• 한국전기전자재료학회논문지
• /
• 제33권2호
• /
• pp.123-129
• /
• 2020

We analyzed the drift current by charged particles according to the loading methods applied into a closed cell by electronic ink at a reflective-type display panel using an electrophoretic mechanism. For this experiment, various panels were fabricated with injection voltages for electronic ink taking values in the range -4~0 V. The size of each cell was 220 ㎛ × 220 ㎛ and height of the barrier rib was 54.28 ㎛. The electronic ink was fabricated by mixing electrically neutral fluid and single-charge white particles. Drift current was measured by moving charged particles. A biasing voltage of 6 V was applied to the display panel. As a result, the drift current was proportional to the injection voltage for electronic ink, but it decreased in case of an injection voltage above -3 V. Our experimentation ascertained that the concentration of charged particles injected into closed cells is controlled by the injection voltage and the selective injection of charged particles above movable q/m is possible.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1098-1102
• /
• 2008

To increase the ink transfer rate in the micro-gravure-offset printing, the liquid transfer process between two separating plates is investigated. During the liquid transfer process, in which one plate is fixed and the other one moves vertically, a sessile droplet is separated into two droplets. The volume ratio of the two droplets depends on the contact angles of the two plates. In a numerical study of the ink transfer processes, liquid transfer between two parallel separating plates and between a trapezoidal cavity and an upward moving plate are simulated, as models of the printing of ink from the offset pad onto the substrate and the picking up of ink from the gravure plate by the offset pad, respectively. Also, in experimental study, to obtain various surface contact angles, chemical treatment, plasma treatment, and electrowetting- on-dielectric (EWOD) surface are considered. The transfer rate between two plates is calculated by analyzing the droplet images. From the results, the optimal surface contact angles of the units of the micro-gravure-offset printing can be characterized.

• 대한기계학회논문집 C: 기술과 교육
• /
• 제1권2호
• /
• pp.187-192
• /
• 2013

노즐을 이용한 인쇄 기법은 주로 전자 소자의 봉지를 위한 접착제의 인쇄분야에 적용되어 왔다. 노즐 인쇄를 통한 기능성 물질의 필름 형성은 커다란 도전이 될 수 있다. 본 논문에서는 노즐을 이용한 유기 잉크의 인쇄 특성을 실험을 통하여 알아보았다. 본 연구의 노즐 인쇄 실험에서 패턴을 형성하기 위한 잉크는 유기 발광 물질인 TAPC를 사용하였다. 인쇄된 패턴 폭은 잉크 공급 유량의 증가와 기판의 온도의 상승에 따라 증가하였다. 또한 인쇄된 패턴은 건조 후 커피링 형상을 나타내었다.

• 한국재료학회지
• /
• 제27권2호
• /
• pp.82-88
• /
• 2017

Ink-jet printing techniques with ceramic ink, which contains ceramic pigments as colorant, are in increasingly use in the ceramic industry. Generally, ceramic pigments that are produced by conventional method show diameters of several micrometers; these micrometer sized particles in the ink-jet printing process can cause undesirable behavior such as print head nozzle clogging. To prevent this problem, a particle size reduction process is required. In this study, CMYK (cyan, magenta, yellow, black) pigments were synthesized via solid state method. Each pigment particle was milled to submicron size by an attrition mill. The effects of micronizing on the morphology, mechanical property, crystal structure and color property of the CMYK ceramic pigments were investigated by field emission scanning electron microscopy (FE-SEM), particle size analysis (PSA), X-ray diffraction (XRD) and CIE $L^{\ast}a^{\ast}b^{\ast}$.

• 한국정밀공학회지
• /
• 제28권10호
• /
• pp.1123-1130
• /
• 2011

The pattern shape engraved on the gravure printing roll is one of the most important factors influencing ink transfer. This study focuses on the relations between dot geometry engraved on gravure printing roll and the ink transfer during the gravure printing process. The influence of dot width on printed patterns will be demonstrated. Results reveal that as the width of a dot on the printing roll increases, the ink transfer rate also increases. But over a certain size of width, surface uniformity began to recede. Therefore, proper dot geometry on the printing roll should be decided to guarantee good printing quality according to printing conditions and expected performance of the electronic devices.

• 펄프종이기술
• /
• 제46권3호
• /
• pp.1-10
• /
• 2014

Offset paper printing is a promising roll-to-roll technique for color printed materials. Although it is no doubt that understanding ink transfer mechanism in offset printing process is necessary to achieve high printing quality, investing the relationship between inks and substrates at the nip is difficult experimentally due to high printing speed. In this paper, rheological behavior and splitting point of the ink at the nip is studied using package software Ployflow and Flow 3D based on Navier-Stokes equation. Polydimethylsiloxane (PDMS) ink and IGT printability tester were used for an model ink and experiment to compare with that of simulation data, respectively. As a result, higher viscosity at state flow and pressure increased ink transfer due to higher possibility of presence of cavitation at the nip and increase in covering area ratio. These results have shown good agreements with experimental data compared by measuring density of print through.

• 한국재료학회지
• /
• 제16권7호
• /
• pp.422-429
• /
• 2006

Studies were performed on preparation of organic-inorganic hybrid silica dye in a dispersing ink system. The silica was subjected to surface modification using 3-aminopropyltrimethoxysilane (APTMS) in order to promote the chemical reactivity of the raw silica. On the surfaces of the aminosilane-functionalised silica, red vinylsulfone-containing azo dye was adsorbed. The dye was found to have chemically reacted with the aminosilane-grafted silica surface, which was proven by FT-IR spectra. Studies on morphology and microstructure were performed employing scanning electron microscopy. The SEM micrographs and particle size distributions showed that a homogeneous pigment can be obtained employing silica as a core. Particle size distribution was also examined using the technique of dynamic light scattering. The ensuing pigment was subjected to various physicochemical evaluation such as inkjet property, storage stability, color change as inkjet ink using printer, spectrophotometric, microscopic techniques. Studies on hybrid dyes from the silica surface demonstrated that, in general, stable pigments for inkjet dispersion ink were obtained.

• 동아시아식생활학회지
• /
• 제9권4호
• /
• pp.468-474
• /
• 1999

To make rice cake with squid ink, the squid ink dilulted in fifteen times was added to rice flour in the ratio of 0%, 2%. 4%, 6% and 8% respectively. Then, the squid inky rice cake was tested in physical function and chromaticity. Rheometer test was also included in this experiment. In physical function test, it showed that the inky rice cake with 6% and 8% ratio was the best in preference. In the chromaticity test, as the adding ratio of squid ink increases, the brightness decreased. The red and yellow brightness of 8% inky rice cake showed high. The results of rheometer test are as follows. In hardness, the inky rice cake with 2% adding ratio was high and the 6% inky rice cake was low. In cohesiveness, the 0% inky rice cake was high and the 8% inky rice cake was low. In gumminess, the 2% inky rice cake was high and the 6% inky rice cake was low. In brittleness, the 2% inky rice cake was high and the 6% inky rice cake was low. With correlation analysis, 1 could reach the following. The overall quality of inky rice cake was correlated with all test items except chewiness. The moistness was correlated with flavor, grain and chewiness. Also, the 8% inky rice cake was correlated with the inky rice cakes with the other adding ratios in all aspects of test. Futhermore, in the results of rheometer test. the hardness was correlated with the other three kinds of characteristics.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 C
• /
• pp.1623-1624
• /
• 2006

It is a paper for design, manufacture and estimation of industry inkjet head. Simulations for Actuator, Ink flow and Ejection are executed for securing design ability. Relations between droplet and properties of ink are explained closely through simulation for nozzle. Actually, two silicon plates are made by dry and wet etching and directly bonded. PZT materials is attached on the bended ink flow part and cut to $540{\mu}m$ interval by dicing saw. Actuator was seen variation within 10% between simulation and actual head. Through the ejection estimation, it is shown that stabilized driving voltages change according to viscosity and surface tension of metal ink. Using the metal ink of viscosity of 4.8 cps and surface tension of 0.025 N/m, it is possible to eject the stable droplets with 5m/s, 20 pl, 5 kHz.

• 한국인쇄학회지
• /
• 제29권1호
• /
• pp.75-83
• /
• 2011

As screen printing is changed by automation recently, could print more exactly. However, must suffer great many trial and error to have still gotten perfect result. By the way, at this step, fair time and money should be invested. Therefore, if search for optimum condition in early time visualizing screen printing process using simulator program before progress printing, is judged that may be correct and gets printing result efficiently. In this paper, searched optimum printing speed and ink viscosity using FLOW-3D program. Also, the result could confirm truth that is agreeing almost with experiment contents. Through this, is thought that may expect extension of screen printing wide application that vivify advantage of screen print if use simulation program.