• 자원환경지질
• /
• 제27권5호
• /
• pp.469-477
• /
• 1994

Many researchers have investigated most representative sequential extraction method using various reagents for determining the chemical forms of metals in soils and sediments. In this paper, a newly modified method for sequential extraction scheme based on Tessier's method by Environmental Geochemistry Research, Centre for Environmental Technology, Imperial College, was introduced and examined. In comparison with Tessier's method, originally designed for sediment analysis by Atomic Absorption Spectrophotometry (AAS), the sequential extraction scheme has been developed for the multi-element analysis by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES). The partitioning of particulate trace elements was classified into five fractions: (i) exchangeable, (ii) bound to carbonates or specially adsorbed, (iii) bound to Fe and Mn oxides, (iv) bound to organic matter and sulphides and (v) residuals. The experimental results of the pilot study for in-house reference material (HRM2) and certified international standard reference material (SRM2711) using the modified method showed not only reasonable precision and accuracy but also acceptable overall recovery rates. In addition, mine dump soils sampled in the Dalsung Cu-W mine, Korea were prepared and sequentially extracted using the method. Most of Cu was bound to organic matter/sulphides and residual fractions. The dominant fraction of soil Pb and Zn in the study area was found in the residuals. The fraction of Cd showed a wide variation between samples and could be found bound to the carbonates or specially adsorbed, oxides, organic fraction and residuals. The recovery rates of Cd, however, were poor due to relatively low Cd concentrations in soils. The heavy metals in these mine dumps appear to be in the more inert forms and should not be readily bioavailable. The soils, however, had very low pH values (average 4.1) and had sandy textures; consequently, rapid infiltration of rainfall may increase leaching of Zn and Cd which were found to be around 5 to 10% of the exchangeable fraction. As a result of the investigation of this study, it has been strongly recommended that these mine waste materials should still be considered a significant contaminant source and will need environmental remediation to prevent pollutants from being released into the environment.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.389-389
• /
• 2012

Molybdenum is one of the most important materials used as a back ohmic contact for $Cu(In,Ga)(Se,S)_2$ (CIGS) solar cells because it has good electrical properties as an inert and mechanically durable substrate during the absorber film growth. Sputter deposition is the common deposition process for Mo thin films. Molybdenum thin films were deposited on soda lime glass (SLG) substrates using direct-current planar magnetron sputtering technique. The outdiffusion of Na from the SLG through the Mo film to the CIGS based solar cell, also plays an important role in enhancing the device electrical properties and its performance. The structure, surface morphology and electrical characteristics of Mo thin films are generally dependent on deposition parameters such as DC power, pressure, distance between target and substrate, and deposition temperature. The aim of the present study is to show the resistivity of Mo layers, their crystallinity and morphologies, which are influenced by the substrate temperature. The thickness of Mo films is measured by Tencor-P1 profiler. The crystal structures are analyzed using X-ray diffraction (XRD: X'Pert MPD PRO / Philips). The resistivity of Mo thin films was measured by Hall effect measurement system (HMS-3000/0.55T). The surface morphology and grain shape of the films were examined by field emission scanning electron microscopy (FESEM: Hitachi S-4300). The chemical composition of the films was obtained by the energy dispersive X-ray spectroscopy (EDX). Finally the optimum substrate temperature as well as deposition conditions for Mo thin films will be developed.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2014년도 추계학술대회 논문집
• /
• pp.212-212
• /
• 2014

0.04% Gd-duplex stainless steels (Gd-DSTSs) for neutron absorbing materials were inert arc-melted and poured into a Y-shape block with the size of $100{\times}100{\times}20[mm]$. The Gd-DSTS was hot rolled at $1200^{\circ}C$ followed by cold rolling to have 33% reduction. The average grain sizes of the rolling (RD), transverse (TD) and short transverse (ST) directions were 6, 7, $11{\mu}m$, respectively. The micro-hardnesses of the RD, TD and ST directions were 258.5, 292.3, 314.7 $H_V$, respectively. Corrosion potential and corrosion rate of the cold rolled Gd-duplex stainless steel in aerated artificial sea water and 0.1M $H_2SO_4$ solution were $0.2216V_{SHE}$, $0.0106A/cm^2$, $-0.0825V_{SHE}$, $0.0168A/cm^2$ for RD, $0.2210V_{SHE}$, $0.0077A/cm^2$, $0.0817V_{SHE}$, $0.0092A/cm^2$ for TD, $0.1056V_{SHE}$, $0.0059A/cm^2$, $0.0475V_{SHE}$, $0.0069A/cm^2$ for ST, respectively. The corrosion behavior depended on the texture, which were due to mainly grain boundary and minorly crystallographic texture. Friction coefficient and wear resistance were 2.07 and 0.48 mm, respectively.

• Composites Research
• /
• 제26권2호
• /
• pp.129-134
• /
• 2013

극저온 환경에 노출되는 구조체의 접착조인트의 경우 피접착물과 접착물 사이에서 열팽창계수 차이로 인해 계면에서 잔류응력이 발생하게 되는데 이에 의해 접착조인트 내부에 미소균열, 층간분리 등의 형태로 파손이 발생할 우려가 있다. 본 연구에서는 높은 비강성, 낮은 열팽창계수의 특성을 지닌 메타 아라미드 섬유를 에폭시 기지재의 보강재로 사용하였다. 표면처리 공정을 간소화하기 위해 전기방사법의 고분자 혼합법(polymer blend method)으로 코어-쉘 구조의 메타 아라미드/에폭시 나노섬유를 제조하였다. 극저온 환경에서 계면특성이 향상된 코어-쉘 구조의 나노섬유를 보강한 에폭시 접착제의 전단물성을 확인하기 위해 환경챔버를 이용하여 $-150^{\circ}C$의 저온에서 단일 겹치기 실험(single lap joint test)을 진행하였다. 또한, DCB(double cantilever beam) 실험을 통해 파괴인성을 측정하였다. 그 결과, 극저온에서 일반 메타 아라미드 나노섬유에 비해 코어-쉘 구조의 메타 아라미드/에폭시 나노섬유를 보강한 접착제 시편이 우수한 계면특성으로 인해 물성이 크게 향상되었음을 확인하였다.

• 한국결정성장학회지
• /
• 제10권5호
• /
• pp.362-366
• /
• 2000

$Li_{0.44}MnO_2$양극재료는 리튬의 삽입과정에서 높은 가역성을 가지며 과충전이나 과방전 과정에서 쉽게 손상되지 않는다. $Mn_2O_3$가 불순물로 자주 나타나며 전기화학적으로 비활성이기 때문에 전극의 전기화학적 용량을 감소시킨다. 잉여의 NaOH 첨가는 $Mn_2O_3$를 X선 회절에 검출되지 않는 정도로 낮추었다. 용량 증가는 큰 단위세포를 가지는 양극재료에서 얻어질 수 있으므로, 망간의 일부를 이온반경이 큰 티타니움으로 치환하였으며, $Li_{0.44}T_{iy}Mn_{1-y}O_2$(여기서 y = 0.11, 0.22, 0.33, 0.44, 0.55) 조성의 분말들을 합성하여 특성을 평가하였다. ECPS 실험결과 $Li/P(EO)_8$LiTFSI/$LixTi_{0.22}Mn_{0.78}O_2$전지에서 150 mAh/g 최대가역용량 값이 얻어졌다. 티타니움이 치환된 망간산화물을 사용한 전지는 충방전당 0.12 %나 그 이하의 용량감소율을 나타내었다.

• 한국환경과학회지
• /
• 제1권1호
• /
• pp.41-46
• /
• 1992

주거지역에서 대기오염물 시료채취에 대한 장기간 연구를 수행하기 위해서 휘발성 유기 화합물 분석에 적합한 24시간동안의 종합적인 공기시료를 채취하기 위해 공기시료 채취기가 제작되었다. 이 시료 채취기는 시료채취시 요구되는 모든 특성을 포함할 뿐만 아니라, 일반가정에 근접해서 설치되어야하므로 심미적 특성도 포함한다. 이 공기시료 채취기는 흡착제(티넥스)로 채워진 5/8인치 외경의 스테인레스 스틸 트랩 네개를 수용할수 있고, 분당 5-50 밀리리터의 범위에서 네 종류의 공기유속을 이용할수 있게 고안 되었다. 금속필도(10마이크로미터)가 트랩 어댑터의 입구에 직접 부착되었다. 부가적인 특성은 다음과 같다. : 1) 유기물질에 불활성인 재료로 제작 되었고, 2) 날씨에 영향을 받지 않고, 3) 전지를 이용하고, 4) 사람의 호흡영역에서 공기 시료를 채취하고, 그리고 5) 방음제로 싸여진 작은 펌프를 이용하여 조용하게 작동된다. 펌프/전지 장치는 시료채취기의 본체로부터 분리 되었다. 이 장치로 부터 야기되는 소음수준은 주거지역의 허용기준치(뉴저지주 환경보호국 기준)보다 낮았다. 이 공기시료 채취기는 일상 주거지역과 단층의 한 국민학교 옥상에서 성공적으로 작동되었다.

• 한국군사과학기술학회지
• /
• 제16권6호
• /
• pp.857-866
• /
• 2013

This paper is concerned with the material properties of functional high explosive(FHX) simulant at various strain rates ranging from $10^{-4}/sec$ to $10^1/sec$. Material properties of FHX at high strain rates are important in prediction of deformation modes of FHX in a warhead which undergoes dynamic loading. Inert FHX stimulant which has analogous mechanical properties with FHX was utilized for material tests due to safety issues. Uniaxial tensile tests at quasi-static strain rates ranging from $10^{-4}/sec$ to $10^{-2}/sec$ and intermediate strain rates ranging from $10^{-1}/sec$ to $10^1/sec$ were conducted with JANNAF specimen using a tensile testing machine, INTRON 5583, and developed high speed material testing machine, respectively. Uniaxial compressive tests at quasi-static strain rates and intermediate strain rates were conducted with cylindrical specimen using a dynamic materials testing machine, INSTRON 8801. And cyclic compressive loading tests were performed with various strain rates and strains. Deformation behaviors were investigated using captured images obtained from a high-speed camera.

• Bulletin of the Korean Chemical Society
• /
• 제17권7호
• /
• pp.637-642
• /
• 1996

Preparation and properties of potential CVD (Chemical Vapor Deposition) precursors for the TiO2, a major component of the perovskite materials such as PT, PLT, PZT, and PLZT were investigated. Reactions between β-diketones and TiMe3, formed in situ failed to produce stable Ti(β-diketonate)3 complexes but a stable purple solid, characterized as (OTi(BPP)2)2 (BPP=1,3-biphenyl-1,3-propanedione) was obtained when BPP was used. Several new Ti(Oi-Pr)2(β-diketonate)2 complexes with aromatic or ring substituents were synthesized by the substitution reaction of Ti(OiPr)4by β-diketones and characterized with 1H NMR, IR, ICP, and TGA. Solid complexes such as Ti(Oi-Pr)2(BAC)2 (BAC=1.-phenyl-2,4-pentanedione), Ti(Oi-Pr)2(BPP)2, Ti(Oi-Pr)2(1-HAN)2 (1-HAN=2-hydroxy-1-acetonaphthone), Ti(Oi-Pr)2(2-HAN)2 (2-HAN=1-hydroxy-2-acetonaphthone), Ti(Oi-Pr)2(ACCP)2 (ACCP=2-acetylcyclopentanone), and Ti(Oi-Pr)2(HBP)2 (HBP=2-hydroxybenzophenone) were found to be stable toward moisture and air. Ti(Oi-Pr)2(ACCP)2 and Ti(Oi-Pr)2(HBP)2 were proved to have lower melting points and higher decomposition temperatures. However, these complexes are thermally stable and pyrolysis under an inert atmosphere resulted in incomplete decomposition. Ti(Oi-Pr)2(DPM)2 (DPM=dipivaloylmethane) and Ti(Oi-Pr)2(HFAA)2 (HFAA=hexafluoroacetylacetone) were sublimed substantially during the thermal decomposition. Pyrolysis mechanism of these complexes are dependent on type of β-diketone but removal of Oi-Pr ligands occurs before the decomposition of β-diketonate ligands.

• Environmental Engineering Research
• /
• 제24권3호
• /
• pp.463-473
• /
• 2019

Nanoscale zero-valent iron (nZVI) has proved to be an effective tool in applied environmental nanotechnology, where the decreased particle diameter provides a drastic change in the properties and efficiency of nanomaterials used in water purification. However, the agglomeration and colloidal instability represent a problematic and a remarkable reduction in nZVI reactivity. In view of that, this study reports a simple and cost-effective new strategy for ultra-small (< 7.5%) distributed functionalized nZVI-EG (1-9 nm), with high colloidal stability and reduction capacity. These were obtained without inert conditions, using a simple, economical synthesis methodology employing two stabilization mechanisms based on the use of non-aqueous solvent (methanol) and ethylene glycol (EG) as a stabilizer. The information from UV-Vis absorption spectroscopy and Fourier transform infrared spectroscopy suggests iron ion coordination by interaction with methanol molecules. Subsequently, after nZVI formation, particle-surface modification occurs by the addition of the EG. Size distribution analysis shows an average diameter of 4.23 nm and the predominance (> 90%) of particles with sizes < 6.10 nm. Evaluation of the stability of functionalized nZVI by sedimentation test and a dynamic light-scattering technique, demonstrated very high colloidal stability. The ultra-small particles displayed a rapid and high nitrate removal capacity from water.

• 한국산학기술학회논문지
• /
• 제20권2호
• /
• pp.385-393
• /
• 2019

라디칼 회분식 반응 공정을 사용하는 있는 중 소규모 화학공장의 경우, 취급 물질, 작업 내용 및 제품 등의 여러가지 상황 변화에 따른 잠재적인 화재, 폭발 및 안전의 위험성이 상존해 있다. 이러한 화학공장에서 마주치는 잠재적인 위험성에 대하여, 정성적인 위험성 평가 및 분석을 위하여 대표적으로 많이 사용되는 평가 방법인 HAZOP 기법을 이용하여 위험성 평가 연구를 진행하였으며, 이를 바탕으로 피해 크기를 최소화할 수 있는 방안을 모색하였다. 이를 위하여 국내의 중소화학 공장 중, 라디칼 회분식 반응 공정에 의하여 아크릴 수지를 생산하는 중 소규모의 화학공장을 선택하여 현장 설비, 배관 계장도 및 공정에 대하여 HAZOP 기법의 절차에 따라 위험성 평가 및 분석을 진행하였다. 연구의 결과로서, 위험성을 예방하기 위한 구체적인 조치로서는 불활성기체의 투입 및 압력 게이지 설치가 반드시 필요하며, 또한 반응 개시제와 모노머는 따로 분리하고, 폭주반응을 막기 위한 반응억제 물질과 설비를 추가로 설치하는 것이 반드시 필요함을 도출할 수 있었다.