• The Korean Journal of Emergency Medical Services
• /
• v.20 no.1
• /
• pp.57-70
• /
• 2016

Purpose: This study aims to analyze the current state of emergency care for patients with anaphylaxis and to identify problems and areas for improvement in prehospital care. Methods: This study was conducted using 119 emergency running sheets and medical records of 109 patients diagnosed with anaphylaxis. Questionnaires were also given to emergency medical technicians (EMTs) and emergency physicians. The data were analyzed using SPSS 21.0. Results: Prehospital emergency care included oxygen administration in 64.2%, an intravenous line in 15.6%, and medication injection in 11.0%. The most commonly administered medications were antihistamines in 66.7% and epinephrine in 8.3%. Of EMTs surveyed, 47.0% suggested an epinephrine injection and using direct medical control, while 53.8% of the emergency physicians suggested an epinephrine injection and using indirect medical control. Most emergency physicians 88.8% responded that epinephrine could be administered by EMTs. Conclusion: The data support epinephrine injection of patients with anaphylaxis by EMTs, but a larger sample size of EMTs is required. Education about the treatment of anaphylaxis should be improved for EMTs. The scope of paramedic responsibilities should also be redefined.

• Korea-Australia Rheology Journal
• /
• v.16 no.4
• /
• pp.163-168
• /
• 2004

In this study, an ultrasonic technique was employed to obtain pressure-volume-temperature (PVT) rela­tionship of polymer melt by measuring ultrasonic velocities under various temperatures and pressures. The proposed technique was applied to on-line monitoring of injection molding process as an attempt to predict quality of molded parts. From the comparison based on Tait equation, it was confirmed that the PVT behav­ior of a polymer is well described by the variation of ultrasonic velocities measured within the polymer medium. In addition, the changes in part weight and moduli were successfully predicted by combining the data collected from ultrasonic technique and artificial neural network algorithm. The results found from this study suggest that the proposed technique can be effectively utilized to monitor the evolution of solid­ification within the mold by measuring ultrasonic responses of various polymers during injection molding process. Such data are expected to provide a critical basis for the accurate prediction of final performance of molded parts.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.44 no.4
• /
• pp.62-74
• /
• 2002

The purpose of this study is to find the variation of sedimentation patterns before Saemangeum reclamation. Residual flow before Saemangeum reclamation was calculated diagnostically from the observed water temperature and salinity data in May 1992 by the Marine Development Institute of Kunsan National University and wind data which were obtained from spring 1969 through winter 1977 by the Gunsan Meteorological Observatory. Three dimensional movements of injected particles due to currents, turbulence and sinking velocity are tracked by the Euler-Lagrange method. Calculated sedimentation patterns of riverine materials are highly similar to the observed ones. When suspended sediments with the size of soil grain of 60 ${\mu}m$ are injected from the Mangyeong River, their dispersion range of sediment is about 25km for 24 hours after the injection, while about 35km for 72 hours after the injection. When suspended sediments with the size of soil grain of 200 ${\mu}m$ are injected, their dispersion range of sediment is about 18km for 24 hours after the injection, while about 21km for 72 hours after the injection.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.29 no.2
• /
• pp.431-438
• /
• 2019

Fileless malware uses memory injection attacks to hide traces of payloads to perform malicious works. During the memory injection attack, an attack named "process hollowing" is a method of creating paused benign process like system processes. And then injecting a malicious payload into the benign process allows malicious behavior by pretending to be a normal process. In this paper, we propose a method to detect the memory injection regardless of whether or not the malicious action is actually performed when a process hollowing attack occurs. The replication process having same execution condition as the process of suspending the memory injection is executed, the data set belonging to each process virtual memory area is compared using the fuzzy hash, and the similarity is calculated.

• Korea-Australia Rheology Journal
• /
• v.20 no.2
• /
• pp.79-88
• /
• 2008

In this study, we focus on the improvement of the filling efficiency in injection molding by application of ultrasonic vibration. While studies about the filling efficiency of typical filling processes in the injection molding have been widely performed, there have been only few studies about the filling efficiency of an ultrasonic process. The effect of the ultrasonic vibration is an important process condition, which influences the flow characteristics of polymer melt. This new condition even affects well-known injection conditions such as cavity pressure, injection temperature and mold temperature. For this study, we carried out a numerical analysis by appropriate modeling and analysis of the ultrasonic process in the filling process. To verify this numerical analysis, we compared the numerical results with the experimental data. Also, we analyzed the filling process in a thin cavity using this numerical analysis. To understand the flow characteristics of polymer melt in the ultrasonic process, we substituted real and complex vibration conditions with simplified and classified conditions according to the position of vibrating cavity surfaces and the phase difference between two opposing cavity surfaces. We also introduced MFR (melt flow ratio) as a new index to estimate the filling efficiency in the ultrasonic process.

• Journal of Mechanical Science and Technology
• /
• v.19 no.11
• /
• pp.2040-2052
• /
• 2005

The present paper centers on the establishment of a quantified relationship between the macroscopic visual parameters of a Diesel spray and its most influential factors. The factors considered are the ambient gas density, as an external condition relative to the injection system, and nozzle hole diameter and injection pressure as internal ones. The main purpose of this work is to validate and extend the different correlations available in the literature to the present state of the Diesel engine, i.e. high injection pressure, small nozzle holes, severe cavitating conditions, etc. Five mono-orifice, axi-symmetrical nozzles with different diameters have been studied in two different test rigs from which one can reproduce solely the real engine in-cylinder air density, and the other, both the density and the pressure. A parametric study was carried out and it enabled the spray tip penetration to be expressed as a function of nozzle hole diameter, injection pressure and environment gas density. The temporal synchronization of the penetration and injection rate data revealed a possible explanation for the discontinuity observed as well by other authors in the spray's penetration law. The experimental results obtained from both test rigs have shown good agreement with the theoretical analysis. There have been observed small but consistent differences between the two test rigs regarding the spray penetration and cone angle, and thus an analysis of the possible causes for these differences has also been included.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.5 s.176
• /
• pp.1323-1330
• /
• 2000

Recently, injection molding process became more popular than ever to produce large quantities of high precision products or optical products. Especially, optical disk that was made by injection mol ding process has been used for many years as a music play media or computer sub-device. The density of data in disk media has been increased continuously. But those optical disks can cause sensorial problems because of high birefringence or deformation from the residual stresses in the media. Therefore, it is necessary to study the effects of various process conditions on the final bireffingence structure in injection-molded disks for producing precision injection-molded products. In the present paper we have focussed on the effect of holding and compression pressures on the optical anisotropy remaining in the MOD by examining the gapwise distribution of birefringence and extinction angle. The effect of holding pressure was found to form the inner two bireffingence peaks. But the effect of compression pressure on the bireffingence distribution was found to make the uniform distribution near the center in the gapwise direction. Finally, the value of the birefringence near the wall decreased as the mold temperature increased.

• Design & Manufacturing
• /
• v.2 no.4
• /
• pp.54-61
• /
• 2008

Warpage, which is one of the molding trouble, acts as possible factor which results in defect in assembly. In this study, a mold was designed to produce specimens with rib parallel to flow direction, specimens with rib perpendicular to flow direction and specimens without rib. This work researched change of warpage according to injection molding condition such as injection pressure, packing pressure, packing time, resin temperature, mold temperature in non-crystalline resins(PC, ABS), crystalline resins(PP, PA66), and 30% glass fiber reinforced-resins(PC, ABS, PP, PA66).Specimens with rib and Crystalline resins show more warpage than specimens without rib and non-crystalline resins, respectively. Glass fiber reinforced-resins and specimens with rib parallel to flow direction show smaller warpage than conventional resins and specimens with rib perpendicular to flow, respectively. Specimens with rib and specimens without rib show reduced warpage as packing time increases. In addition, warpage increase as resin temperature increases. It is found that CAE shows similar tendency with experiment as packing time, resin temperature. when the rib is caused, warpage will reduce and prevent the transformation. product of a irregular form occurs warpage. In the study It'll be basic data that product occurs warpage, preferablity.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.4
• /
• pp.377-383
• /
• 2003

As the high-speed data communications such as xDSL using the existing copper cable come into wide use, the electromagnetic coupling characteristics of telecommunication cables become more significant. In order to describe the screening performance of telecommunication cable, the transfer impedance of cable shield is required. This paper describes the transfer impedance for two types of telecommunication cables using the line injection method of IEC 96-1. Results are analyzed to show how the materials of cable shields, the positioning of the injection line and of the inner conductor of the CUT(Cable Under Test) affect the value of transfer impedance. We then propose the transfer impedance model of telecommunication cable based on the measurements.

• Polymer(Korea)
• /
• v.28 no.3
• /
• pp.263-272
• /
• 2004

Using computer simulation, the processibility and properties of the inst겨ment panel of automobile produced by gas injection molding were predicted and evaluated. The P-V-T data of ABS, resin were used in the gas injection molding process in order to estimate the mold filling phenomena. The optimum process conditions were found by adjusting the process parameters including pressure, filling time, the positions of gas channel and runner. The process was simplified and the final instrument panel produced by the gas injection molding was found to have improved dimension stability compared to the one produced by conventional injection molding.