• Bulletin of the Society of Naval Architects of Korea
• /
• v.27 no.4
• /
• pp.51-57
• /
• 1990

There exist residual stresses and deformations in welded structures because of nonuniform temperature distribution. The thermal elasto-plastic analysis is necessary to describe the behavor of the structure during welding. In this paper, we calculated the residual stresses and deformations of the welded beam using the I-dimensional layered beam theory. In the previous 1-dimensional analyses, there were restrictions that the equilibrium conditions which were effective only on beams with infinite length were used, and the boundary conditions could not be considered adequately. But, the layered beam theory based on the incremental finite element method, can overcome these restrictions. On the other hand, in the 2-dimensional analysis, the computing time is large because of many degrees of freedom, and there was inaccuracy in the calculation of welding deformations. However, the layered beam theory can take into account the variation of properties along the depth, and can reduce the degrees of freedom considerably in comparision with the 2-dimensional analysis, and shows good agreement with the experiments.

• The Journal of the Acoustical Society of Korea
• /
• v.34 no.3
• /
• pp.219-226
• /
• 2015

In this paper, derivation of the STL (Sound Transmission Loss) of a square plate installed in an impedance tube is discussed using an analytic method. Coupled motion of the plate vibration and acoustic field is considered. Vibration of the plate and pressure field inside the tube are expressed in terms of the infinite series of modal functions. Under the plane wave assumption, it is shown that consideration of the first few modes yields sufficiently accurate results. When the boundary of the plate is clamped, vibration mode is assumed as a multiplication of the beam modes corresponding to the crosswise directions. The natural frequencies of the clamped plate are calculated using the Rayleigh-Ritz method. It is found that the STL shows a dip at the lowest natural frequency of the plate, and increases as the frequency decreases below the natural frequency. Comparison of the result in this paper with the STL obtained by measurements and FE computations in the reference shows an excellent agreement.

• The KSFM Journal of Fluid Machinery
• /
• v.17 no.1
• /
• pp.35-40
• /
• 2014

A multi-objective optimization of a regenerative fan for enhancing the aerodynamic and aeroacoustic performance was carried out using an integrated fan design system, namely, Total FAN-Regen$^{(R)}$. The Total FAN-Regen$^{(R)}$ was developed for non-specialists to carry out a series of design process, viz., computational preliminary design, three-dimensional aerodynamic and aeroacoustic analyses, and design optimization, for a regenerative fan. An aerodynamic analysis of the regenerative fan was conducted by solving three-dimensional Reynolds-averaged Navier-Stokes equations using the shear stress transport turbulence model. And, an aeroacoustic analysis of the regenerative fan was implemented in a finite/infinite element method by solving the variational formulation of Lighthill's analogy based on the results of the unsteady flow analysis. An optimum shape obtained by Total FAN-Regen$^{(R)}$ shows the enhanced efficiency and decreased sound pressure level as much as 1.5 % and 20.0 dB, respectively, compared to those of the reference design. The performance test was carried out for an optimized regenerative fan to validate the performance of the numerically predicted optimal design.

• Progress in Superconductivity and Cryogenics
• /
• v.16 no.2
• /
• pp.42-46
• /
• 2014

In this study we investigated ac transport current losses in the face to face stack for the anti-parallel current flow, and compared the electromagnetic properties with those of the single SC tape as well as those of the same stack for the parallel current path. The gap between the SC tapes in the stack varied in order to verify the electromagnetic influence of the neighbors when current flows in opposite direction, and the model was implemented in the finite element method program by the commercial software, COMSOL Multiphysics 4.2a. Conclusively speaking, the loss was remarkably decreased for the anti-parallel current case, which is attributed the magnetic flux compensation between the SC layers due to the opposite direction of the current flows. As the gap between SC tapes was increased, the loss mitigation became less effective. Besides, the current density distribution is very flat cross the sample width for the narrower gap case, which is believed to be benefit for the power electric system. These results are all in good agreement with those predicted theoretically for an infinite bifilar stack.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.18 no.3
• /
• pp.291-302
• /
• 2005

Due to the importance of the parameter in structural response, the uncertain elastic modulus was located at the center of stochastic analysis, where the response variability caused by the uncertain system parameters is pursued. However when we analyze the so-called stochastic systems, as many parameters as possible must be included in the analysis if we want to obtain the response variability that can reach a true one, even in an approximate sense. In this paper, a formulation to determine the statistical behavior of in-plane structures due to multiple uncertain material parameters, i.e., elastic modulus and Poisson's ratio, is suggested. To this end, the polynomial expansion on the coefficients of constitutive matrix is employed. In constructing the modified auto-and cross-correlation functions, use is made of the general equation for n-th moment. For the computational purpose, the infinite series of stochastic sub-stiffness matrices is truncated preserving required accuracy. To demons4rate the validity of the proposed formulation, an exemplary example is analyzed and the results are compared with those obtained by means of classical Monte Carlo simulation, which is based on the local averaging scheme.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.8
• /
• pp.757-762
• /
• 2011

We investigate the transient temperature response in biological tissue whose surface is exposed to alternately varying sinusoidal oscillation. Based on the Pennes bio-heat equation, we apply numerical analysis using a finite element method to find the effects of the physical properties of the skin layers. Three layers of tissue-epidermis, dermis, and subcutaneous-are considered as the solution region. We investigate the effects of different properties of the skin layers on the temperature profile. We also investigate the effects of the perfusion rate for the dermis, which is the most sensitive layer. The results show that the temperature profile of tissue depth has a discontinuous point when different physical properties are used.

• Journal of the Society of Naval Architects of Korea
• /
• v.30 no.3
• /
• pp.29-40
• /
• 1993

The fundamental characteristics of nonlinear free-surface waves generated by a shallowly submerged 3-dimensional hydrofoil are investigated. The fluid is assumed inviscid, incompressible and its motion irrotational. The surface tension on the free-surface is neglected. The hydrofoil is represented by a horseshoe vortex system whose shape is assumed fixed. Also the strengths of vortices are assumed given. The exact problem for the wave potential due to the horseshoe vortex system is formulated by the variational principle based on the classical Hamilton's principle. The localized finite element method is used in the numerical computations. In order to increase the numerical efficiency, an intermediate nonlinear-to-linear transition buffer subdomain for a smooth matching is introduced between the fully nonlinear computation subdomain and the truncated linear infinite subdomain. Also used is the modal analysis to reduce the computation tome drastically. The effect of inflow velocity, submergence depth of the hydrofoil and the shape of circulation distribution on the wave profiles are thoroughly examined. Especially it was possible to investigate the nonlinear influence of the free vortex on the free vortex. The nonlinear free-surface effect on the induced forces on the hydrofoil is also investigated.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.6
• /
• pp.137-146
• /
• 2005

299 railroad slopes were investigated and the failure characteristics and reinforcement patterns were analyzed. Stability analyses on the 14 cut-off soil slopes were carried out. Surficial failures were predicted by infinite slope analyses assuming the temporarily perched ground water table at soil surface during rainfall period. Limit equilibrium analyses were also carried out and the influences of rainfall infiltration on the slope stabilities were taken Into account by seepage analyses using finite element method and by assuming ground water tables to be located adjacent to soil surface. The adequacy of those analyses was evaluated by comparing the slope failure characteristics between analysis results and the past failure records. From the comparison results, it was deduced that the limit equilibrium analyses were not appropriate to estimate the shallow failure that occurred at most of the railroad cut-off soil slopes. For the better estimation of the surficial failure, not only the increase of pore-water pressure (reduction of matric suction), but also the influence of water flows over slope surface which erode soil mass, should be evaluated and considered.