• Structural Engineering and Mechanics
• /
• 제35권1호
• /
• pp.67-82
• /
• 2010

The beam string structure (BSS) has been widely applied in large span roof structures, while no analytical solutions of BSS were derived for it in the existing literature. In the first part of this paper, calculation formulas of displacement and internal forces were obtained by the Ritz-method for the most commonly used arc-shaped BSS under the vertical uniformly distributed load and the prestressing force. Then, the failure mode of BSS was proposed based on the static equilibrium. On condition the structural stability was reliable, BSS under the uniformly distributed load would fail by tensile strength failure of the string, and the beam remained in the elastic or semi-plastic range. On this basis, the limit load of BSS was given in virtue of the elastic solutions. In order to verify the linear elastic and limit state solutions proposed in this paper, three BSS modal were tested and the corresponding elastoplastic large deformation analysis was performed by the ANSYS program. The proposed failure mode of BSS was proved to be correct, and the analytical results for the linear elastic and limit state were in good agreement with the experimental and FEM results.

• Geomechanics and Engineering
• /
• 제5권5호
• /
• pp.485-497
• /
• 2013

The factor of safety is the most common measure of the safety margin for slopes. When the traditionally defined factor is used in kinematic approach of limit analysis, calculations can become elaborate, and iterative methods have to be used. To avoid this inconvenience, the safety factor was defined in terms of the work rates that are part of the work balance equation used in limit analysis. It was demonstrated for two simple slopes that the safety factors calculated according to the new definition fall close to those calculated using the traditional definition. Statistical analysis was carried out to find out whether, given normal distribution of the strength parameters, the distribution of the safety factor can be approximated with a well-defined probability density function. Knowing this function would make it convenient to calculate the probability of failure. The results indicated that the normal distribution could be used for low internal friction angle (up to about $16^{\circ}$) and the Johnson distribution could be used for larger angles ${\phi}$. The data limited to two simple slopes, however, does not allow assuming these distributions a priori for other slopes.

• 대한한방종양학회지
• /
• 제4권1호
• /
• pp.199-209
• /
• 1998

In order to find antiviral effect against Human immunodeficiency virus(HIV), Herpes simplex virus type I(HSV-1) and II(HSV-2) from herb medicines, publicated 29 paters on anti-viral effect of herbal medicines and a convenient virus-induced cytopathic effect (CEP) inhibition assay was introduced. The major virus on experiment are HIV, Hepatitis B virus and HSV-1,2. Those of other studies showed inhibition of infected virus DNA replication and screening test of herbal medicines. More than 15 extractions were prepared by pure water boiling from herbal medicines, and their toxicity of infected cell and anti-viral activities were evaluated. Among them, the major part of herbal medicines showed cell stability compared with the contrast. Cytotoxic concentration (CC) of the $H_2O$ extracts of Padoo against HIV was <4.0, Hyungbangpaedoksan against HIV was 9.3, Whangyonhaedoktang against HIV-1 and HSV-2 was 15.3. These are high level cytotoxic concentration compared with the contrast. But antiviral effect was unable to figure out for selective $index(SI)=CC_{50}/EC_{50}$. The other herbal medicines were unable to showed potent anti-HIV and anti-HSV activity. The antiviral activation using herbs in this thesis have unlimited objects, to select research object will help to show the direction of antiviral drug development that have less side effect and more excellent efficiency.

• 한국대기환경학회지
• /
• 제15권2호
• /
• pp.121-138
• /
• 1999

This study was carried out to evaluate the performance of a sampling and analytical methodology for the measurement of selected volatile organic compounds (VOCs) in the ambient air. VOCs were determined by the adsorbent tube sampling and automatic thermal desorption coupled with GC/FID and GC/MSD analysis. Target analytes were aromatic VOCs, including BTEX, 1,3,5-and 1,2,4,-trimethylbenzenes(TMBs), and naphthalene. The methodology was investigatedwith a wide range of performance criteria such as repeatability, linearity, lower detection limits, collection efficiency, thermal conditioning, breakthrough volume and calibration methods using internal and external standards. standards. Stability of samples collected on adsorbent tubes during storage was also investigated. In addition, the sampling and analytical method developed during this study was applied to real samples duplicately collected in various indoor and outdoor environments. Precisions for the duplicate samples and distributed volume samples appeared to be well comparable with the performance criteria recommended by USEPA TO-17. The audit accuracy was estimated by inter-lab comparison of both duplicate samples and standard materials between the two independent labs. The overall precision and accuracy of the method were estimated to be within 30% for major aromatic VOCs such as BTEX. This study demonstrated that the adsorbent sampling and thermal desorption method can be reliably applied for the measurement of BTEX in ppb levels frequently occurred in common indoor and ambient environments.

• 한국관개배수논문집
• /
• 제18권2호
• /
• pp.43-53
• /
• 2011

In this study, the internal development of the Saemangeum basic concept of the changes being promoted as a lead construction and agricultural land works(54.2 km) has established a numerical model for the scenario. Inner dike to the construction site to reflect the following conditions to reproduce the numerical model by each areas during construction inner dike where scour expected to perform a numerical analysis for the hydraulic review by areas with possible future changes were to predict. Simulation results showed that numerical simulation results for scour expected frequency of 100 years in flood conditions is simulated with 0.02 m/s~l.27 m/s scour velocity for high-impact factor is considered to be stable. Each start point and end point work area of inner dike reviewed and flow rate of 100 years flood, the velocity distribution in the influx of a large flow rate of 0.02 m/s~1.68 m/s occur during construction inner dike are not being evaluated as a special issue does not occur will be considered according to the method and order of construction inner dike stability review suggests that the future need to be made.

• 한국정보과학회논문지:컴퓨팅의 실제 및 레터
• /
• 제9권3호
• /
• pp.311-321
• /
• 2003

기존 침입차단시스템과 침입탐지시스템과 같은 외곽방어 개념의 보안대책은 전산망 내의 중요 서버를 보호함에 있어서 그 한계를 갖는다. 본 논문에서는 보안 리눅스 운영체제를 구현함에 있어 중요 요구사항으로 TCSEC B1급의 다중등급 보안 기능과 해킹 방어 기능을 정의하고, 이를 시스템 후킹을 통한 리눅스 커널 모듈로 구현하였다 본 구현 시스템의 시험 평가로서 강제적 접근제어 및 해킹 방어 시험, 성능 측정을 실시하여 보안성 및 안정성, 가용성을 입증하였다. 구현된 보안 커널 기반의 리눅스 운영체제는 Setuid 이용 공격, 버퍼 오버플로우 공격, 백도어 설치 공격, 경유지 이용 공격 둥의 해킹을 커널 수준에서 원천적으로 차단하며, 평균 1.18%의 성능 부하율을 나타내어 타 시스템보다 우수하다.

• 조명전기설비학회논문지
• /
• 제29권7호
• /
• pp.22-27
• /
• 2015

In this paper, the problem of voltage unbalancing in series-connected multiple electric double-layer capacitors(EDLCs) is studied. Good understanding of this problem is required in order to increase reliability and stability of an energy storage system comprising EDLCs. Existing methods to settle voltage unbalancing cannot mitigate the problem enough for each cell, since most method have been applied to each module. For equalizing between cells, Zener diode which is one of passive method have been well examined in literature. However, Zener have well not used in balancing due to heating problem. In addition, It is difficult to choose Zener diode fitted rating voltage of EDLC, because of its internal resistance. Thus, we proposed passive balancing using Zener diode by analyzing parasitic element of Zener and EDLC. To experimentally confirm the balancing effect, we compared in two occasions which are with and without passive. As a result, proposed passive balancing circuit mitigated unbalanced voltage gap between EDLCs.

• 한국철도학회논문집
• /
• 제11권1호
• /
• pp.39-44
• /
• 2008

본 연구에서는 실측 주행시험 결과데이터를 바탕으로 윤축 진동과 설계변수간의 관계를 규명하고자 2 자유도계 모델을 구성하였다. 특히 2차 현가장치인 공기스프링의 점탄성 특성을 반영하기 위해 니시무라 공기스프링 모델을 적용하였다. 수치해석 결과 내부 압력 감소 및 보조 공기탱크 체적 증가 시 객차 가속도응답이 감소하는 것을 확인할 수 있었다. 이에 안정성을 헤치지 않는 범위 내에서 현가장치의 강성을 조정해 볼 필요가 있음을 알았다.

• 한국조경학회지
• /
• 제27권3호
• /
• pp.18-31
• /
• 1999

The research deals with external space Seowon(lecture hall) dedicated to education and memorial rises in Sangju area of Choson Dynasty. Characteristics of Seowon as follow; 1. Seowon of Sangju area were built from the middle of 17C to the beginning of 18C. Ideological background of building functioning were grafted into the belief in the three God governing Childbirth, the theory of feng-shui(wind-and water-magic) which is in close connection with the principles of yin and yang, and confucianism and the philosophy of lao-tze and chung-tze. The formation of space were horizontally arrangement and vertical arrangement as the first-learning and then-ancestor shrine of Youngnam provinces. 2. Background and factors of site selection were applied geographical feature, tried to connect owner home town. 3. The shape of path of flow were simple of vertical and curved composition, were continued, were stabilized through composition of human scale's space by reasonable internal. A case of Sangju area, D/H ratio of the front area of buildings and courts was as follows. D/H=1>Hyangkyo> houses on the river>temples>lecture halls. D/H ratio ot the backside areas is as follows. D/H=1>Hyangkyo>houses on the river>lecture halls. 4. Inner garden were planted deciduous than evergreen trees with Lagerstroemia indica. Enclosed dominant trees were planted by Pinus densiflora, Querces seuata.construct GEM strain, and examined for the expression and functional stability in microcosms.

• 연구논문집
• /
• 통권29호
• /
• pp.141-149
• /
• 1999

Brazing of Fe-Cr-Al alloy was carried out at $1200^{\circ}C$ in vacuum furnace using nickel-based filler metals : BNi-5 powder(Ni-Cr-Si-Fe base alloy} and MBF-50 foil (Ni-Cr-Si-B). The effect of boron content on the stability of oxide scale on the brazed joint was investigated by means of cyclic oxidation test performed at $1050^{\circ}C$ and $1200^{\circ}C$. Apparently, the joints brazed with MBF-50 containing boron showed relatively stable oxidation rates compared to boron-free BNi-5 at both temperatures. However, it was considered that the slower weight loss of MBF-50 brazed specimen wasn’t resulted from the low oxidation rate but from the spallation of oxide layer. The oxide layer consisted of thick spinel oxide on the surface and $Al_2 O_3$ internal oxide layer along the interface between mother alloy and braze, the mother alloy was also eroded seriously by the formation of spinel oxides such as $FeCr_2 O_4$ and $NiCr_2 O_4$ on the surface, likely to be induced by the change of oxide forming mechanism due to diffusion of boron from the braze. On the contrary, the joint brazed with BNi-5 showed the good oxidation resistance during the cyclic oxidation test. It seems that the oxidation can be retarded by the formation of stable $Al_2 O_3$ layer at the surface.