• Bulletin of the Korean Chemical Society
• /
• v.35 no.8
• /
• pp.2505-2511
• /
• 2014

Indium oxide nanocrystals ($In_2O_3$ NCs) with sizes of 5.5 nm-10 nm were synthesized by hot injection of the mixture precursors, indium acetate and oleic acid, into alcohol solution (1-octadecanol and 1-octadecence mixture). Field emission transmission electron microscopy (FE-TEM), High resolution X-Ray diffraction (X-ray), Nuclear magnetic resonance (NMR), and Fourier transform infrared spectroscopy (FT-IR) were employed to investigate the size, surface molecular structure, and crystallinity of the synthesized $In_2O_3$ NCs. When covered by oleic acid as a capping group, the $In_2O_3$ NCs had a high crystallinity with a cubic structure, demonstrating a narrow size distribution. A high mobility of $2.51cm^2/V{\cdot}s$ and an on/off current ratio of about $1.0{\times}10^3$ were observed with an $In_2O_3$ NCs thin film transistor (TFT) device, where the channel layer of $In_2O_3$ NCs thin films were formed by a solution process of spin coating, cured at a relatively low temperature, $350^{\circ}C$. A size-dependent, non-monotonic trend on electron mobility was distinctly observed: the electron mobility increased from $0.43cm^2/V{\cdot}s$ for NCs with a 5.5 nm diameter to $2.51cm^2/V{\cdot}s$ for NCs with a diameter of 7.1 nm, and then decreased for NCs larger than 7.1 nm. This phenomenon is clearly explained by the combination of a smaller number of hops, a decrease in charging energy, and a decrease in electronic coupling with the increasing NC size, where the crossover diameter is estimated to be 7.1 nm. The decrease in electronic coupling proved to be the decisive factor giving rise to the decrease in the mobility associated with increasing size in the larger NCs above the crossover diameter.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.98-98
• /
• 1999

Highly transparent and conducting tin-doped indium oxide (ITO) films were deposited on polycarbonate substrate by ion-assited deposition. Low substrate temperature (<10$0^{\circ}C$) was maintained during deposition to prevent the polycarbonate substrate from be deformed. The influence of ion beam energy, ion current density, and tin doping, on the structural, electrical and optical properties of deposited films was investigated. Indium oxide and tin-doped indium oxide (9 wt% SnO2) sources were evaporated with assisting ionized oxygen in high vacuum chamber at a pressure of 2$\times$10-5 torr and deposition temperature was varied from room temperature to 10$0^{\circ}C$. Oxygen gas was ionized and accelerated by cold hallow-cathode type ion gun at oxygen flow rate of 1 sccm(ml/min). Ion bea potential and ion current of oxygen ions was changed from 0 to 700 V and from 0.54 to 1.62 $\mu$A. The change of microstructure of deposited films was examined by XRD and SEM. The electrical resistivity and optical transmittance were measured by four-point porbe and conventional spectrophotometer. From the results of spectrophotometer, both the refractive index and the extinction coefficient were derived.

• Korean Journal of Materials Research
• /
• v.21 no.9
• /
• pp.486-490
• /
• 2011

Nano-indium-coated ZnO:In thick films were prepared by a hydrothermal method. ZnO:In gas sensors were fabricated by a screen printing method on alumina substrates. The gas sensing properties of the gas sensors were investigated for hydrocarbon gas. The effects of the indium concentration of the ZnO:In gas sensors on the structural and morphological properties were investigated by X-ray diffraction and scanning electron microscopy. XRD patterns revealed that the ZnO:In with wurtzite structure was grown with (1 0 0), (0 0 2), and (1 0 1) peaks. The quantity of In coating on the ZnO surface increased with increasing In concentration. The sensitivity of the ZnO:In sensors was measured for 5 ppm $CH_4$ gas and $CH_3CH_2CH_3$ gas at room temperature by comparing the resistance in air with that in target gases. The highest sensitivity to $CH_4$ gas and $CH_3CH_2CH_3$ gas of the ZnO:In sensors was observed at the In 6 wt%. The response and recovery times of the 6 wt% indiumcoated ZnO:In gas sensors were 19 s and 12 s, respectively.

• Korean Chemical Engineering Research
• /
• v.47 no.1
• /
• pp.105-110
• /
• 2009

IZO thin films have been deposited on poly(ethylene terephthalate) flexible substrate under varying radio frequency (rf) power, process pressure and thickness of IZO films using rf magnetron sputtering under $Ar/O_2$ gas mix. As the process pressure increased, the deposition rate was slightly increased and the transmittance showed little change, but the resistivity was increased. With increasing rf power, the great increase in deposition rate was observed but the transmittance showed a slight change only, and the resistivity was decreased. In addition, an attempt was made to find the optimal thickness of IZO films under varying the thickness of IZO films at the process conditions of 1 mTorr pressure and 90 W rf power, which showed lowest resistivity. IZO thin films with the thickness of $1,500{\AA}$ showed lowest resistivity and also showed highest transmittance around the wavelength zone of the maximum absorption. The power conversion efficiency of solar cells fabricated using various transparent electrodes with different thicknesses were measured and the solar cell with IZO electrode of $1,500{\AA}$ showed the maximum conversion-efficiency of 2.88 %.

• Journal of the Korean Vacuum Society
• /
• v.9 no.4
• /
• pp.400-405
• /
• 2000

We investigated the effect of TMIn (trimethly-indium) source depletion on InGaAs, InGaAsP and 1.55 $\mu\textrm{m}$ InGaAs/InGaAsP SMQW by using EPISON ultrasonic monitor for measuring the concentration of metalorganic/carrier gas mixtures. And the problems for the growth reproducibility in MOCVD was solved by using an EPISON ultrasonic monitor with closed-loop mode under the condition of TMIn source depletion. The saturation pressure of TMIn was dramatically decreased over consumption of 80%. In the case of bulk epilayer, Up-shifting of 300 arcsec to Ga-rich direction and FWHM broadening by a factor of two in DCXRD spectrum were observed due to the TMIn source depletion. In the case of SMQW, Up-shifting of 300 arcsec to Ga-rich direction in DCXRD spectrum and blue-shift of 40 nm in PL spectrum were observed due to the TMIn source depletion. However, good reproducibility ($\Delta\theta$<$\pm$100 arcsec) was achieved even the condition of 95% of TMIn consumption, when we used the EPISON with closed-loop mode.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.324-324
• /
• 2012

투명전도체(Transparent Conducting Oxides: TCOs)는 일반적으로 면저항이 $103{\Omega}/sq$ 이하로 전기가 잘 통하며, 가시광선영역인 380~780 nm에서의 투과율이 80% 이상이고, 3.2eV 이상의 밴드갭을 가지는 재료로써, 전기전도도와 가시광선영역에서 투과성이 높아 전기적, 광학적 재료로 관심을 받아 다년간 연구대상이 되어오고 있다. 현재 가장 널리 사용되고 있는 투명전도체(Transparent Conducting Oxides: TCOs) 소재로는 Indium Tin Oxide (ITO)가 가장 각광받고 있지만, Indium의 가격상승과 박막의 열처리를 통해 저항이 증가하는 단점을 가지고 있어 이를 대체 할 새로운 소재 개발이 필요한 상황이다. 그러므로 투명전도체 소재 개발에 있어서 가장 중요한 연구과제는 Indium Tin Oxide(ITO)의 단점을 개선시키고 안정된 고농도의 In-Zn-Sn-O(ITZO) 박막을 성장시키는 것이다. 본 연구에서는 RF스퍼터링법에 의하여 Si wafer에 In-Zn-Sn-O(IZTO)를 $350{\AA}$ 만큼 증착시키고, 1시간 동안 $300^{\circ}C$, $350^{\circ}C$, $400^{\circ}C$로 각각 열처리 하였다. 박막의 전자적, 광학적 특성은 XPS(X-ray Photoelectron Spectroscopy), REELS(Reflection Electron Energy Loss Spectroscopy)를 이용하여 연구하였다. XPS측정결과, ITZO박막은 In-O, Sn-O and Zn-O의 결합을 가지고 있고, 박막의 열처리를 통해 $400^{\circ}C$에서 Zn2p의 피크가 가장 크게 나타나는 반면 In3d와 Sn3d는 열처리를 했을 때가 Room Temperature에서 보다 피크가 작아지는 것을 확인하였다. 이는 $400^{\circ}C$에서 Zn가 표면에 편석됨을 나타낸다. 그리고 REELS를 이용해 Ep=1500 eV에서의 밴드갭을 얻어보면, 밴드갭은 $3.25{\pm}0.05eV$로 온도에 크게 변화하지 않았다. 또한 QUEELS -Simulation에 의한 광학적 특성 분석 결과, 가시광선영역인 380nm~780nm에서의 투과율이 83%이상으로 투명전자소자로의 응용이 가능하다는 것을 보여주었다.

• Clean Technology
• /
• v.21 no.4
• /
• pp.209-216
• /
• 2015

Indium-Tin-Oxide (ITO) is a material that is widely used for transparent conductive electrodes (TCEs). Indium (In), chief element of the ITO, is expected to be depleted in the near future owing to its high cost and limited reserves. To overcome the issue, ITO has to be retained by recycling redundant ITO targets after manufacturing processes. In this article, we proposed an efficient recycling way of the redundant ITO targets with investigation of the current recycling tendencies in domestic and foreign countries. As a result, it was revealed that only In is recycled from the redundant targets in domestic and Japan. As well, fabrication of TCEs is being researched with ITO nanoparticles solutions. However, since the TCEs fabricated with ITO target is superior to those with other materials, it is thought that establishment of regeneration technology of ITO itself is demanded for an efficient recycling and fabrication of ITO target.

• Korean Journal of Materials Research
• /
• v.9 no.11
• /
• pp.1055-1061
• /
• 1999

Indium Tin Oxide (ITO) films were fabricated by vacuum deposition technique and their microwave shielding properties were investigated for the application to the transparent shield material. The vacuum coating was conducted in a RF co-sputtering machine. The film composition and structure associated with the sputtering conditions (argon and oxygen pressure. substrate temperature. RF input power) were investigated for the attainment of high electrical conductivity and good transparency. The electrical conductivity of IT0 films fabricated under the optimum deposition conditions (substrate temperature : $300^{\circ}C$. Ar flow rate : 20 sccm, Oxygen flow rate : 10 sccm, In/Sn input power : 50/30 W) showed 5.6$\times10^4$mho/m. The optical transparency is also considerably good. The microwave shielding properties including the dominant shielding mechanism are investigated from the electrical conductivity, thickness and skin depth of the ITO films. The total shielding effectiveness is then estimated to be 26 dB, which provides a suggestion that the IT0 films can be effectively used as the transparent shield material.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.8
• /
• pp.591-596
• /
• 2013

Indium Zinc Tin Oxide (IZTO) thin films were developed as an alternative to Indium Tin Oxide (ITO) thin films. ITO material which has been acknowledged with its low resistivity and optical transparency of 85-90% has been used as major transparent conducting oxide (TCO) materials. However, due to the limited source, high price, and instability problems at high temperature of indium, many researches has been focused on indium-saving TCO materials. Mason Group of Northwestern University was reported to expand the solubility limit up to 40% by co-doping with 1:1 ratio of $Zn^{+2}$ and $Sn^{+4}$ ions. In this study, the properties of IZTO thin films corresponding to Zn/Sn different ratio were investigated. In addition, the effect of substrate temperature variable to the structural, optical and electrical properties of IZTO thin films was investigated.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.4
• /
• pp.400-406
• /
• 2024

Next-generation wide-bandgap semiconductors such as SiC, GaN, and Ga2O3 are being considered as potential replacements for current silicon-based power devices due to their high mobility, larger size, and production of high-quality wafers at a moderate cost. In this study, we investigate the gradual modulation of chemical composition in multi-stacked metal oxide semiconductor thin films to enhance the performance and bias stability of thin-film transistors (TFTs). It demonstrates that adjusting the Ga ratio in the indium gallium oxide (IGO) semiconductor allows for precise control over the threshold voltage and enhances device stability. Moreover, employing multiple deposition techniques addresses the inherent limitations of solution-processed amorphous oxide semiconductor TFTs by mitigating porosity induced by solvent evaporation. It is anticipated that solution-processed indium gallium oxide (IGO) semiconductors, with a Ga ratio exceeding 50%, can be utilized in the production of oxide semiconductors with wide band gaps. These materials hold promise for power electronic applications necessitating high voltage and current capabilities.