• Steel and Composite Structures
• /
• 제30권5호
• /
• pp.483-492
• /
• 2019

In the current study, the influence of the initial lateral (sweep) shape and the cross-sectional twist imperfection on the lateral torsional buckling (LTB) response of doubly-symmetric steel I-beams was investigated. The material imperfection (residual stress) was not considered. For this objective, standard European IPN 300 beam with different unbraced span was numerically analyzed for three imperfection cases: (i) no sweep and no twist (perfect); (ii) three different shapes of global sweep (half-sine, full-sine and full-parabola between the end supports); and (iii) the combination of three different sweeps with initial sinusoidal twist along the beam. The first comparison was done between the results of numerical analyses (FEM) and both a theoretical solution and the code lateral torsional buckling formulations (EC3 and AISC-LRFD). These results with no imperfection effects were then separately compared with three different shapes of global sweep and the presence of initial twist in these sweep shapes. Besides, the effects of the shapes of initial global sweep and the inclusion of sinusoidal twist on the critical buckling load of the beams were investigated to unveil which parameter was considerably effective on LTB response. The most compatible outcomes for the perfect beams was obtained from the AISC-LRFD formulation; however, the EC-3 formulation estimated the $P_{cr}$ load conservatively. The high difference from the EC-3 formulation was predicted to directly originate from the initial imperfection reduction factor and high safety factor in its formulation. Due to no consideration of geometric imperfection in the AISC-LFRD code solution and the theoretical formulation, the need to develop a practical imperfection reduction factor for AISC-LRFD and theoretical formulation was underlined. Initial imperfections were obtained to be more influential on the buckling load, as the unbraced length of a beam approached to the elastic limit unbraced length ($L_r$). Mode-compatible initial imperfection shapes should be taken into account in the design and analysis stages of the I-beam to properly estimate the geometric imperfection influence on the $P_{cr}$ load. Sweep and sweep-twist imperfections led to 10% and 15% decrease in the $P_{cr}$ load, respectively, thus; well-estimated sweep and twist imperfections should considered in the LTB of doubly-symmetric steel I-beams.

• 한국임상수의학회지
• /
• 제39권4호
• /
• pp.149-155
• /
• 2022

The aim of this study was to compare the mechanical properties of 0.6 and 0.8 mm cerclage wires with the 1.0 mm cerclage wire in the twist, single-loop, double-loop, double-wrap, and loop/twist knot methods. Six stainless steel cerclage wires of various diameters in different knot methods were tied round a customized jig mounted on a load testing machine. The initial tension, initial stiffness, and yield load were evaluated. The failure mode of each cerclage was observed. For each wire size, the double-loop, double-wrap, and loop/twist knots showed significantly greater initial stiffness, and yield load than those seen with twist and single-loop knots. The single-loop knot showed the least initial stiffness regardless of the diameter. As the cerclage wire diameter increased, the cerclage tended to show significantly greater initial stiffness, and yield load. Failure modes varied depending on the knot configurations. Single-loop knots of smaller-diameter wires less than 1 mm had similar or lower initial tension, initial stiffness, and yield load than a twist knot. Owing to the variance in mechanical properties, the clinical application of the knot type should depend on the diameter of the cerclage wire.

• 소성∙가공
• /
• 제12권8호
• /
• pp.718-723
• /
• 2003

Tn order to develop springback control technology for high-strength steel sheets, several studies have been conducted: dome stretching test, stepped s-rail forming and springback measurement, and optimally shaped initial blank design. First, to find out the formability of TRIP60, dome stretching test was performed. Next, the stepped s-rail die, which was designed to form a channel type panel with large twist and wall curl, was manufactured and used to evaluate the effect of controlling forming variables, such as blank holding force and flange amount on the springback. Furthermore, new measurement method of the springback was introduced to define wall curl and twist in geometrically complex panels. Finally, the optimally shaped initial blank was employed to verify one of the best ways to control the springback in channel type. high-strength sheet panels.

• 한국전기전자재료학회논문지
• /
• 제19권2호
• /
• pp.185-188
• /
• 2006

We studied on the reverse twist near the pixel edge depending on the rubbing direction for the fringe field switching (FFS) mode. Liquid crystal (LC) dynamic and the transmittance near the pixel edge, where the various field directions are generated, depend on the initial rubbing direction because the position of reverse twist is decided by the angle between the electric direction and the LC director at a bias voltage. For example, when the rubbing angle is $7^{\circ}$, the reverse twist appears on the bottom position of the right sharp comer of the pixel edge so that the reverse region exists far away from main active region. But, when the rubbing angle is $-7^{\circ}$, the reverse twist appears on the top position of the right sharp comer of the pixel edge, resulting that the region becomes more close to the main active area and the unstable disclination lines (DLs) easily intrude into the active region. Therefore, it is necessary to keep the reverse twist region far from the active region and it is possible by controlling the rubbing direction in the design of a pixel electrode.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.209-212
• /
• 2004

A navel fast-switching LCD with dual-domain bend (DDB) mode is described DDB alignment is achieved using antiparallel-rubbed cell filled with chiral-doped LC. Initial alignment is mono-domain 180-degree twist. Tilt direction is controlled by oblique electric field to be counter direction in each domain Twist-to-DDB deformation occurs continuously so that DDB mode does not require high-voltage initialization which is inevitable in Optically Compensated Bend (OCB) mode. DDB gives wide and symmetric viewing angle in contrast to mono-domain bend formed from 180-degree twist showing strong asymmetry.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 춘계학술발표대회 논문집
• /
• pp.127-130
• /
• 2002

Vibration analysis of rotating blade is the main purpose of the present study. In this study, general formulation is performed for rotating shell structures including the centrifugal force, Coriolis acceleration and initial twist. Furthermore, simplified equations are derived for the case of an open cylindrical shell. Based on the concept of degenerated shell element with the Reisser-Mindlin's assumptions, the finite element method is adopted for solving the problems. In addition, it is investigated the effect of the stacking sequence of the composites on the vibration characteristics of the blade. The results are summarized for the various parameters such as the speed of rotation and pre-twist of the blade. Also, present results are compared with the previous works and experimental data.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 제4회 박판성형 심포지엄
• /
• pp.35-40
• /
• 2003

In order to develope springback control technology for high-strength steel sheets, some studies have been conducted: dome stretching test, stepped s-rail forming and springback measurement, and optimally shaped initial blank design. First, to find out the formability of TRIP60, dome stretching test was performed. Next the stepped s-rail die, which was designed to form a channel type panel with large twist and wall curl, was manufactured and used to know the effect of controlling forming variables, such as blank holding force and flange amount on the springback. Furthermore, new measurement method of the springback was introduced to define wall curl and twist in geometrically complex panels. Finally, the optimally shaped initial blank was employed to verify one of the best ways to control the springback in channel type, high strength sheet panels.

• 한국의류산업학회지
• /
• 제12권4호
• /
• pp.500-507
• /
• 2010

In this study, physical properties were studied by using latent stretching yarn in order to develop the texturing yarn technique for super bulky yarn, which is better in bulkiness and handle than natural wool and also adds property of synthetic fiber to natural wool. In order to obtain textured conditions by analysing basic properties for manufacturing DTY yarn with super bulky property, DTY 50d/12 after spinning latent yarn spined POY 80d/12 was obtained under the two conditions of (i) false twist(T/M) level 3 in DTY texturing and (ii) draw ratio level 4 in draw texturing. For DTY texturing yarn, Elongation rate increased as the heat treatment time and temperatures increased. In addition, shrinkage became higher as false twist was higher, so that elongation rate became lower. When annealing became longer in time and higher in temperature, initial modulus increased. In addition, as the count of false twist increased, the initial modulus showed higher values. For draw texturing yarn, under the conditions of heat temperature 180 and heating time 30 minutes, shrinkage rate in draw ratio 1.55 and 1.6 draw ratio was 7%, and that in 1.65 and 1.7 draw ratio was 8.5%. High draw ratio samples' tenacity was much influenced by heating time and temperature, but low draw ratio samples' tenacity was influenced not by treated time, but by treated temperature.

• 한국염색가공학회지
• /
• 제12권2호
• /
• pp.89-95
• /
• 2000

Effect of twist-setting time, temperature and cylinder layer for the physical properties of the twist yarn were investigated by separated 9 layer from yarn cylinder. Obtained results were as follow. Shrinkage of the yarn in middle layer shows high value with heat-permeation and in inner's shows low value because of cylinder hardness. And then yarn thermal shrinkage in outer layers shows more or less high value because twist yarn in the outer layer sets more faster. Concerning to the difference on the yam physical properties among cylinder layers, the changes on physical properties shows significant differences from the 7th layer to the last one. Linear density, T.P.M and initial modulus decreases but snarl index increases.

• 한국의류산업학회지
• /
• 제5권4호
• /
• pp.408-412
• /
• 2003

The micro structure of POY was modified and a wool-like touch yarn of composite fibers with different shrinkage was made. With this yarn 12 different fabrics with wool like touch were prepared. The characteristic physical property changes of the fabrics examined are as follows: 1. In all cases, the initial high shrinkage stages were observed in hot water treatment and the 3D images of complex multilayer of typical doubling fibers with different shrinkage were also observed in hot air treatment of 170C. 2. The tensile strength changes of satin and plain fabrics with the change of twist count showed similar behavior. However, WT's were slightly higher and RT's was lower in twill and satin fabrics than those in plain fabric. 3. Since a slight decrease of B's of twill fabric found with increasing twist count under given experimental condition, it could be influenced on the anti-drape stiffness was decreased and flexibility was increased. 4. A significant decrease of G values was observed in the twist count 800-1000 T.P.M However, in the twist count higher than 1000 T.P.M G values observed were kept nearly constant. 5. MIU of plain and twill fabrics showed a drastic decrease at the twist count higher than 1000 T.P.M.