• Wind and Structures
• /
• 제36권4호
• /
• pp.263-275
• /
• 2023

As a new kind of construction facility for high rise buildings, the integral steel platform scaffold system (ISPS) consisting of the steel skeleton and suspended scaffold faces high wind during the construction procedure. The lattice structure type and existence of core tubes both make it difficult to estimate the wind load and calculate the wind-induced responses. In this study, an aeroelastic model with a geometry scale ratio of 1:25 based on the ISPS for Shanghai Tower, with the representative square profile, is manufactured and then tested in a wind tunnel. The first mode of the prototype ISPS is a torsional one with a frequency of only 0.68 Hz, and the model survives under extreme wind speed up to 50 m/s. The static wind load and wind vibration factors are derived based on the test result and supplementary finite element analysis, offering a reference for the following ISPS design. The spacer at the bottom of the suspended scaffold is suggested to be long enough to touch the core tube in the initial status to prevent the collision. Besides, aerodynamic wind loads and cross-wind loads are suggested to be included in the structural design of the ISPS.

• 대한토목학회논문집
• /
• 제7권1호
• /
• pp.75-82
• /
• 1987

본(本) 연구(硏究)는 소규모강복범위(小規模降伏範圍)를 벗어나는 대규모강복조건하(大規模降伏條件下)에서 구조안정성(構造安定性)에 관(關)한 중요(重要)한 문제(問題)인 불안정연성파괴(不安定延性破壞)를 평가(評價)할 수 있는 파괴역학인자(破壞力學因子)로서의 J 적분(積分)을 수치해(數値解)로서 구하는데 그 목적(目的)을 두었다. 이를 위해 균열재(龜裂材)의 균열선단요소(龜裂先端要素)로 8절점등방특이요소(節點等方特異要素)를 사용(使用)하고, 균열발생(發生)은 파괴인성(破壞靭性) $J_{IC}$를 초과할 때 일어나도록 하였으며, 그리고 균열성장(成長)의 취급(取級)은 균열개구각(龜裂開口角)을 이용(利用)했다. 본(本) 연구(硏究)에 의해 해석(解析)된 J 적분치(積分値)를 사용(使用)하여 균열재의 균열발생 과 안정성장(安定成長), 불안정(不安定) 발생점(發生點)을 찾은 결과(結果) 다른 연구결과(硏究結果)와 잘 일치(一致)하고 있어 탄소성(彈塑性)을 고려(考慮)한 J 적분치(積分値)가 균열의 안정성장(安定成長) 및 불안정연성파괴(不安定延性破壞) 문제(問題)를 다루는 파괴역학인자(破壞力學因子)로서 직접(直接) 이용(利用)될 수 있음을 보였다.

• 한국산업보건학회지
• /
• 제27권2호
• /
• pp.123-129
• /
• 2017

Objectives: The purpose of this study is to enhance the application of analytical method of polar solvents(alcohols) by GCOTC (gas chromatography open tubular column) through the system suitability test(SST) to estimate the whole chromatographic system performance(integral part). Methods: To perform the SST, carried out repeatability(n=6) as analytical method of polar solvents by GCOTC, got the retention time($t_R$), standard deviation(${\sigma}_{n-1}$) of $t_R$, baseline width($w_b=4{\sigma}_{n-1}$) and calculated dead time($t_m$) by $v_m=d^2{\pi}L(f/4)$ and $v_m=t_m$ x flow rate. Results: In this experiment, obtained the basic data, there were $t_m=2$ min, methanol($t_R=3.569$, ${\sigma}_{n-1}=0.01$, $w_b=0.04$), ethanol ($t_R=3.892$, ${\sigma}_{n-1}=0.004$, $w_b=0.016$), isopropanol($t_R=4.209$, ${\sigma}_{n-1}=0.004$, $w_b=0.016$). By using these data, calculated the corrected retention time($t_R{^{\prime}}$), capacity factor(k), separation factor(${\alpha}$), number of theoretical plate(n) and resolution($R_s$) for SST and got the good results. Conclusions: Through the SST, could reconfirm the whole chromatographic performance system(integral part) for analytical method of polar solvents by GCOTC. Therefore, this analytical method expect to be widely applied at the related areas.

• 대한기계학회논문집A
• /
• 제27권11호
• /
• pp.1986-1996
• /
• 2003

Methodology based on the elastic-plastic fracture mechanics has been widely accepted in predicting the critical crack length(CCL) of pressure tubes of CANDU nuclear plants. A conservative estimate of CCL is obtained by employing the J-resistance curves measured with the specimens satisfying plane strain condition as suggested in the ASTM standard. Due to limited thickness of the pressure tubes the curved compact tension(CT) specimens taken out from tile pressure tube have been used in obtaining J-resistance curves. The curved CT specimen inevitably introduce slant fatigue crack during precracking. Hence, effect of specimen geometry and slant crack on J-resistance curve should be explored. In this study, the difference of J integral values between the standard CT specimens satisfying plane strain condition and the nonstandard curved CT with limited thickness (4.2mm) is estimated using finite element analysis. The fracture resistance curves of Zr-2.5Nb obtained previously by other authors are critically discussed. Various finite element analysis were conducted such as 2D analysis under plane stress and plane strain conditions and 3D analysis for flat CT, curved CT with straight crack and curved CT with slant crack front. J-integral values were determined by local contour integration near the crack tip, which was considered as accurate J-values. J value was also determined from the load versus load line displacement curve and the J estimation equation in the ASTM standard. Discrepancies between the two values were shown and suggestion was made for obtaining accurate J values from the load line displacement curves obtained by the curved CT specimens.

• 전산구조공학
• /
• 제9권2호
• /
• pp.133-142
• /
• 1996

본 논문에서는 혼합모우드형의 공학적 파괴역학을 위한 두가지 방법의 p-version유한요소모델을 사용한 응력확대계수 산정을 목적으로 연구되었다. 두 가지 방법은 COD와 CSD방법에 의한 변위외삽법과 분해법에 기초한 J-적분법이다. 즉, p-version 유한요소해석을 통해 얻어지는 변위장을 균열선에 대해 대칭 및 역대칭 변위로 분리함으로써, 앞에서 언급된 두가지 방법에 의해 모우드-I과 모우드-II 응력확대계수를 결정할 수 있다. 제안된 방법들의 검증을 위한 예제는 인장력을 받는 중앙균열판과 중앙 경사균열판 문제이다. 균열판의 경사각의 변화와 균열길이와 평판 폭의 비에 따른 수치해석결과는 기존 문헌에 있는 이론값과 경험식에 의한 결과와 비교되어 높은 정도를 보여주고 있다 .

• 한국정보통신학회논문지
• /
• 제21권2호
• /
• pp.265-276
• /
• 2017

본 논문에서는 하중 적분 PDC 제어 기법과 T-S 퍼지 외란 관측기를 이용한 강인하면서도 보다 정확한 이동 로봇의 궤도 추적 제어 방법을 제안한다. 하중 적분 PDC 제어 기법은 PDC 제어 기법에 하중 적분 항을 추가함으로써 정상상태 오차를 감소시켜 준다. T-S 퍼지 외란 관측기는 T-S 퍼지 모델로 표현된 비선형 시스템에 대해 외란을 추정하고 상쇄시킬 수 있도록 한다. 따라서, T-S 퍼지 외란 관측기에 기반한 궤도 추적 제어기는 강인한 궤도 추적 성능을 보여준다. 또한, 본 연구에서는 $B\acute{e}zier$ 곡선에 의한 가속도 제한을 갖는 경로 설계 방법에 의해 초기 접근 경로를 설계함으로써, 이동 로봇의 초기 위치가 기준 궤도의 초기 위치와 다를 때 제어 입력이 매우 커지게 되어 실제적으로 사용할 수 없게 되는 문제를 해결한다. 제안된 궤도 추적 제어기의 성능을 시뮬레이션을 통해서 입증하였다.

• Journal of the Korean Wood Science and Technology
• /
• 제45권6호
• /
• pp.836-845
• /
• 2017

Gravimetric method is usually used to evaluate air-dry density, which is governing physical or mechanical properties of wood. Although it had high evaluation accuracy, the method is time consuming process. Thus, this study was conducted to estimate air-dry density of wood with high accuracy by using polychromatic X-ray and digital detector as alternative of gravimetric method. To quantify polychromatic X-ray projection for evaluating air-dry density, Lambert-Beer's law with the integral value of probability function was used. The integral value was used as weighting factor in the law, and it was determined by conducting simple test at various penetration depths and tube voltage. Mass attenuation coefficient (MAC) of wood also calculated by investigating polychromatic X-ray projection according to species, penetration depth and tube voltage. The species had not an effect on change of MAC. Finally, an air-dry density of wood was estimated by applying the integral value, MAC and Lambert-Beer's law to polychromatic X-ray projection. As an example, the relation of the integral value (${\alpha}$) according to penetration depth (t, cm) at tube voltage of 35 kV was ${\alpha}=-0.00091t{\times}0.0184$ while the regression of the MAC (${\mu}$, $cm^2/g$) was ${\mu}=0.5414{\exp}(-0.0734t)$. When calculation of root mean squared error (RMSE) was performed to check the estimation accuracy, RMSE at 35, 45 and 55 kV was 0.010, 0.013 and $0.009g/cm^3$, respectively. However, partial RMSE in relation to air-dry density was varied according to tube voltage. The partial RMSE below air-dry density of $0.41g/cm^3$ was $0.008g/cm^3$ when tube voltage of 35 kV was used. Meanwhile, the partial RMSE above air-dry density of $0.41g/cm^3$ decreased as tube voltage increased. It was conclude that the accuracy of estimation with polychromatic X-ray and digital detector was quite high if the integral value and MAC of wood were determined precisely or a condition of examination was chosen properly. It was seemed that the estimation of air-dry density by using polychromatic X-ray system can supplant the gravimetric method.

• 한국정보통신학회논문지
• /
• 제5권3호
• /
• pp.605-611
• /
• 2001

고수준의 정보 서비스를 제공하기 위해서는 소프트웨어의 고품질화를 추구하여야 한다. 기존에 개발된 품질측정방법들은 모듈내에 포함되어 있는 요인항목들을 서로 다른 관점에서 개별적으로 측정하고있어 통합적인 평가방법이 필요하다. 따라서 본 논문에서는 다수의 측정 방법들을 모두수용 할 수 있는 모델을 제안한다. 제안된 모델은 비율척도들을 선택하고, 러프논리를 이용하여 그들의 중요도를 산출한다. 다음으로 모듈의 품질도를 측정하기 위해서 퍼지적분을 이용하여 척도들의 중요도와 측정값을 종합한다. 마지막으로 척도들과 산출된 품질도의 상관관계를 분석하고, 통계적 방법으로 제안된 모델의 타당성을 보인다.

• International Journal of Aeronautical and Space Sciences
• /
• 제2권2호
• /
• pp.65-72
• /
• 2001

This paper demonstrates an explicit-implicit, finite element analysis for linear as well as nonlinear hygrothermal stress problems. Additional features, such as moisture diffusion equation, crack element and virtual crack extension(VCE) method for evaluating J-integral are implemented in this program. The Linear Elastic Fracture Mechanics(LEFM) Theory is employed to estimate the crack driving force under the transient condition for an existing crack. Pores in materials are assumed to be saturated with moisture in the liquid form at the room temperature, which may vaporize as the temperature increases. The vaporization effects on the crack driving force are also studied. The ideal gas equation is employed to estimate the thermodynamic pressure due to vaporization at each time step after solving basic nodal values. A set of field equations governing the time dependent response of porous media are derived from balance laws based on the mixture theory. Darcy's law is assumed for the fluid flow through the porous media. Perzyna's viscoplastic model incorporating the Von-Mises yield criterion are implemented. The Green-Naghdi stress rate is used for the invariant of stress tensor under superposed rigid body motion. Isotropic elements are used for the spatial discretization and an iterative scheme based on the full Newton-Raphson method is used for solving the nonlinear governing equations.

• 한국구조물진단유지관리공학회 논문집
• /
• 제19권6호
• /
• pp.95-102
• /
• 2015

최근 교량의 노후화에 따른 유지관리 활동이 교통체증, 환경오염, 막대한 비용의 소모로 인하여 어려움을 겪으면서 조립식교량 공법을 이용하는 모듈러 교량 연구가 진행 중이다. 본 연구는 모듈러 교량과 관련된 연구의 일환으로 연결부를 가지는 1방향 모듈러 슬래브를 대상으로 반복하중 재하시 단면2차모멘트의 변화를 분석하고 콘크리트구조기준의 유효단면2차모멘트 식과 비교하였다. 반복하중 재하 실험을 위하여 일체형, 모듈러 실험체 각각 1개씩을 제작하였다. 실험결과, 모듈러 실험체는 일체형 실험체의 비슷한 휨 성능을 가지고 있었으나, 극한 변위는 20% 부족한 모습을 보였다. 반복하중 재하 실험에서는 모듈러 실험체는 일체형 실험체와는 상이한 처짐 거동을 보였고 단면2차모멘트의 변화가 상이하였다. 또한 콘크리트구조기준의 유효단면2차모멘트 계산식은 모듈러 슬래브의 단면2차모멘트를 적절히 반영하지 못하고 있음을 확인하였고, 실험값을 기반으로 하중과 균열모멘트의 비율을 새로운 값인 4.53을 구하였다.