed one showed 11 times faster performance for H.263 decoder example, while the accuracy was maintained below 5%.