• 대한토목학회논문집
• /
• 제36권1호
• /
• pp.39-47
• /
• 2016

노후 콘크리트포장의 가장 일반적인 보수 방법은 복합 구조체 포장구조인 접착식 덧씌우기 방법이 일반적으로 사용되고 있으며, 이와 같은 복합 구조체는 신 구 콘크리트 간 부착력에 따라 공용 중 차량하중, 환경하중 하에서 일체화된 역학적 거동의 확보유무에 따라 장기 공용성 확보에 커다란 영향을 받게 된다. 현재 상용화 되고 있는 접착 덧씌우기 공법들은 우수한 신구 접착력을 확보하기 위하여 다양한 장비를 이용한 경계면 처리 방식과 더불어 재료자체의 접착력을 향상시키고자 폴리머 등의 혼화재료를 사용하고 있다. 그러나 이들 공법들은 현장 적용 시 객관화된 명확한 적용기준 없이 각 공법에서 제시하고 있는 시공장비 및 사용재료에 의존하여 적용 중이며 이러한 각 개별공법의 기준으로 인하여 현장 관리자들의 품질관리에 어려움이 있는 실정이다. 따라서 본 연구에서는 신구 콘크리트 간 부착력 확보에 가장 핵심적인 현장요소인 경계면 처리 방식과 재료의 부착력 확보에 가장 크게 기여하는 폴리머 함량을 변수로 현장시험을 실시함으로써 시공 전 기존 면처리 공정에서의 효과 분석 및 폴리머 혼입률 변화에 따른 부착강도 성능과의 상관성 검토를 통하여 부착강도의 성능을 개선 할 수 있는 현장시공방법을 도출하고자 하였다.

• Elastomers and Composites
• /
• 제49권1호
• /
• pp.43-52
• /
• 2014

브롬화 이소부틸 이소프렌 (BIIR) 고무의 점착성에 미치는 나노점토(Cloisite 20A)의 영향을 조사하였다. 고무내 나노점토의 분산성은 SEM, TEM, XRD으로 분석하였다. 나노점토 충전 및 미충전 고무의 열적안정성은 TGA로 분석하였으며, 충전고무에서 열적안정성을 보였다. 또한 나노점토를 첨가하면 보강효과에 의해 고무의 강도가 증가하였다. 나노점토 첨가로 계면간 분자확산 정도는 감소할 것으로 판단되었지만, 본 연구에서 관찰된 분자확산에 의해 형성된 계면의 두께는 분자사슬간 엄킴현상을 유발하는데 충분하여 계면점착력이 증가하는 것으로 나타났다. 계면점착력 증가현상은 일정한 이상 (8 phr)의 나노점토가 첨가되었을 때 나타났다. 나노점토 첨가에 따른 표면특성의 변화를 조사하기 위해 접촉각 측정을 하였는데 큰 변화는 관찰되지 않았다.

• 한국표면공학회지
• /
• 제46권4호
• /
• pp.145-152
• /
• 2013

The growth behavior of nanocrystalline diamond (NCD) film has been studied for three different substrates, i.e. bare Si wafer, 1 ${\mu}m$ thick W and Ti films deposited on Si wafer by DC sputter. The surface roughness values of the substrates measured by AFM were Si < W < Ti. After ultrasonic seeding treatment using nanometer sized diamond powder, surface roughness remained as Si < W < Ti. The contact angles of the substrates were Si ($56^{\circ}$) > W ($31^{\circ}$) > Ti ($0^{\circ}$). During deposition in the microwave plasma CVD system, NCD particles were formed and evolved to film. For the first 0.5h, the values of NCD particle density were measured as Si < W < Ti. Since the energy barrier for heterogeneous nucleation is proportional to the contact angle of the substrate, the initial nucleus or particle densities are believed to be Si < W < Ti. Meanwhile, the NCD growth rate up to 2 h was W > Si > Ti. In the case of W substrate, NCD particles were coalesced and evolved to the film in the short time of 0.5 h, which could be attributed to the fact that the diffusion of carbon species on W substrate was fast. The slower diffusion of carbon on Si substrate is believed to be the reason for slower film growth than on W substrate. The surface of Ti substrate was observed as a vertically aligned needle shape. The NCD particle formed on the top of a Ti needle should be coalesced with the particle on the nearby needle by carbon diffusion. In this case, the diffusion length is longer than that of Si or W substrate which shows a relatively flat surface. This results in a slow growth rate of NCD on Ti substrate. As deposition time is prolonged, NCD particles grow with carbon species attached from the plasma and coalesce with nearby particles, leaving many voids in NCD/Ti interface. The low adhesion of NCD films on Ti substrate is related to the void structure of NCD/Ti interface.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2018년도 춘계학술대회 논문집
• /
• pp.75-75
• /
• 2018

Commercially pure titanium (CP-Ti) and Ti-6Al-4V alloys have been widely used in implant materials such as dental and orthopedic implants due to their corrosion resistance, biocompatibility, and good mechanical properties. However, surface modification of titanium and titanium alloys is necessary to improve osseointegration between implant surface and bone. Especially, when titanium oxide nanotubes are formed on the surface of titanium alloy, cell adhesion is greatly improved. In addition, plasma electrolytic oxide (PEO) coatings have a good safety for osseointegration and can easily and quickly form coatings of uniform thickness with various pore sizes. Recently, the effects of bone element such as magnesium, zinc, strontium, silicon, and manganese for bone regeneration are researching in dental implant field. The purpose of this study was researched on the surface morphology of PEO-treated Ti-6Al-4V alloy after anodic titanium oxide treatmentusing various instruments. Ti-6Al-4V ELI disks were used as specimens for nanotube formation and PEO-treatment. The solution for the nanotube formation experiment was 1 M $H_3PO_4$ + 0.8 wt. % NaF electrolyte was used. The applied potential was 30V for 1 hours. The PEO treatment was performed after removing the nanotubes by ultrasonics for 10 minutes. The PEO treatment after removal of the nanotubes was carried out in the $Ca(CH_3)_2{\cdot}H_2O+(CH_3COO)_2Mg{\cdot}4H_2O+Mn(CH_3COO)_2{\cdot}4H_2O+Zn(CH_3CO_2)_2Zn{\cdot}2H_2O+Sr(CH_2COO)_2{\cdot}0.5H_2O+C_3H_7CaO_6P$ and $Na_2SiO_3{\cdot}9H_2O$ electrolytes. And the PEO-treatment time and potential were 3 minutes at 280V. The morphology changes of the coatings on Ti-6Al-4V alloy surface were observed using FE-SEM, EDS, XRD, AFM, and scratch tester. The morphology of PEO-treated surface in 5 ion coating solution after nanotube removal showed formation or nano-sized mesh and micro-sized pores.

• 한국토양비료학회지
• /
• 제36권5호
• /
• pp.263-271
• /
• 2003

$CO_2$ 가스 존재여부와 pH가 Pb(II)와 sodium dodecyl sulfonate(SDS, $C_{12}H_{25}SO_3Na$) 흡착에 따른 silca 표면의 특성 변화에 미치는 영향을 contact angle 과 AFM을 이용한 힘 측정을 통하여 살펴보았다. 대기와 접촉하여 $CO_2$가 용해되는 조건에서 Pb와 SDS가 $10^{-4}M$ 씩 들어 있는 혼합용액을 처리하였을 때, fused silica 표면의 contact angle은 $PbCO_3$의 침전 때문에 최대 $46^{\circ}$로 낮았다. 반면에 $N_2$ 개스를 불어넣는 $CO_2$ 부재조건에서는 $PbCO_3$의 침전이 없었기 때문에 contact angle이 최대 $90^{\circ}$로 크게 증가되었다. $CO_2$ 부재조건에서 pH에 따른 contact angle과 AFM에서 측정한 점착력($F_{ad}$) 변화 양상은 $PbOH^+$ 화학종 분포와 유사하였으므로, Pb(II)의 silica 표면 흡착형태는 $PbOH^+$ 로 판단되었다. 한편 contact angle 과 AFM 측정결과 모두 Pb 단독처리에서 소수성을 발현하였다. 이 결과는 현재까지의 알려진 이론으로 설명할 수 없었으며 이를 위하여 원자수준에서의 심도 깊은 연구가 필요하다고 판단되었다.

• The Journal of Advanced Prosthodontics
• /
• 제9권2호
• /
• pp.85-92
• /
• 2017

PURPOSE. The aim of this study was to evaluate the effect of tooth surface pre-treatment steps on shear bond strength, which is essential for understanding the adhesive cementation process. MATERIALS AND METHODS. Shear bond strengths of different cements with various tooth surface treatments (none, etching, priming, or etching and priming) on enamel and dentin of human teeth were measured using the Swiss shear test design. Three adhesives (Permaflo DC, Panavia F 2.0, and Panavia V5) and one self-adhesive cement (Panavia SA plus) were included in this study. The interface of the cement and the tooth surface with the different pre-treatments was analyzed using SEM. pH values of the cements and primers were measured. RESULTS. The highest bond strength values for all cements were achieved with etching and primer on enamel ($25.6{\pm}5.3-32.3{\pm}10.4MPa$). On dentin, etching and priming produced the highest bond strength values for all cements ($8.6{\pm}2.9-11.7{\pm}3.5MPa$) except for Panavia V5, which achieved significantly higher bond strengths when pre-treated with primer only ($15.3{\pm}4.1MPa$). Shear bond strength values were correlated with the micro-retentive surface topography of enamel and the tag length on dentin except for Panavia V5, which revealed the highest bond strength with primer application only without etching, resulting in short but sturdy tags. CONCLUSION. The highest bond strength can be achieved for Panavia F 2.0, Permaflo DC, and Panavia SA plus when the tooth substrate is previously etched and the respective primer is applied. The new cement Panavia V5 displayed low technique-sensitivity and attained significantly higher adhesion of all tested cements to dentin when only primer was applied.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.110-110
• /
• 2015

표면에너지는 계면특성을 지배하는 핵심인자로 디스플레이의 터치 스크린 패널 공정, 이종소재의 접합, 금속의 클래딩 등 실제 산업에 있어서 매우 중요하다. 표면에너지는 코팅과 본딩 이론에 있어서 기본이 되는 물리량으로 표면에너지가 높을수록 코팅 또는 박막 증착시 코팅, 증착이 용이하며 이종소재의 접합도 쉽게 일어난다. 본 연구에서는 플라즈마 표면처리시 산소 분율의 변화에 따른 기판의 표면에너지와 코팅층과 기판의 부착력의 변화에 대해 연구하였다. 연구의 주요 기판으로 ITO, PET 기판을 사용하였고, 표면 에너지 변화를 확인하기 위해 기판을 상온 상압 플라즈마에 노출시켰다. 플라즈마는 아르곤(Ar)의 공급량을 20 LPM으로 고정하고 산소($O_2$)의 공급량을 0 sccm에서 40 sccm 까지 10 sccm 간격으로 변수를 주었다. 표면에너지 값은 기판 위에 형성된 액체의 접촉각을 통해 도출하였다. 표면에너지 측정 액체로 증류수(deionized water)와 디오도메탄(diiodo-methane)을 사용하였다. 표면에너지는 산소분압이 10 sccm에서 최대값인 76 mJ/m2으로 증가한 후 20 sccm까지 유지하다 다시 직선적으로 감소하였다. 기판에 증착된 크롬 박막의 부착력은 스크래치 테스트를 통해 측정하였다. 표면에너지의 증가와 비례하게 부착력은 증가하였고 표면에너지가 감소하는 범위에서는 부착력도 감소하였다. 기판과 코팅층의 부착력 증가 원인 중 하나인 계면 산화물 층의 생성 여부를 알아보기 위해 auger electron spectroscopy (AES) 분석을 진행하였다. AES 분석을 통해 플라즈마 표면처리시 기판과 코팅층의 계면 산화물층의 두께가 표면에너지의 변화와 비례하게 증가하였다가 감소하는 것을 확인하였다. 산소분압이 10 sccm 이었을 경우 산화물층의 두께가 가장 두꺼웠다. 또한 계면의 화학적 결합 상태를 알아보기 위해 X-ray photoelectron spectroscopy (XPS) 분석을 진행하였으며 산소 분율의 변화에 따라 크롬 산화물의 양이 증가하였다 감소하는것을 확인하였다. 이 연구를 통해 산소를 포함한 플라즈마 표면개질이 기판과 코팅층의 부착력 증가에 영향을 끼침을 확인 할 수 있었다. 또한 이를 응용하여 부착력 증가가 필요한 다양한 분야에서도 쉽게 적용시킬 수 있을 것이다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.51.2-51.2
• /
• 2015

Understanding interfacial phenomena has been one of the main research issues not only in semiconductors but only in life sciences. I have been trying to meet the atomic scale surface and interface analysis challenges from semiconductor industries and furthermore to extend the application scope to biomedical areas. Optical imaing has been most widely and successfully used for biomedical imaging but complementary ion beam imaging techniques based on mass spectrometry and ion scattering can provide more detailed molecular specific and nanoscale information In this presentation, I will review the 27 years history of medium energy ion scattering (MEIS) development at KRISS and DGIST for nanoanalysis. A electrostatic MEIS system constructed at KRISS after the FOM, Netherland design had been successfully applied for the gate oxide analysis and quantitative surface analysis. Recenlty, we developed time-of-flight (TOF) MEIS system, for the first time in the world. With TOF-MEIS, we reported quantitative compositional profiling with single atomic layer resolution for 0.5~3 nm CdSe/ZnS conjugated QDs and ultra shallow junctions and FINFET's of As implanted Si. With this new TOF-MEIS nano analysis technique, details of nano-structured materials could be measured quantitatively. Progresses in TOF-MEIS analysis in various nano & bio technology will be discussed. For last 10 years, I have been trying to develop multimodal nanobio imaging techniques for cardiovascular and brain tissues. Firstly, in atherosclerotic plaque imaging, using, coherent anti-stokes raman scattering (CARS) and time-of-flight secondary ion mass spectrometry (TOF-SIMS) multimodal analysis showed that increased cholesterol palmitate may contribute to the formation of a necrotic core by increasing cell death. Secondly, surface plasmon resonance imaging ellipsometry (SPRIE) was developed for cell biointerface imaging of cell adhesion, migration, and infiltration dynamics for HUVEC, CASMC, and T cells. Thirdly, we developed an ambient mass spectrometric imaging system for live cells and tissues. Preliminary results on mouse brain hippocampus and hypotahlamus will be presented. In conclusions, multimodal optical and mass spectrometric imaging privides overall structural and morphological information with complementary molecular specific information, which can be a useful methodology for biomedical studies. Future challenges in optical and mass spectrometric imaging for new biomedical applications will be discussed.

• 한국세라믹학회지
• /
• 제47권3호
• /
• pp.223-231
• /
• 2010

The serious issue of tall building is to ensure the fire-resistance of high strength concrete. The fire resistant finishing method is necessarily essential in order to satisfy the fire resistance time of 3 h required by the law. The fire resistant finishing method is installed by applying a fire resistant material as a method of shotcrete or a fire resistant board to high strength concrete surface. This method can reduce the temperature increase of the reinforcement embedded in high strength concrete at high temperature due to the installation thickness control. This study is interested in identifying the effectiveness of inorganic alumino-silicate compounds including the inorganic admixture such as fly ash and meta-kaolin as the fire resistant finishing materials through the analysis of fire resistance and components properties at high temperature. The study results show that the fire resistant finishing material composed of fly ash and meta-kaolin has the thermal stability of the slight decrease of compressive strength at high temperature. These thermal stability is caused by the ceramic binding capacity induced by alkali activation reaction by the reason of the thermal analysis result not showing the decomposition of calcium hydrate. Inorganic compounds composed of fly ash and meta-kaolin is evaluated to be very effective as the fire resistance material for finishing to protect the concrete substrate by the reason of those simplicity in both application and manufacture. The additional study about the adhesion in the interface with concrete substrate is necessary for the purpose of the practical application.

• 대한치과보철학회지
• /
• 제35권1호
• /
• pp.78-94
• /
• 1997

The purpose of this experiment was to determine the effects of various treatments on denture base resin to metal bond for cobalt-chromium alloy. The metal surface was treated as follows. Group 1 : Sandblasted with $50{\mu}m$ aluminum oxide. Group 2 : Sandblasted with $250{\mu}m$ aluminum oxide. Group 3 : Sandblasted with $250{\mu}m$ aluminum oxide and followed by silicoating. Group 4 : Electrochemically etched. Group 5 : treated with oxidizing solution. Group 6 : Beaded with $200{\mu}m$ retention structure and followed by silicoating. All specimens were applied with 4-META resin and were thermocycled 1000 times at temperature of $5^{\circ}C$ to $55^{\circ}C$. The effects of various surface treatments on the bond strength between 4-META resin and metal interface were measured by using the universal testing machine. All specimens were observed with SEM. The results were as follows 1. The bond strength of 4-META resin were significantly higher to Co-Cr alloy. 2. The bond strength decreased in the following orders : group 6, group 3, groups 1 and 2, group 4, group 5 and there was no statistically significant difference in bond strength among groups 1 and 2.(p>0.05) 3. The bond strength of cobalt-chromium alloy to 4-META resin were not significantly different.(p>0.05) 4. The treated surface of groups 1, 2 and 3 has more fine undercut than that of groups 4 and 5 with SEM. 5. Stable adhesion can be achieved when mechanically roughened metal surface by sandblasting than treating in an electrochemical etching and an oxidizing solution with potassium manganate.