• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 D
• /
• pp.1956-1958
• /
• 1999

The analysis of hole injection efficiency at the p+/n-drift layer junction in non-punchthrough IGBT structure is presented. This analysis takes into account carrier concentration variations by conductivity modulation. Good agreement between this analysis and simulation is found over a wide range of carrier lifetime and current density. The proposed analytical model of the hole injection efficiency as a function of collector width, collector concentration has been verified by device simulator, ATLAS.

• 한국수소및신에너지학회논문집
• /
• 제27권1호
• /
• pp.106-113
• /
• 2016

Lean burn engine, classified into port injection and direct injection, is recognized as a promising way to meet better fuel economy. Especially, LPG direct injection engine is becoming increasingly popular due to their potential for improved fuel economy and emissions. Also, LPDi engine has the advantages of higher power output, higher thermal efficiency, higher EGR tolerance due to the operation characteristics of increased volumetric efficiency, compression ratio and ultra-lean combustion scheme. However, LPDi engine has many difficulties to be solved, such as complexity of injection control mode (fuel injection timing, injection rate), fuel injection pressure, spark timing, unburned hydrocarbon and restricted power. This study is investigated to the influence of spark timing, fuel injection position and fuel injection rate on the combustion stability of LPDi engine. Piston shape is constituted the bowl type piston. The characteristics of combustion is analyzed with the variations of spark timing, fuel injection position and fuel injection rate (early injection, late injection) in a LPDi engine.

• 한국수소및신에너지학회논문집
• /
• 제9권1호
• /
• pp.1-7
• /
• 1998

Most of today's energy supply is obtained from fossil fuels. Despite of high energy density, higher store efficiency and long mileage, fossil fuels cause environmental pollution and their reserves are limited. In this study pure hydrogen gas and oxygen gas are burned without the emission of pollution. A gas turbine is used to obtain power. Water is injected into a combustor, which prevents overheating and recovers cooling heat. Excessively supplied water is recirculated. With variation of mass flow rate and equivalence ratio, the affection of water injection rate and the temperature of injected water on efficiency and power are experimented. Injected water gets cooling heat, is expanded from liquid to vapor and raises the thermal efficiency. It is enable to determine the rate of water injection, which makes the maximum power. The increase of temperature of water injection raises the efficiency of the system.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.69-70
• /
• 2006

We studied increasement of efficiency of Organic Light-emitting Diodes depending on thickness variation of LiF, Material of Electron Injection Layer in structure of ITO/Hole Injection Layer (PTFE)/Hole Transportion Later (TPD)/Emitting Layer (Alq3)/Electron Injection Layer (LiF)/Al. TPD and $Alq_3$ is deposited as rate of 1.3~1.5 [${\AA}/s$] in high vacuum ($5{\times}10^{-6}$ [torr]). In result of these studies, we can know maximum efficiency in 0.7 [nm], thickness of LiF. And samples with electron injection material are increased about 5-fold in maximum efficiency in compare with sample without electron injection material.

• 한국추진공학회지
• /
• 제13권4호
• /
• pp.45-54
• /
• 2009

열효율과 비동력을 대폭 향상시킬 수 있는 잠재성을 가진 증기분사 재생 가스터빈 시스템에 대해 엑서지 해석을 수행하였다. 열역학 제2법칙을 근거로 한 해석 모델을 이용하여 압력비, 증기분사율, 주위 온도, 터빈입구온도 등 주요 설계변수들의 변화에 따라 엑서지 효율, 열교환기의 엑서지 회수율, 엑서지 파괴율 및 손실률 등 시스템의 성능과 최대 엑서지 효율에 미치는 영향을 조사하였다. 계산 결과 재생 증기분사 가스터빈 시스템은 시스템의 엑서지 효율을 대폭 증대시키고 비가역성을 감소시킨다는 사실을 확인하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.379-379
• /
• 2010

Recent technical advances in OLEDs (organic light emitting devices) requires more and more the improvement in low operation voltage, long lifetime, and high luminance efficiency. Inverted top emission OLEDs (ITOLED) appeared to overcome these problems. This evolved to operate better luminance efficiency from conventional OLEDs. First, it has large open area so to be brighter than conventional OLEDs. Also easy integration is possible with Si-based driving circuits for active matrix OLED. But, a proper buffer layer for carrier injection is needed in order to get a good performance. The buffer layer protects underlying organic materials against destructive particles during the electrode deposition and improves their charge transport efficiency by reducing the charge injection barrier. Hexaazatriphenylene-hexacarbonitrile (HAT-CN), a discoid organic molecule, has been used successfully in tandem OLEDs due to its high workfunction more than 6.1 eV. And it has the lowest unoccupied molecular orbital (LUMO) level near to Fermi level. So it plays like a strong electron acceptor. In this experiment, we measured energy level alignment and hole current density on inverted OLED structures for hole injection. The normal film structure of Al/NPB/ITO showed bad characteristics while the HAT-CN insertion between Al and NPB greatly improved hole current density. The behavior can be explained by charge generation at the HAT-CN/NPB interface and gap state formation at Al/HAT-CN interface, respectively. This result indicates that a proper organic buffer layer can be successfully utilized to enhance hole injection efficiency even with low work function Al anode.

• Transactions on Electrical and Electronic Materials
• /
• 제6권5호
• /
• pp.233-237
• /
• 2005

In the device structure of ITO/hole injection layer/N, N'-biphenyl-N, N'-bis-(1-naphenyl)-[1,1'-biphenyl]4,4'-diamine(NPB)/tris(8-hydroxyquinoline) aluminum$(Alq_3)/Al$, we investigated an effect of hole-injection materials (PTFE, PVK) on the electrical characteristics and efficiency of organic light-emitting diodes. A thermal evaporation was performed to make a thickness of NPB layer with a evaporation rate of $0.5\~1.0\;\AA/s$ in a base pressure of $5\times10^{-6}$ Torr. We measured current-voltage characteristics and efficiency with a thickness variation of hole-injection layer. The PTFE and PVK hole-injection layer improve a performance of the device in several aspects, such as good mechanical junction, reducing the operating voltage and energy band adjustment. Compared with the devices without a hole-injection layer, we have obtained that an optimal thickness of NPB was 20 nm in the device structure of $ITO/NPB/Alq_3/Al$. And using the PTFE or PVK hole-injection layer, the external quantum efficiencies of the devices were improved by $24.5\%\;and\;51.3\%$, respectively.

• 대한환경공학회지
• /
• 제32권1호
• /
• pp.17-22
• /
• 2010

본 연구의 목적은 대형 석탄 화력 발전소에 DSI (Dry Sorbent Injection)공정을 실제 적용 할 경우에 실현 가능성에 대한 연구로서 N 발전(주)의 S 화력발전본부에서 운용중인 500MW급 석탄화력 발전시설의 보일러 후단에서 전기 집진기 전 단까지를 모델로 삼아 Lab-scale 실험장치를 제작하여 탈황효율을 높이기 위한 실험을 수행하였다. 이를 위하여 Lobedplate와 Step-plate라는 혼합촉진장치를 고안하고 각각 형상을 달리하여 궁극적으로 탈황효율을 높이기 위한 혼합촉진장치의 최적 형상도출을 위한 실험을 수행하였으며 부수적으로 탈황제의 분사구의 개수에 따른 탈황효율 또한 분석하였다. 그 결과 혼합촉진장치가 설치된 경우가 더 높은 탈황 효율을 나타내었고 형상에서는 계단형상일 경우 가장 높은 탈황효율을 보였다. 또한, 탈황제의 분사구의 개수에 따른 탈황효율은 혼합 촉진 장치가 설치되지 않은 경우, 분사구의 개수가 증가할수록 높은 탈황 효율을 보였으나 혼합촉진장치가 설치된 경우는 분사구의 개수가 4개일 경우가 이론적 결과와 같이 가장 높은 탈황효율을 나타내었다.

• Geomechanics and Engineering
• /
• 제25권1호
• /
• pp.31-40
• /
• 2021

Injection grouting is one of the most common ground improvement practice to increase the strength and reduce the hydraulic conductivity of soils. Owing to the environmental concerns of conventional grout materials, such as cement-based or silicate-based materials, bio-inspired biogeotechnical approaches are considered to be new sustainable and environmentally friendly ground improvement methods. Biopolymers, which are excretory products from living organisms, have been shown to significantly reduce the hydraulic conductivity via pore-clogging and increase the strength of soils. To study the practical application of biopolymers for seepage and ground water control, in this study, we explored the injection capabilities of biopolymer-based grout materials in both linear aperture and particulate media (i.e., sand and glassbeads) considering different injection pressures, biopolymer concentrations, and flow channel geometries. The hydraulic conductivity control of a biopolymer-based grout material was evaluated after injection into sandy soil under confined boundary conditions. The results showed that the performance of xanthan gum injection was mainly affected by the injection pressure and pore geometry (e.g., porosity) inside the soil. Additionally, with an increase in the xanthan gum concentration, the injection efficiency diminished while the hydraulic conductivity reduction efficiency enhanced significantly. The results of this study provide the potential capabilities of injection grouting to be performed with biopolymer-based materials for field application.

• 한국수소및신에너지학회논문집
• /
• 제27권2호
• /
• pp.211-219
• /
• 2016

To develop an ash separator for the solid fuel chemical looping combustion system, effects of operating variables such as solid injection nozzle velocity, diameter of solid injection nozzle, gap between solid injection line and vent line, vent line inside diameter, and solid intake height on solid separation rate and solid separation efficiency were measured and discussed using heavy and coarse particle and light and fine particles mixture as bed material in an acrylic fluidized bed apparatus. The solid separation rate increased as the solid injection nozzle velocity and the diameter of solid injection nozzle increased. However, the solid separation rate decreased as the gap between solid injection line and vent line, the vent line inside diameter, and the solid intake height increased. The solid separation efficiency was in inverse proportion to the solid separation rate. In this study, we could get high solid separation rate up to 2.39 kg/hr with 91.6% of solid separation efficiency.