• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.12
• /
• pp.750-758
• /
• 2016

For the channel doping of shallow junction and retrograde well formation in CMOS, indium can be implanted in silicon. The retrograde doping profiles can serve the needs of channel engineering in deep MOS devices for punch-through suppression and threshold voltage control. Indium is heavier element than B, $BF_2$ and Ga ions. It also has low coefficient of diffusion at high temperatures. Indium ions can be cause the erode of wafer surface during the implantation process due to sputtering. For the ultra shallow junction, indium ions can be implanted for p-doping in silicon. UT-MARLOWE and SRIM as Monte carlo ion-implant models have been developed for indium implantation into single crystal and amorphous silicon, respectively. An analytical tool was used to carry out for the annealing process from the extracted simulation data. For the 1D (one-dimensional) and 2D (two-dimensional) diffused profiles, the analytical model is also developed a simulation program with $C^{{+}{+}}$ code. It is very useful to simulate the indium profiles in implanted and annealed silicon autonomously. The fundamental ion-solid interactions and sputtering effects of ion implantation are discussed and explained using SRIM and T-dyn programs. The exact control of indium doping profiles can be suggested as a future technology for the extreme shallow junction in the fabrication process of integrated circuits.

• Journal of Electrical Engineering and information Science
• /
• v.2 no.6
• /
• pp.202-207
• /
• 1997

Design and fabrication issues for an L-band GaAs Monolithic Microwave Integrated Circuit(MMIC) Voltage Controlled Oscillator(VCO) as a component of Personal Communications Systems(PCS) Radio Frequency(RF) transceiver are discussed. An ion-implanted GaAs MESFET tailored toward low current and low noise with 0.5mm gate length and 300mm gate width has been used as an active device, while an FET with the drain shorted to the source has been used as the voltage variable capacitor. The principal design was based on a self-biased FET with capacitive feedback. A tuning range of 140MHz and 58MHz has been obtained by 3V change for a 600mm and a 300mm devices, respectively. The oscillator output power was 6.5dBm wth 14mA DC current supply at 3.6V. The phase noise without any buffer or PLL was 93dB/1Hz at 100KHz offset. Harmonic balance analysis was used for the non-linear simulation after a linear simulation. All layout induced parasitics were incorporated into the simulation with EEFET2 non-linear FET model. The fabricated circuits were measured using a coplanar-type probe for bare chips and test jigs with ceramic packages.

• Korean Journal of Construction Engineering and Management
• /
• v.3 no.2 s.10
• /
• pp.87-98
• /
• 2002

Korea government is making an effort to improve the efficiency in construction industry by introducing CITIS (Contractor integrated Technical Information Service). In order to provide a base for the application of CITIS into the construction industry, this research provides a concept of virtual factory which should be incorporated into CITIS system for the successful collaborative work in the virtual space. It then implements a prototype system through process and data modeling to apply into the road construction projects. The prototype system is tested to verify its efficiency. Finally, lesson learned from these works is provided to advance the current CITIS toward a collaborative virtual factory.

• Journal of the Korea Safety Management & Science
• /
• v.7 no.5
• /
• pp.155-174
• /
• 2005

Parametric life-cycle cost(LCC) models have been integrated with traditional design tools, and used in prior work to demonstrate the rapid solution of holistic, analytical tradeoffs between detailed design variations. During early designs stages there may be competing concepts with dramatic differences. Additionally, detailed information is scarce, and decisions must be models. for a diverse range of concepts, and the lack of detailed information make the integration make the integration of traditional LCC models impractical. This paper explores an approximate method for providing preliminary life-cycle cost. Learning algorithms trained using the known characteristics of existing products be approximated quickly during conceptual design without the overhead of defining new models. Artificial neural networks are trained to generalize on product attributes and life cycle cost date from pre-existing LCC studies. The Product attribute data to quickly obtain and LCC for a new and then an application is provided. In additions, the statistical method, called regression analysis, is suggested to predict the LCC. Tests have shown it is possible to predict the life cycle cost, and the comparison results between a learning LCC model and a regression analysis is also shown

• International Journal of Internet, Broadcasting and Communication
• /
• v.10 no.3
• /
• pp.98-103
• /
• 2018

Globally, medical tourism draws attention as a national growth engine industry, and is actively expanding. Current medical tourism leans towards large hospitals making it difficult to attract new users. Users collect the information for medical tourism through various paths in order to receive medical consultations and customized tour services. To expand medical tourism to small and medium sized hospitals, it is necessary to have customized medical consultations, tours and interpreter services, which are the key elements of medical tourism. This paper suggests services that users can use to match medical consultations and find tours and interpreters they want at the same time. This paper suggests ways to provide integrated services based on the information experienced by users, combining the required items from the perspectives of each user, hospital and guide. To match the content provided by hospitals and guides with experience information from users systematically, this study suggests the convergence plan for a service model that can match the experience information between users and hospitals, between users and guides and between hospitals and guides systematically by operating the data in the universal container.

• Journal of The Korean Astronomical Society
• /
• v.32 no.1
• /
• pp.65-73
• /
• 1999

In this study we present a new improved nonlinear calibration method for vector magnetograms made by the Solar Flare Telescope of BOAO. To identify Fe I 6302.5 line, we have scanned monochromatic images of the line integrated over filter passband, changing the location of the central transmission wavelength of a Lyot filter. Then we obtained a filter-convolved line profile, which is in good agreement with spectral atlas data provided by the Sacramento Peak Solar Observatory. The line profile has been used to derive calibration coefficients of longitudinal and transverse fields, employing the conventional line slope method under the weak field approximation. Our improved nonlinear calibration method has also been used to calculate theoretical Stokes polarization signals with various angles of inclination of magnetic fields. For its numerical test, we have compared input magnetic fields with the calibrated ones, which have been derived from the new improved non-linear method and the conventional method respectively. The numerical test shows that the calibrated fields obtained from the improved method are consistent with the input fields, but not with those from the conventional method. Finally, we applied our new improved method to a dipole model which characterizes a typical field configuration of a single, round sunspot. It is noted that the conventional method remarkably underestimates the transverse field component near the inner penumbra.

• Child Health Nursing Research
• /
• v.8 no.2
• /
• pp.129-140
• /
• 2002

The article reports the process, contents and strategies in the development of community based-heath care management program for high-risk infants and family, which was based on literature review, empirical needs assessment from pilot study. The program was divided into two emphasis areas: (1) identification and home visiting nursing care program, and (2) the construction of self-supporting group. The contents of home visiting nursing care were developed from the pilot study of the direct home visiting to premature infants after discharge. The documentation form for home care was standardized, including the demographic data, birth history, home care services, education and counsels, and visiting schedules. The integrated education protocol was elaborated to enhance the body of knowledge as well as clinical competency in caring high-risk infants and family by the supports of neonatologists, nursing scholar, and clinical specialists. In addition, the process and strategies in developing self-supporting group, consisting the high-risk infants and family, and any significant others were addressed. Emphases were given to the role of public health center and the recycling health care referral system to maximize the growth and development of high-risk infants on the community-base, which in turn, contributing to decrease the postneonatal mortality rate.

• Journal of the Society of Naval Architects of Korea
• /
• v.45 no.2
• /
• pp.109-123
• /
• 2008

The present paper presents the CFD result for a beam wave test case. An ONR tumblehome ship model with bilge keels is used. The beam wave test is for zero forward speed and roll and heave 2DOF with wave slope $a_k=0.156$ and wavelength ${\lambda}=1.12L_{PP}$, with $L_{PP}$ the ship length. The problems is solved numerically with an unsteady Reynolds averaged Navier-Stokes approach. The free surface flow is computed using a single-phase level-set method and the motions in each time step are integrated using a predictor-corrector iteration approach which uses dynamic overset grids moving with relative ship motion. The predicted CFD results for motions and forces are compared with experimental data, showing a reasonable agreement.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.6
• /
• pp.1227-1237
• /
• 1988

A practically useful CAD system for mold design in the plastic injection molding processes has been developed. Even though many efforts have been tried to simulated the injection molding process, this is the first attempt toward an automatic mold design system instead of a manufacturing or a simulation system. In this system the computational routines, the data base for mold design, and the routines for three dimensional modeling are blended together so that the designed mold is obtained as a solid model. For this development, the following problems have been solved. First, the modeling capability of the plastic parts has been implemented by incorporating the modeling routines of a constructive solid geometric modeling system and developing a constant thickness modeling conditions, and that of standard mold bases have been established. Third, the experimental know-how and the empirical formulae have been collected and blended together with the modeling routines of a geometric modeling system to provide the high level commands for designing mold.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.3
• /
• pp.1033-1039
• /
• 2013

Recently, as the product life cycle becomes shorter and customer needs becomes various, it has a great difficulty in managing the product information without the information technology. In this paper, we discuss how to classify numerous BOMs types and propose three categories-Structure-BOM, Display-BOM and Function-BOM for BOMs classification. Based on this result, we design the integrated BOMs management system with ERD(Entity-Relaion-Daiagram) model. This paper presented the methodology for management speed-up and communication innovation in the automotive industry, which incorporated the enterprise-wide product information. The proposed enterprise-BOM design methods also systemized the data related to automotive's principal attributes such as types of levels, options, colors, and consumers' orders. Efficient and flexible development of products can be achieved in the frequently varying environment of products.