• Journal of the Korean Society for Advanced Composite Structures
• /
• v.3 no.4
• /
• pp.27-37
• /
• 2012

The construction of a moment connection for a rectangular hollow section (RHS) column and a H-shaped beam is difficult because the RHS is a closed section. When a inner diaphragm is used for such a connection, in general, it is installed after cutting the HSS columns, which results in increased construction work. This paper suggests a new fabrication method to overcome such problems: An inner diaphragm is welded to inside a C-shaped section first, and then a column is fabricated by welding two C-shaped sections. This fabrication method is superior to a classic method in terms of constructibility. An experimental and a numerical study using Ansys 9.0 were performed in order to compare the strength of connections with respect to the presence of concrete, the corner shape of diaphragm, and the axis of loading. The experimental results including initial stiffness and ultimate loads are reported and the analytical results including load transfer mechanism, degree of stress concentration, and strain distribution are also reported.

• Composites Research
• /
• v.26 no.6
• /
• pp.380-385
• /
• 2013

Characteristics of delamination factor and surface roughness by drilling condition for glass fiber reinforced plastic (GFRP) composites were investigated in this paper. An expression to quantify the delamination factor was induced by using image pixels of the entry and the experimental drilling was accomplished by fabricating several GFRP specimens in condition of minimizing the effect of vibration and heat. A method for measuring 6 points average surface roughness was applied to acquire the more reliable roughness values. The experimental results showed that the delamination factor was decreased as the feed rate was increased and it was also slightly decreased as the cutting speed was increased. Also, it was investigated that the surface roughness at inner surface of drilled holes was increased as the feed rate was increased, whereas the roughness values were not affected by the cutting speed variation.

• Korean Journal of Veterinary Service
• /
• v.23 no.4
• /
• pp.361-366
• /
• 2000

The growth of bacteria on the surface of the meat was monitored to investigate the relationships between microbiological quality and some environmental factors such as the chilling temperature, alcohol spraying, and transport in slaughter process of pigs. The temperature changes of the surface and inner part of pork carcass were monitored with GreenTrack$\textregistered$ system during the process of chilling and transport Of the 100pigs tested, the prevalence of level on number of standard plate count (SPC) less than $10^4$ CFU/$\textrm{cm}^2$ and Escherichia coli less than $10^2$ CFU/$\textrm{cm}^2$ in pig were 82% and 80%, respectively. Suface bacterial numbers are decreased in the course of chilling process of the carcass. Alcohol spray process before packing meat also could decrease the surface bacterial count. In conclusion, this study could be overemphasized the importance of relationship between microbiological quality and refrigerating temperature in the process of refrigeration and cutting.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.9
• /
• pp.126-136
• /
• 1995

Copper magnetron anode of a microsave-over consists of an cylindrical outer-tube and various inner-vanes. The magnetron anode is produced by the complex processes; vane blanking, pipe cutting and silver-alloy brazing of vanes. Recently, the backward extrusion process for forming vanes has been developed to avoid the complex procedures. The developed process is analyzed by using upper-bound elemental technique (UBET). In the UBET analysis, the upper-bound load, the configuration and the vane-height of final extruded product are determined by minimizing the roral power consumption with repect to chosen parameters. To verify theoretical analysis, experiments have been carried out with pure plasticine billets at room temperature, using different web-thickness and number of vanes. The theoretical predictions both for forming load and vane-height are in reasonable agreement with the experimental results.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.1
• /
• pp.28-34
• /
• 1999

According to the development of tool material and the improvement of machinability of cutting material like aluminium alloy, the higher spindle speed is needed. However, the higher speed causes the heat generation of bearings, the deformation of spindle unit parts, and the rotational accuracy of spindle to be worse. Therefore, it is essential to analyze and control the heat generation and the thermal behavior of spindle unit in order to have higher speed and better rotational accuracy. This paper shows the analogy between the analyzation of heat generation and thermal behavior of high speed spindle system by finite element method and the test results of actual temperature rise through running test, and shows the necessity of cooling the spindle and inner ring side of bearings for the thermal balance of high speed spindle system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1434-1437
• /
• 2003

Sometimes open holes are required for the function and the weight reduction of structure and machinery. However, the serious stress concentration occurs because of the geometric discontinuity caused by the holes and cutting section. In this study, it is attempted to obtain the stress concentration coefficients of the inner surface of the hole boundary by changing the position and the shape of holes on the homogeneous isotropic plate. And the effects on the plate are investigated. The results show that the stress level becomes low and the distribution area widens the position of stress concentration changes as the ratio a/b increases and change to a circle. And as the ratio a/l decreases, the stress concentration reduces. As the plate with three holes. the stress $\sigma$$\_$x/ and $\tau$$\_$xy/ of hole 1,3 becomes high, especially $\sigma$$\_$x/ dominant and high.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.04b
• /
• pp.204-208
• /
• 1995

Copper magnetron anode of a microwave-oven consists of an cylindrical outer-tube and various inner-vanes. The magnetron anode is produced by the complex process ; vane blanking, pipe cutting and sliver-alloy brazing of vanes. Recently, the backward extrusion process for forming vanes has been developed to avoid the complex procedures. The developed process is analyzed by using upper-bound elemental technique(UBET). In the UBET analysis, the upper-bound load, the configuration and the vane-height of final extruded product are determined by minimizing the total power consumption with respect to chosen parameters. To verify theoretical analysis, experiments have been carried out with pure plasticine billets at room temperature, using different web-thickness and number of vanes. The theoretical predictions both for forming load and vane-height are in reasonable agreement with the experimental results.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.833-836
• /
• 2002

Sometimes open holes are required for the function and the weight reduction of structure and machinery. However, the serious stress concentration occurs because of the geometric discontinuity caused by the holes and cutting section. In this study, it is attempted to obtain the stress concentration coefficients of the inner surface of the hole boundary by changing the position and the shape of holes on the homogeneous isotropic plate. And the effects on the plate are investigated. The results show that the stress level becomes low and the distribution area widens the position of stress concentration changes as the ratio ah increases and change to a circle. And as the ratio a/l decreases, the stress concentration reduces.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.107-107
• /
• 2016

TiCrAlSiN films were developed in order to improve the high-temperature oxidation resistance, corrosion resistance, and mechanical properties of conventional TiN films that are widely used as hard films to protect and increase the lifetime and performance of cutting tools or die molds. In this study, a nano-multilayered TiAlCrSiN film was deposited by cathodic arc plasma deposition. It displayed relatively good oxidation resistance at $700-900^{\circ}C$, owing to the formation protective oxides of $Al_2O_3$, $Cr_2O_3$, and $SiO_2$, and semiprotective $TiO_2$. At $1000^{\circ}C$, the increased temperature led to the formation of the imperfect oxide scale that consisted primarily of the outer ($TiO_2$,$Al_2O_3$)-mixed scale and inner ($TiO_2$, $Al_2O_3$, $Cr_2O_3$)-mixed scale.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.930-937
• /
• 2008

From the result of precise field investigation and stability analysis for the cut slope, following results were acquired. 1. The cause of the collapse of cut slope came from circle sliding collapse by fault zone which remained inner weathering zone. 2. The existing destructed soil and rock can be removed by reinforcement. And to prevent the additional destruction, it is judged that applying the method after relaxing the slope would be reasonable. 3. To make cut slope stable, soft rock layer should be done cutting 1:1.5 and 1:2.0 ~ 1:2.5 for weathered rock and soil layer. 4. Heavy water leakage section should be applied horizontal drain method so that water pressure should not act to the cut slope.