• The Korean Journal of Physiology
• /
• v.29 no.1
• /
• pp.81-89
• /
• 1995

The effects of prolactin and vasopressin on the regulation of amniotic fluid (AF) volume and its $Na^{+}$ concentration $([Na^{+}])$ through the membrane surrounding the AF during increase in AF volume due to fetal urination were studied. About 70% of AF volume was replaced with normal isotonic saline solution. Isotonic saline solution (0.5 ml) containing Censored and LiCl was introduced into each amniotic sac. Vasopressin (25 ng/ml) or prolactin (1 mg/ml) of AF was then injected into experimental amniotic sac. The concentrations of Congored, $Li^{+}$, and $Na^{+}$ were measured at 30 and 60 min intervals after injection. Af samples with decreased Censored concentration ([CR]) during the period of 30 - 60 min were analyzed. The percentage change of $[Na^{+}]$ and the rate of $Li^{+}$ movement during this period were calculated, and the effects of vasopressin and prolactin on them were evaluated. Fellowing results were obtained: 1. The rate of reduction of [CR] in the AF was retarded by vasopressin or prolactin injection. 2. The rate of reduction of $[Li^{+}]$ in the AF was also retarded by vasopressin or prolactin injection. 3. The rate of reduction of $[Li^{+}]$ in the AF was less retarded by vasopressin than that of [CR]. 4. $[Na^{+}]$ changed to approach to the normal level, but this was markedly retarded by prolactin injection. 5. Direction of $Li^{+}$ movement was correlated with the change in $[Na^{+}]$ but it always moved out of the amniotic sac even when the $[Na^{+}]$ increased in vasopressin injected AF. From the above results, it is suggested that vasopressin in the AF triggers the fetus to urinate, and then the membranes surrounding the AF regulate osmolarity by efflux of $Na^{+}$. We suggest that prolactin facilitates water outflow across the amniotic membrane during increase in AF volume, in contrast to a constant volume, whereas regulation of $[Na^{+}]$ is partly restricted by prolactin.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.14 no.6
• /
• pp.617-635
• /
• 2012

In this study, correlations between the rock mass permeability before and after grouting & injection volume and the parameters of Q system were investigated on a grouted rock mass tunnel corresponding to rock class 4 and 5 in terms of Q classification system. As a result, it appears that the lower the Q value is, the higher the before-grouting permeability becomes and the smaller the injection volume of grouting becomes. Also RQD and Jn are the most influencing factors to the permeability of rock mass and the injection volume of grouting. In addition, it turned out that it was very difficult to lower the permeability of rock mass smaller than $1.0{\times}10^{-8}$ m/sec with the ordinary portland cement grout.

• Journal of ILASS-Korea
• /
• v.7 no.3
• /
• pp.38-44
• /
• 2002

The purpose of this study is to investigate the effect of the volume fraction of water and injection pressure on the spray characteristics of water/oil emulsified fuel injected from the pressure swirl atomizer. The mixture of light oil and water by using impeller mixer was performed. The spray characteristics such as SMD and velocity were measured using PDPA. The injection pressures were 7.5, 100, 200 and $300kgt/cm^2$ and volume fractions of water in emulsified fuel were 0, 10, 20 and 30%, respectively. The measurement sections were at 30, 60 and 90mm from injection nozzle tip. SMD and velocity of emulsified fuel were larger gradually by increasing the volume fraction of water in emulsified fuel. The spray angle was decreased and axial velocity was increased with increase in water content. It was found that the relative SMD ratio was increased more greatly than the relative axial velocity ratio in super critical pressure. The relative SMD ratio was increased and the relative axial velocity ratio was decreased with increase injection pressure at spray downstream.

• Journal of the Korean Geosynthetics Society
• /
• v.18 no.3
• /
• pp.79-88
• /
• 2019

This study described a results of groundwater injection test in cavity, in order to evaluate characteristics of cavity expansion under pavement. That is, groundwater amount proportional to the cavity volume was injected into the generated cavity step by step, and then the cavity with the changed size was monitored as the injected groundwater was drained. The test result showed that the cavity volume by groundwater injection increased, and then it converged or decreased. This means that some of the relaxation soil around the cavity collapsed, and the fine-grained soils in some soils filled the void in the surrounding soils when the cavity is expanded by groundwater injection. The volume change and expansion characteristics of the cavity according to the groundwater injection step were analyzed. The result showed that the cavity extended laterally. Therefore, it was found that the cavity expansion is caused by the repetition of the relaxation soil collapse due to the groundwater flow and the loss of the collapsed soil below the cavity.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.333-334
• /
• 2002

Injection-compression molding parts are many cases with complicated boundary condition which is difficult to analysis of mold characteristics precisely. In this study, the effects of various process parameters such as multi-point gate location, initial charge volume, injection time and pressure have been investigated using finite element method to fomulate the melt front advancement during the mold filling process. A general governing equation for tracking the filling process during injection-compression molding is applied to volume of fluid method. To verify the results of present analysis, they are compared with those of the other paper. The results show a strong effect of processing conditions as a result of variations in the three-dimensional complex geometry model.

• Journal of ILASS-Korea
• /
• v.17 no.4
• /
• pp.178-184
• /
• 2012

The aim of this study was to compare the spray characteristics of a typical fuel (100% diesel, DME) and diesel-DME blended fuel in a constant volume combustion chamber (CVCC). The typical fuel (100% diesel, DME) and diesel-DME blended fuel spray characteristics were investigated at various ambient pressures (pressurized nitrogen) and fuel injection pressures using a common rail fuel injection system when the fuel mixture ratio was varied. The fuel injection quantity and spray characteristics were measured including spray shape, penetration length, and spray angle. Common types of injectors were used.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.8
• /
• pp.1132-1140
• /
• 1998

The disintegration process of initial spray from high-pressure swirl injector was investigated at different injection pressures. The transient breakup phenomena that were difficult to observe at high injection pressure were easily observed at the low injection pressure of 0.4MPa. The effect of fuel remained inside a nozzle hole volume on the penetration of initial spray was also investigated. The disintegration process of initial spray could be classified four regions: the formation of mushroom shape, the first collision, the second collision, and the development of spray, The liquid film of cup shape was particularly found in the second collision region, and the growth ratio of its length and width at low and high injection pressures were compared.

• Journal of ILASS-Korea
• /
• v.8 no.4
• /
• pp.31-38
• /
• 2003

Constant volume combustion chamber has been designed to investigate diesel spray characteristics with Common-Rail injection system to realize high pressure injection. In this study, two methods of measurements, Schlieren shadowgraphy and Mie scattering imaging method ate applied experimentally to study spray form and liquid phase zone in high pressure, high temperature conditions. Diesel fuel is injected at the point which ignited mixture gas is completely burned. The effect of injection pressure, injector hole diameter, ambient gas temperature and density are investigated experimentally.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.45-53
• /
• 2004

An experimental study was carried out to obtain the fundamental data about the effects of radicals induced injection on premixture combustion. A constant volume combustor divided to the sub-chamber and the main chamber was used. The volume of the sub-chamber is set up to occupy less than 1.5％ of that of whole combustion chamber. Radial twelve narrow passage holes are arranged between the main chamber and the sub-chamber. The products including radicals generated by spark ignition in the sub-chamber will derive the simultaneous multi-point ignition in the main chamber. While the equivalence ratio of pre-mixture in the main chamber and the sub-chamber is uniform. We have examined the effects of the sub-chamber volume, the diameter of passage hole, and the equivalence ratio on the combustion characteristics by means of burning pressure measurement and flame visualization. In the case of radical ignition method(RI), the overall turning time including the ignition delay became very short and the maximum burning pressure was slightly increased in comparison with those of the conventional spark ignition method(SI), that is, single chamber combustion without the sub-chamber. The combustible lean limit by RI method is extended to more ER=0.25 than that by SI method. Therefore the decrease of every emission including NOx and the improvement of fuel consumption is anticipated due to lean burn.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.12
• /
• pp.1021-1030
• /
• 2016

The runner system of the injection mould and the injection volume of the injection molding process greatly affect the quality of the produced part. The goal of this paper is the design of the runner system and the prediction of the injection volume for the injection moulding of a housing part of small-size air cleaner to improve the formability through the three-dimensional injection moulding analysis. The effects of the runner system of the mould on the injection moulding characteristics are investigated. From the results of the investigation, a proper design of the runner system with uniform filling characteristics and the minimized defect formation is obtained. In addition, the influence of the moving distance of the screw on filling characteristics, weldline formation and deformation characteristics is examined. From the results of the examination, an appropriate moving distance of the screw for the housing part of small-size air cleaner is estimated.