• Journal of the Korean Society for Precision Engineering
• /
• v.5 no.4
• /
• pp.48-58
• /
• 1988

This study was undertaken to observe the formation behavior of ferro- magnetic phase in Mn-Al-Cu Alloys. The alloy selected for this investigation was 70% Mn-29% Al-1% Cu. This pre-allyed pig was prepared to the cylinderical castings using an Induction furnace after homogenizing at $1100^{\circ}C$ for 2hr, the specimens were cooled by cooling methods. Subwequent isothermal heat treatments were followed at $550^{\circ}C$ for various periods of time at predetermined(1-1000min). The formation behavior of ferromagnetic phase was investigated by measurements of magnetic properties of the specimens at each stage of heat treatment, and optical microscopic esamination and X-Ray diffraction analyses were also employed. By this basic experimental results, the conclusions are as follows 1) In order to obtain much amount of ferromagnetic phase, the optimum average cooling rate was about 7.35-$16.4^{\circ}C$/sec($1100^{\circ}C$-$600^{\circ}C$). 2) We verified the decomposition of {\tau} phase to {\beta} -Mn and {\gamma} , as the specimens were homogenized at $1100^{\circ}C$ for 12hr, then heat-treased at $550^{\circ}C$ for 1-1000min. 3) A condition of optimum heat treatments in Mn-Al-Cu permanent mag-netic alloys showed that after homogenizing at $1100^{\circ}C$ for 2hr, the speciments were cooled in air or furnace(A) and subsequent heat treatments at $550^{\circ}C$ for 1-30min. The maximum magnetic properties were measured as follows: Air cooling; Br=1200(Gause), bHc=100(oe), (BH)max=0.07(MGOe) Furnace cooling(A);Br=950(Gauss), bhe=80(Oe), (BH)max=0.05(MGOe)

• Korean Journal of Veterinary Research
• /
• v.29 no.3
• /
• pp.373-381
• /
• 1989

The aim of the present study was to test the efficiency of estrous induction in the premature, metestrous and anestrous bitches. The estrus was induced with prostaglandin $F_{2{\alpha}}$, estradiol-$17{\beta}$, pregnant mare serum gonadotropin (PMSG) and human chorionic gonadotropin(HCG) in the treatment A, and with PMSG and HCG in the treatment B. Day 0 was the first day of estrone injection in the treatment A and the day of PMSG injection in the treatment B. Twenty three of the twenty six bitches were laparotomized under general anesthesia between 11 and 18 days after onset of behavioral estrus, whereas three bitches were not laparotomized and remained until parturition. Ovarian responses were evaluated with the total number of corpora lutea or ovulation sites. The uterine horns were flushed with phosphate-buffered saline added heat treated canine serum(10%), the flushing media was collected into watch glass and the ova were examined under stereomicroscope. The results obtained were as follows: 1. Standing estrus was observed on the day $17.7{\pm}1.5$ after injection of estrone in the treament A, but ovarian responses were not detectable. 2. Standing estrus was observed on the day $12.2{\pm}0.2$ after injection of PMSG in the treament Band 14 of 17 bitches showed ovarian responses. Ova were recovered in 9 of the 14 bitches. 3. Ovarian responses were observed in one of the three premature bitches. two of the three metestrous bitches and all of the 11 anestrous bitches. The average number of the ova collected from 9 bitchs were $12.2{\pm}1.4$. 4. Three bitches in the treament B exhibited behavioural estrus and all of them were mated with fertile male dog, resulting the pregnancy in only one bitch. The pregnant bitch gave the birth of two pups.

• Journal of Aquaculture
• /
• v.6 no.1
• /
• pp.55-62
• /
• 1993

A tetraploid cyprinid loach, Misgurnus anguillicaudatus was induced by applying heat shock. The efficiency of inductions changed with the time of initiation of treatment and the duration of treatment. The highest incidence of tetraploid was obtained at the treatment of $41^{\circ}C$ for 3 min, 28 min after fertilization. Ploidy level was estimated by kariological examination and flow cytometric analysis. The tetraploid cyprinid loach had 4n = 100 chromosomes, while the diploid had 2n = 50. The erythrocytic volume of the tetraploid was 1.65 times larger than that of the diploid. The DNA content of the tetraploid and diploid showed 6.547 pg/cell and 3.067 pg/cell, respectively.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.11 s.242
• /
• pp.1229-1238
• /
• 2005

The objective of the present study was to investigate the efficacy of physical water treatment (PWT) technologies using different catalytic materials and an electronic anti-fouling device in the mitigation of mineral fouling in a once-through flow system with mini-channel heat exchanger. Effects of flow velocity and water hardness on the effectiveness of PWT technologies were experimentally studied. The artificial water hardness varied from 5.0 to 10 mo1/m$^{3}$ as CaCO$_{3}$. For 10 mo1/m$^{3}$ solution, fouling resistance reduced by 13-40$\%$ depending on flow velocity and types of PWT devices. On the other hand, fouling resistance reduced by 21-29$\%$ depending on the PWT devices for 5 mo11m3 solutions. The PWT device using alloy of Cu and Zn as catalyst (CM2) was slightly more effective than the others. SEM photographs of scale produced from the 10 mol/m$^{3}$ solution at 1.0 m/s indicated that calcium carbonate scales without PWT devices were needle-shaped aragonite, which is sticky, dense and difficult to remove. Scales with the PWT devices showed a cluster of spherical or elliptic shape crystals. Both the heat transfer test results and SEM photographs strongly support the efficacy of PWT technologies using catalytic materials and an electronic anti-fouling device in the mitigation of mineral fouling.

• Plant Biotechnology Reports
• /
• v.3 no.4
• /
• pp.347-353
• /
• 2009

Procedures that induce microspore embryogenesis have been described for a range of Brassica species, but embryo yield remains low for a number of genotypes. We have carried out experiments with the microspores from a weakly responsive line of B. napus to determine the culture conditions that optimize their in vitro embryogenesis by treating them with effectors of ethylene synthesis and action. The results revealed that isolated microspores subjected to an initial heat stress in a medium supplemented with inhibitors of ethylene synthesis such as AVG and $CoCl_2$ exhibited significantly increased embryo yields. This suggested that regulatory effects are exerted by the ethylene produced by the isolated microspores on the early processes of gametogenesis. As a consequence, treatment of microspores with SAM, an ethylene synthesis precursor, or with the ethylene-releasing agent ethephon, led to decreases in embryo yield. A special response to ethylene during the early stages of microspore development was finally shown to occur through experiments where isolated microspores were treated for increasing periods of time with $CoCl_2$. Collectively, our data demonstrated that the induction of embryogenesis induced by heat stress can be enhanced by inhibitors of ethylene biosynthesis.

• Journal of the Korean Magnetics Society
• /
• v.7 no.4
• /
• pp.180-185
• /
• 1997

Variations of core loss and coercivity with heat treatment condition have been studied in amorphous ribbon core specimens. All measurements were performed at 10 kHz with a maximum induction of 0.1 T. With increasing annealing time, both core loss and coercivity of core specimens decreased first, reaching minimum values, and increased thereafter. Specimen heat treated in an air showed better soft magnetic properties than those treated in Ar atmosphere. The specimens annealed under magnetic field higher than 6 Oe in radial direction showed reduced core loss and coercivity. The field annealing effects were increased with increasing cooling rate near Curie temperature of the material. The specimen annealed under an applied field in perpendicular direction of the core showed increased coercivity and decreased permeability.

• Current Research on Agriculture and Life Sciences
• /
• v.17
• /
• pp.59-63
• /
• 1999

A cDNA encoding rice chloroplast small HSP, Oshsp21, was introduced into Escherichia coli using the pET expression vector to analyze the possible function of Oshsp21 under heat stress. We compared the viability of E. coli ${\lambda}BL21$ (DE3) cells transformed with recombinant plasmid containing Oshsp21 with the control E. coli cells transformed with pET28a vector under heat stress after IPTG induction. Upon heat treatment at $50^{\circ}C$, those cells that expressed Oshsp21 showed improved viability compared with control cells. When the cell lysates from E. coli transformants were heated at $55^{\circ}C$, the amounts of proteins denatured in the control and pEhsp21-transformed cells were about 60% and 35% of total cell proteins, respectively. These results indicate that rice chloroplast small HSP function as a molecular chaperone in cells.

• Journal of the Korean Society of Safety
• /
• v.25 no.3
• /
• pp.28-33
• /
• 2010

Ni alloy steel is able to use during long time because of good acid and corrosion resistance. So, it's research has focused on developing the alternative alloy which is economically feasible. Recently, consumption of Kovar steel is gradually increased in field of the jet engine and the gas turbine because of its low thermal expansive characteristics. The specimens of Kovar steel(29%Ni-17%Co) contain 0.00%C, 0.03%C, 0.06%C, 0.10%C and 0.20%C, respectively. Ingots are manufactured by VIM(vacuum induction melting furnace) and then specimens are made by automatic hot rolling after heat treatment. Strength of Kovar steel according to carbon contents is estimated by hardness, tensile and impact test. Hardness of the 0.20%C specimen is more improved approximately 14.4% than one of base metal. Its strength increases 32.4% of a base metal, and its impact energy is also enhance 11.5%.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.99-102
• /
• 2004

In rheo forming process, slurry making is very important factor because the microstructure of slurry affects the quality of final products. To control the microstructure of slurry, slurry making by new rheo die casting was studied. In new rheocasting method, processes parameters are degree of overheat in molten metal, cooling condition, high frequency induction heating condition and cup temperature. Microstructures according to these parameters were observed. By image analysis, equivalent diameter and roundness of grain were investigated and discussed. To find out mechanical properties of grain controlled aluminum part by rheo die casting, tensile tests were carried out to the T6 heat treatment.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1307-1308
• /
• 2006

The purpose of this study was to examine the interfacial reaction between diamond grits and Ni-based, Ag-based, brazing filler metal, respectively. The morphology of the interface between diamond grits and Ni-based, filler metal exhibited a very good condition after this heat treatment. Cr-carbide and Ni-rich compounds were detected by XRD analysis in the vicinity of the interface between diamond grits and Ni-based, filler metal after vacuum induction brazing. Chromium carbide is considered to play an important role in the high bonding strength achieved between diamonds grits and the brazing alloy.