• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 가을 학술발표회 논문집
• /
• pp.709-714
• /
• 1997

Recently, the repair materials for defected RC structures are being developed and the performance on repaired RC structures are being studied. This experiment is aimed to evaluate the flexural performance of the RC beams repaired by premix-type materials. The parameters used in this study is the repair materials, the repair length and the treatment of interface. Flexural capacity of repaired RC beams except the polymer-repaired RC beams are similar to that of the control beam. In the flexural capacity, the RC beams treated with chipping show better results than the RC beam without chipping. The various repair lengths of the repaired RC beam are not affected to the flexural capacity.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.33-35
• /
• 2006

We studied the prototypal developments of Plastic Cortex Stimulator (PCS) for stroke patients. The PC sends the stimulation parameters (amplitude, pulse width, cycle, etc.) to the transmitter ZigBee module through serial port. The receiver ZigBee module generates stimulation waveform. The generated output can be controlled by the PC program. Further study can be expanded to portable handset such as PDA using ZigBee. The wireless control of PCS with the handset can help the tele-rehabilitation.

• Structural Engineering and Mechanics
• /
• 제60권4호
• /
• pp.693-705
• /
• 2016

Functionally graded material (FGM) plates can be bonded to the soffit of a beam as a means of retrofitting the RC beam. In such plated beams, tensile forces develop in the bonded plate and these have to be transferred to the original beam via interfacial shear and normal stresses. In this paper, an interfacial stress analysis is presented for simply supported concrete beam bonded with a functionally graded material FGM plate. This new solution is intended for application to beams made of all kinds of materials bonded with a thin plate, while all existing solutions have been developed focusing on the strengthening of reinforced concrete beams, which allowed the omission of certain terms. It is shown that both the normal and shear stresses at the interface are influenced by the material and geometry parameters of the composite beam. This research is helpful for the understanding on mechanical behavior of the interface and design of the FGM-RC hybrid structures.

• Journal of applied mathematics & informatics
• /
• 제29권1_2호
• /
• pp.161-171
• /
• 2011

The convergence rate of a numerical procedure based on Schwarz Alternating Method(SAM) for solving elliptic boundary value problems depends on the selection of the interface conditions applied on the interior boundaries of the overlapping subdomains. It has been observed that the Robin condition (mixed interface condition), controlled by a parameter, can optimize SAM's convergence rate. In [7], one had formulated the multi-parameterized SAM and determined the optimal values of the multi-parameters to produce the best convergence rate for one-dimensional elliptic boundary value problems. However it was not successful for two-dimensional problem. In this paper, we present a new method which utilizes the one-dimensional result to get the optimal convergence rate for the two-dimensional problem.

• 대한기계학회논문집B
• /
• 제20권12호
• /
• pp.3949-3959
• /
• 1996

A new interfacial instability between two vertical fluid layers of different densities is studied. The two layers are flowing between two parallel vertical plates vertically upward or downward, forming counter- or concurrent flows. In order to extend the study to highly-nonlinear regime in future studies, a nonlinear interface evolution equation is derived, and the stability analysis is performed based on the evolution equation. Among the parameters studies are the ratios of the fluid densities and layer thicknesses and the net flow rate.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 1998년도 Proceedings of International Symposium on Remote Sensing
• /
• pp.49-57
• /
• 1998

CO2 transfer velocity is one of the key parameters for CO2 flux estimation at air - sea interface. However, current studies show that significant inconsistency still exists in its estimation when using different models and remotely sensed data sets, which acts as one of the main uncertainties involved in the computation of CO2 exchange coefficient between air - sea interface. In this study, wind data collected from SSM/I and scatterometer onboard ERS-1, in conjunction with operational NOAA/AVHRR, are applied to different models for calculating CO2 exchange coefficient in the world ocean. Their interrelationship and discrepancies inherent with different models and satellite data are analyzed. Finally, the seasonal and inter-annual variation of CO2 exchanges coefficient for different ocean basins are presented and discussed.

• 한국자동차공학회논문집
• /
• 제13권5호
• /
• pp.104-111
• /
• 2005

With increasing use of SUH35/SUH3 dissimilar materials for automotive engine valves, it is required that stress singularities under residual stress on an interface for friction welded dissimilar materials analyzed to establish strength evaluation. The stress singularity $index{\lambda}$ and stress singularities $factor{\Gamma}$ were calculated from using the results of stress analysis to consider residual stress and loads. The stress singularities on variations for shapes and thickness of welded flashes were analyzed and discussed. This paper suggested that the strength evaluation by using the stress singularity factors as fracture parameters, considering the stress singularity on an interface edge of friction welded dissimilar materials will be useful.

• 한국농공학회지
• /
• 제39권1호
• /
• pp.41-47
• /
• 1997

A geographical resource analysis support system (GRASS) was incorporated to an input and output processor for the agricultural nonpoint source pollution (AGNPS) model. The resulting interface system, GIS-AGNPS was a user-friendly, menu-driven system. GIS-AGNPS was developed to automatically process the input and output data from GIS-based data using GRASS and Motif routines. GIS-AGNPS was consisted of GISAGIN which was an input processor for the AGNPS model, GISAGOUT a output processor for the AGNPS and management submodel. The system defines an input data set for AGNPS from attributes of basic and thematic maps. It also provides with editing modes so that users can adjust and detail the values for selected input parameters, if needed. The post-processor at the system displays graphically the outputs from AGNPS, which may he used to identify areas significantly contributing nonpoint source pollution loads.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권6호
• /
• pp.741-749
• /
• 2014

Low power double data rate 2 non-volatile memory (LPDDR2-NVM) has been deemed the standard interface to connect non-volatile memory devices such as phase-change memory (PCM) directly to the main memory bus. However, most of the previous literature does not consider or overlook this standard interface. In this paper, we propose address phase skipping by reforming the way of interfacing with LPDDR2-NVM. To verify effectiveness and functionality, we also develop a system-level prototype that includes our customized LPDDR2-NVM controller and commercial PCM devices. Extensive simulations and measurements demonstrate up to a 3.6% memory access time reduction for commercial PCM devices and a 31.7% reduction with optimistic parameters of the PCM research prototypes in industries.

• Carbon letters
• /
• 제5권2호
• /
• pp.62-67
• /
• 2004

Performance of carbon-carbon composites is known to be influenced by the fibre matrix interactions. The present investigation was undertaken to ascertain the development of microstructure in such composites when carbon fibres possessing different surface energies (T-300, HM-35, P120 and Dialed 1370) and pitch matrices with different characteristics (Coal tar pitch $SP110^{\circ}C$ and mesophase pitch $SP285^{\circ}C$) are used as precursor materials. These composites were subjected to two different heat treatment temperatures of $1000^{\circ}C$ and $2600^{\circ}C$. Quite interesting changes in the crystalline parameters as well as the matrix microstructure are observed and attempt has been made to correlate these observations with the fibre matrix interactions.