• 한국항공우주학회지
• /
• 제44권7호
• /
• pp.568-575
• /
• 2016

항공기로부터 방사되는 IR 신호(Infrared : IR)는 전투 생존성 관점에서 예측과 분석이 필요하다. 본 연구에서는 배기 플룸에서 발생하는 IR 신호에 대해 IR 탐지기 관점에서 신호 예측을 수행하였다. 복사 데이터베이스와 이를 활용하는 Line-By-Line 기법을 적용하여 복사 물성치를 해석하고 이를 바탕으로 1차원 Line Of Sight(LOS)에 대해 복사 강도를 해석하였다. 상용 프로그램을 이용하여 노즐의 배기 플룸 열유동장을 해석하였고, 이 플룸 열유동장에 IR 탐지기 관점에서 서로 다른 탐지 각도에 대한 LOS를 설정하여 이에 대한 IR 신호 해석을 수행하였다. 해석을 통해 플룸 내부의 국부적으로 높은 온도 영역을 지나는 LOS에서 강한 IR 신호가 확인되었다. 또한 노즐 벽면을 포함한 LOS에서 가장 강한 IR 신호가 확인되었으며, 이를 통해 고체 벽면에 의한 복사 방사가 IR 신호에 큰 영향을 미치는 것을 확인하였다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.2221-2225
• /
• 2003

As a result of using a heat generator to experiment the physiological influence of the human body due to the warming effect of far-infrared radiation (FIR), the blood pressure of the subjects lowered and stabilized due the expansion of capillary vessels and salt discharge during perspiration as the temperature of the generator elevated($30{\sim}65^{\circ}C$). In case of heart rate, it decreased and stabilized when the temperature of the ‘far-infrared radiation heat generator’ was at a low temperature below $40^{\circ}C$. At a high temperature above $44^{\circ}C$, there was a slow elevation in the heart rate. However, the elevation of the heart rate is not a sudden elevation, therefore, does not give much stress to the heart.

• Journal of the Korean Wood Science and Technology
• /
• 제37권5호
• /
• pp.440-450
• /
• 2009

In case of wood flooring, the high emissivity would be one of the most important properties especially as the cover material of underfloor heating system. The FIR (Far Infrared) materials such as wood emit FIR energy by heating, which has been used as the medical therapy such as dry sauna. This research investigated the emissivity and the emission power of wood composites by comparing the amount of the three heat transfer modes transferred by infrared radiation which came from the increased temperature of the bottom board of the plywood box by the heater. The results showed the value of radiation mode was the highest mode for the plywood box, and the convection mode was the main mode for the aluminum box. The rate of convection was 81.8% in the aluminum box and 48.2% in the plywood box, respectively. In case of the rate of radiation, the aluminum box showed only 15.4% and the plywood box showed 51%. The emissivity and the emission power of birch plywood showed the same values as those of wood. The amount of energy required for the temperature rising of water within vial in the aluminum box and in the plywood box were 3.32 kJ and 6.70 kJ respectively, which showed that the vial temperature of the plywood box was two times higher than that of the aluminum box.

• 한국산업융합학회 논문집
• /
• 제6권1호
• /
• pp.65-71
• /
• 2003

Infrared heating has been traditionally used in industrial applications for processes such as dehydration of food industrial. This heating method involves the application of radiation in the wavelength range of 5~50 micrometers. In this work, simultaneous heat balance equations were developed to simulate the infrared radiation heating of red peppers. The equations assume that moisture diffuses to the outer boundaries of the material in liquid form and evaporation occurs at the surface of the red peppers. Energy for moisture evaporation is supplied by the infrared radiant energy. The equations were validated with experimental data on surface temperature and average moisture content of red peppers. Average deviations of predicted surface red peppers temperature and average red peppers moisture from experimental data were 323~353K and 50~80%, respectively. The spectral extinction coefficients in the wavelength range $1.5<{\lambda}<27$ micrometer at 293K for Red Peppers were determined from results of reflection measurements and the four flux radiative heat transfer calculation. The radiation extinction coefficients were obtained from effective drying factor the temperature 373K.

• 천문학회보
• /
• 제36권2호
• /
• pp.72.2-72.2
• /
• 2011

We have performed the first self-consistent, large-scale simulation of cosmic reionization by stellar sources, including the Population III stars that emerged and were hosted by minihalos at very high redshifts (z~40). Based on this result, we calculate the redshifted radiation background from these stars and the relic H II regions which can be observed at near-infrared and infrared regime. Formation of the first stars inside minihalos are quenched by radiative feedback at z~15, while the relic H II regions have much longer lifetime due to the slow recombination rate. Therefore, the radiation output from the relic H II regions, dominated by Lyman alpha photons, will be observed both in the near-infrared and infrared regime. The estimated background from the first stars inside minihalos are still sub-dominant compared to that from stars inside larger halos, however, and thus complementary observations are necessary, such as redshifted 21-cm line observation.

• 한국구조물진단유지관리공학회 논문집
• /
• 제3권2호
• /
• pp.185-190
• /
• 1999

It is difficult to estimate for deterioration of exterior wall by infrared thermography, because of amount of infrared-ray radiation effected by environmental factors such as temperature properties of materials, the outside air and the amount of solar radiation. Therefore we measured the distribution of temperature by times in the same reinforced-concrete structure in order to reduce problems, occasioned by environmental factors, then we analyzed physical influence factors of the infrared thermography. It is the aim of this study to suggest basic data with regard to method of estimation-system for deterioration of exterior wall in reinforced-concrete structures.

• 한국가구학회지
• /
• 제11권1호
• /
• pp.61-68
• /
• 2000

This study was carried out to investigate the effect of grain and veneer thickness on drying rate, required energy consumption, and drying defects such as checking, end waving, and burning during a far-infrared radiation drying process of decorative veneers of hard maple and beech. Most of the veneer could be dried from green to in-use moisture content within 30 to 360 seconds. The drying rates were significantly affected by veneer thickness, but there was little difference between edge-and flat-sliced veneers. The formation of checking during drying test was none or very slight. The percentages of the veneers defected by checks were higher in the flat-sliced veneers than in the edge-sliced veneers. The maximum end wavinesses in the flat-sliced veneers were almost 1.6 to 3 times larger than that in the edge-sliced veneers. All veneers were fee from burned marks during drying test.

• 대한조선학회논문집
• /
• 제44권4호
• /
• pp.459-465
• /
• 2007

This paper deals with the development of measuring methodology and the requirement for its evaluation of the infrared radiation from a naval ship to optical sensors, considering the Meteorological conditions. Factors required for measuring the apparent temperature and infrared radiation are identified and two methods are suggested based on the measuring instruments carried by ship or aircraft. and target operation in the Meteorological conditions is considered. This study describes some factors affecting the IR signature. required instruments to obtain the IR signal considering the naval ship.

• Journal of the Korean Wood Science and Technology
• /
• 제25권4호
• /
• pp.22-28
• /
• 1997

This research was carried out to obtain the fundamental data for the development of the technology and practical use of far-infrared radiation(IR) drying of quarter-sliced decorative veneers of walnut and red oak. The average drying rates of IR drying were about one and half to four times those of kiln drying and this tendency was prominent in thin veneer. The end wavinesses of the IR-dried veneers were smaller than those of kiln-dried veneers. These were largely recovered by the cold treatments after drying. The consumed electric power for IR drying was about one-fifth to two-fifthes compared to that for kiln drying.

• 설비공학논문집
• /
• 제18권8호
• /
• pp.672-677
• /
• 2006

The steady cooling characteristics of a cryochamber for infrared (IR) detector have been investigated analytically, considering radiation shields. The thermal modeling considers the conduction heat transfer through cold finger, the gaseous conduction due to out-gassing, and the radiation heat transfer. The cooling load of the cryochamber is obtained by using a fin equation. The results obtained indicate that the gaseous conduction plays an important role in determining the steady cooling load. The steady cooling load is increased as the gas pressure is increased. It is also found that the cooling load is substantially decreased with a radiation shield. The most thermal load of a cryochamber occurs through the cold finger.