• 한국자동차공학회논문집
• /
• 제20권3호
• /
• pp.7-12
• /
• 2012

Cooled EGR system is widely used to reduce NOx emissions in diesel engine. But when EGR rate was increased, combustion stability was worsened and PM level was increased. So determining optimized control point of EGR rate is important. In order to determine this point, it is important to figure out the effect of EGR system on the exhaust emissions. In this research, NOx and PM emissions were analyzed with various coolant temperature supplied to the EGR cooler at several positions such as downstream of turbocharger, upstream and downstream of DPF. Effects of some variables such as EGR rate, hot / cooled EGR and change of injection timing were estimated. And $CO_2$ emissions were measured at exhaust and intake manifold to calculate EGR rate at each engine operating condition. Also combustion analysis was performed in each engine operating conditions. In the result of this study, there was trade-off between NOx emissions and PM emissions. When EGR rate was increased, combustion pressure was decreased and COV of IMEP was increased.

• 한국자동차공학회논문집
• /
• 제9권4호
• /
• pp.85-91
• /
• 2001

LPG has been well known as a clean alternative fuel for vehicles. As a fundamental study on liquid phase LPG injection (hereafter LPLI) system application to heavy-duty engine, engine output and combustion performance were investigated with various operating conditions using a single cylinder engine equipped with the LPLI system. Experimental results revealed that no problems were occurred in application of the LPG fuel to heavy-duty engine, and that volumetric efficiency and engine output, by 10% approximately, were increased with the LPLI system. It was resulted from the decrease of the intake manifold temperature through liquid phase LPG fuel injection. These results provided an advantage in the decrease of the exhaust gas temperature, in the control of knocking phenomena, spark timing and compression ratio. The LPLI engine could normally operated under $\lambda$=1.5 or EGR 30% condition. The optimized swirl ratio for the heavy duty LPG engine was found around R_s$ = 2.0.

• 대한기계학회논문집
• /
• 제16권9호
• /
• pp.1736-1743
• /
• 1992

본 연구에서는 기화기부착 4행정 4기통 전기점화기관을 사용하여 흡기관내 액 막흐름에 의한 연료의 불균일화가 기관의 연소특성과 배기특성에 미치는 영향을 규명 하는데 궁극적인 목적을 두고 우선, 연소특성을 해석하기 위하여 비교적 고가인 연소 해석 시스템을 개발하는데 1차적인 목적으로 하였으며, 시험제작한 연소해석 시스템으 로 액막흐름의 가시화 및 배기가스 농도측정과 지압선도 해석을 행하여 구조적으로 대 칭인 1번과 4번 실린더의 연소특성과 배기특성을 비교 검토하였다.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.II
• /
• pp.396-404
• /
• 2000

Post harvest processes for rice include drying, storage and processing. Drying has a great effect on the quality of the grain. The existing rice centers are with the ill equipped, especially with drying and storage facilities. The rice harvesting has bully mechanized, a large volume of rice with high moisture content are taken to the rice processing complex(RPC). Three, the need for drying and storage facilities becomes more urgent. At present the daily drying capacity of RPC can't exceed over 40~50 M/T. Therefore new technology and facilities for a high quality and main efficient drying should be introduced one such technology is the continuous flow drying system. This research, aims to test performance efficiency the mixed continuous flow grain dryer was whose daily drying capacity is 100 M/T. The results of the performance tests of the dryer are shown as follows; (1) The temperature distribution of the drying modules were measured by a temperature recorder. The fifth module showed the highest value, followed by the seventh and the third. (2) When the intake air temperature was $55^{circ}C$, the drying rates were 1.7 and 2.6%, wb/pass in the exhaust temperatures of 20 and $22^{circ}C$. And when the intake air temperature was $60^{circ}C$, the drying rates were 1.7 and 2.3%, wb/pass in the exhaust temperatures of 22 and $25^{circ}C$. (3) The average increased rate of cracked grains after the drying process was 0.7% which is below the tolerance limit (2.0%) of the continuous grain dryer.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1997년도 제26회 추계학술대회
• /
• pp.100-109
• /
• 1997

Tappet is the part which consists of valve train system in Over Head Valve type diesel engine. The role of tappet is to open and close the intake/exhaust valve by rotating with cam. There are wear problems like scuffing or pitting in cam/tappet system because of the higher Hertzian contact stress and sliding wear characteristics between cam and tappet. In this paper, to find optimal materials combination in cam/tappet system, wear test and rig test were performed. $Si_3N_4$, chilled cast iron, sintered alloy were selected for tappet materials. As the result of test, it is found that $Si_3N_4$ tappet has the excellent wear properties.

• 한국분무공학회지
• /
• 제9권4호
• /
• pp.77-82
• /
• 2004

This paper describes the improvement of engine cooling system. To improve engine cooling performance, the authors approached in two ways. One is to increase water pump performance, changing of impeller shape and lightening of material were carried out. The second one is cooling efficiency rise, which were investigated with head gasket coolant flow passage optimization with flow visualization technique. The test results show that water pump performance was increased effectively, reduction of pump drive torque, and increase of pump flow-rate and pressure rise. Gasket hole pattern optimization test results represent an optimized head coolant flow which stands cross flow from exhaust to intake port side and small vortex were removed.

• 한국자동차공학회논문집
• /
• 제22권3호
• /
• pp.1-11
• /
• 2014

The aim of this study is to investigate the effect of SCR reactor on the exhaust emissions characteristics in order to develop a urea-SCR aftertreatment system for reducing $NO_x$ emissions. The experiments are conducted by using a flue tube LPG steam boiler with the urea-SCR aftertreatment system. The urea-SCR aftertreatment system utilizes the ammonia converted from 17% aqueous urea solution injected in front of SCR catalyst as a reducing agent for reducing $NO_x$ emissions. The equivalence ratio, urea injection amount, ammonia slip and $NO_x$ conversion efficiency relative to boiler load are applied to discuss the experimental results. In this experiment, the average equivalence ratio is calculated by changing only the fuel consumption rate while the intake air amount is constantly fixed at $25,957.11cm^3/sec$. The average equivalence ratios are 1.38, 1.11, 0.81 and 0.57 when boiler loads are 100, 80, 60 and 40%. The $NO_x$ conversion efficiency is raised with increasing urea injection amount, and $NH_3$ slip is also boosted at the same time. Consequently, the $NO_x$ conversion efficiency relative to boiler load should be examined in combination with urea injection amount and $NH_3$ slip. The results are calculated by 89, 85, 77 and 79% for the boiler loads of 100, 80, 60 and 40%. The appropriate amount of urea injection for the respective boiler load can be not discussed by only $NO_x$ emissions, and should be determined by considering the $NO_x$ conversion efficiency, $NH_3$ slip and reactive activation temperature simultaneously. In this study, the urea amounts of 230, 235, 233 and 231 mg/min are injected at the boiler loads of 100, 80, 60 and 40%, and the final $NH_3$ slips are measured by 8.48, 5.58, 11.97 and 11.34 ppm at the same conditions. THC emission is affected by the SCR reactor under other experimental conditions except 100% engine load, and CO emission at only 40% engine load. The rest of exhaust emissions are not affected by the SCR reactor under all experimental conditions.

• 에너지공학
• /
• 제13권2호
• /
• pp.118-127
• /
• 2004

본 연구는 배기량이 16.7ι인 V8형 터보차져 인터쿨러 직접분사식 디젤기관에서 흡기포트의 선회유동과 연료분사계 및 과급기가 기관성능 및 배출가스특성에 미치는 영향을 실험적으로 고찰하며 성능을 개선하는데 있다. 일반적으로 기관의 출력을 높이기 위하여 과급기 및 인터쿨러를 장착하여 과급공기를 냉각시켜 과급효율을 더욱 높인 TCI디젤기관이 보편화되고 있다 본 연구의 결과로서 흡기포트의 선회비가 2.25인 경우에서 압축비 17.5, re-entrant 8.5$^{\circ}$ 형 연소실, 노즐분공경 $\Phi$0.33*3+$\Phi$0.35*2, 노즐돌출량 3.18mm, 분사시기 BTDC 12$^{\circ}$CA, 과급기 T042(압축기 0.6A/R+46Trim, 터빈 1.0A/R+57Trim)경우가 기관성능 및 NO$_{x}$ 농도의 배출특성을 고려할 때 운전영역에서 가장 우수하여 흡기포트, 분사계 및 과급기에 대한 각 인자를 적정화할 수 있었다.

• 한국자동차공학회논문집
• /
• 제6권6호
• /
• pp.252-258
• /
• 1998

In a SI engine, it is necessary to control fuel quantity in accordance with intake air amount in order to reduce exhaust emission and improve the specific fuel consumption. Generally the map data is used for the vehicles with a SI engine. For the precise control of air-fuel ratio, the real time control method is recommended rather than the control method using map data. In this paper, we developed real time control system using microprocessor and IBM-PC, and applied it to the commercial SI engine. We got good results for air-fuel ratio under the idle condition.

• 한국ITS학회 논문지
• /
• 제7권6호
• /
• pp.48-56
• /
• 2008

본 논문은 대기오염의 주범인 자동차 배기 가스량을 체크하고 차량내의 고장 유 무 진단 시스템 개발이다. 시스템 엔진 정보 추출을 위해 차량 CAN 통신을 이용하고 정보 전송을 위해 ZigBee를 통해 데이터 전송을 한다. 차량 CAN을 위해 차량에서 자체 제공되는 OBD-II 프로토콜을 사용하여 차량의 각종 센서 정보 및 O2 센서 값을 통해 차량 상태 정보 및 배기 가스양을 계산한다. 주행 중인 자동차 엔진 및 내부 고장에 잘 알지 못하는 일반 사용자를 위해 운행 중 실시간 차량의 자가진단 시스템 구축을 목적으로 하고 고장진단 프로토콜 전송을 위한 무선통신 인터페이스로 저 전력 저비용 ZigBee 통신 인터페이스를 구축한다. 자동차 그리고 진단 시스템의 통신을 위해 ZigBee 시스템을 통하여 효율적 저비용 통신 인터페이스를 구성하여 차량내의 엔진 및 각종 센서 정보 네트워크를 지원한다. 차량에서 전송되어 온 각종 센서정보는 ZigBee 기반을 통해 ZigBee 메인 컨트를 시스템에 전송된다. 차량에 이상이 생겼을 때 트러블 코드를 저장하고 자동차가 정비소에 갔을 때 정확한 판단을 하여 신속하게 처리 할 수 있게 해 주며 자동차에 대해서 잘 알지 못하는 운전자에게 정확한 정보를 제공한다. 또한 멀티미디어 시스템 기능을 추가하고 주행 중 무선 인터넷이 가능하도록 시스템을 확장한다. 마지막으로 주행 중 차량 자가진단을 위해 저 전력 임베디드 리눅스 시스템을 구축하고 실 실험을 통하여 구현하고 검증한다.