• Journal of Korea Foundry Society
• /
• v.32 no.5
• /
• pp.211-218
• /
• 2012

The effects of thickness, silicon and manganese contents on the mechanical properties of 3.3 wt%C-0.1 wt%S thin-section gray cast iron plates were investigated. The eutectic cell counts and volume fraction of pearlite in the matrix decreased with increased thickness and therefore the strength and hardness decreased with it. Even though the eutectic cell count increased with increased silicon content, the volume fraction of pearlite decreased and the strength and hardness decreased with it. The pearlite was refined more with increased manganese content and therefore the strength and hardness increased with it.

• Restorative Dentistry and Endodontics
• /
• v.37 no.3
• /
• pp.130-135
• /
• 2012

Objectives: The purpose of this study was to enhance curing light penetration through resin inlays by modifying the thicknesses of the dentin, enamel, and translucent layers. Materials and Methods: To investigate the layer dominantly affecting the power density of light curing units, resin wafers of each layer with 0.5 mm thickness were prepared and power density through resin wafers was measured with a dental radiometer (Cure Rite, Kerr). The dentin layer, which had the dominant effect on power density reduction, was decreased in thickness from 0.5 to 0.1 mm while thickness of the enamel layer was kept unchanged at 0.5 mm and thickness of the translucent layer was increased from 0.5 to 0.9 mm and vice versa, in order to maintain the total thickness of 1.5 mm of the resin inlay. Power density of various light curing units through resin inlays was measured. Results: Power density measured through 0.5 mm resin wafers decreased more significantly with the dentin layer than with the enamel and translucent layers (p < 0.05). Power density through 1.5 mm resin inlays increased when the dentin layer thickness was reduced and the enamel or translucent layer thickness was increased. The highest power density was recorded with dentin layer thickness of 0.1 mm and increased translucent layer thickness in all light curing units. Conclusions: To enhance the power density through resin inlays, reducing the dentin layer thickness and increasing the translucent layer thickness would be recommendable when fabricating resin inlays.

• Journal of Periodontal and Implant Science
• /
• v.33 no.3
• /
• pp.519-531
• /
• 2003

The aim of present investigation was to clinically measure the thickness of palatal masticatory mucosa in the hard palate as potential donor site for mucogingival surgery, to determine the relation to shape of palatal vault, form of tooth, gender, and to serve the clinical criteria t o choose the proper surgical technique. 84(mean age:25yrs) systemically and periodontally healthy volunteers participated in this study and 18 standard measurement points were defined in the hard palate, located on 3 lies which ran at different distances parallel to the gingival margin. 6 positions were designated on each of these 3 lines between the level of canine and 2nd molar and a bone sounding technique using a periodontal probe with minimal local anesthesia was utilized to assess the thickness of palatal masticatory mucosa. Student t-test was used to determine the difference in mucosal thickness between 2 groups gender, shape of palatal vault (high palatal vault vs. low palatal vault), tooth form (short-wide vs. long narrow) The result of this study were as follows: 1. Soft tissue thickness progressively increased in sites further away from the gingival margin (p<0.01). 2. Depending on position, in line a and line c the masticatory mucosal thickness increased from Ca to M2(p<0.01), but in line b the thickness increased from Ca to P2, and decreased to M1 and increased again to M2. 3. Gender did not influence the thickness of masticatory mucosa. 4. Palatal vault shape was associated with the thickness of masticatory mucosa. Thickness of low palatal vault group was thicker than high palatal group between P2 and M2 position. 5. Form of tooth did not influence the thickness of masticatory mucosa. In conclusion, palatal vault shape was associated with the thickness of masticatory mucosa. So, mucogingival surgery can be considered as a treatment modality in high palatal vault group. But, Gender and tooth form did not influence the thickness of masticatory mucosa.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1992.11a
• /
• pp.7-10
• /
• 1992

CoNiCr/Cr and CoCrTa/Cr for longitudinal magnetic recording media were. prepared on Coming 7059 glass by RF magnetron sputtering. The thickness of Cr underlayer was varied from 500 to $3000{\AA}$ and. that of magnetic layer was $700{\AA}$. Coercivity and squareness were measured using V.S.M.(vibrating sample magnetometer). The coercivity of films increased with increasing Cr thickness when the films were unannealed. The coercivity of the films annealed in a 10 mtorr vacuum increased initially with annealing time and then saturated with further increase in annealing time. The coercivity value difference between the unannealed and annealed films increased with increasing the thickness of Cr underlayer No significant change was found in squareness after anneal, regardless of Cr underlayer thickness.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2013.05a
• /
• pp.179-179
• /
• 2013

Surface resistance of electro-deposited copper with its thickness, current density and surface roughness was determined by using a 4-point probe analyzer. The copper was prepared electrochemically on 316 stainless steel substrate in copper sulfate solution at the condition of $1A/dm^2$, 298 K, and 6.5 cm-electrode distance. The surface resistance of the copper sheet in the range of $0.93-0.97{\Omega}$ increased with the copper thickness in the range of $21-70{\mu}m$. The surface resistance in the range of $0.963-1.009{\Omega}$ also increased with current density in the range of $0.5-2A/dm^2$. The increased surface resistances corresponded to 11% for thickness and 25% for current density, respectively.

• Proceedings of the KIEE Conference
• /
• 2005.10c
• /
• pp.95-97
• /
• 2005

Loss in the multi-stacked HTS wires are affected by a number of factor, such as, number of wires used in the stack, direction of external magnetic field and insulation thickness between the wire. This paper examines the effects of the insulation thickness on the magnetization loss of the multi-stacked YBCO coated conductor. Measurements of magnetization loss were performed using 4 different typo of multi-stacked wires and under various angle of external magnetic field. Test results show that loss density per unit volume increased for YBCO coated conductors when thickness of insulation increased. Loss density per unit volume decreased for YBCO coaled conductors when stacking number of tapes increased.

• Journal of ILASS-Korea
• /
• v.29 no.2
• /
• pp.75-82
• /
• 2024

In this study, the thickness of the liquid sheet formed by a splash plate nozzle at low jet velocities was measured by the direct contact method. The spatial distribution characteristics of the sheet thickness in the radial and circumferential directions, and the effects of jet velocity and liquid viscosity were analyzed. The wavy surface was observed for low viscosity water, but not for high viscosity glycerol solutions. The sheet thickness decreased as the circumferential angle or the distance from the impinging point increased. The sheet thickness increased as the liquid viscosity increased. Comparison with the theoretical predictions for two impinging jets showed some differences from the measurement results.

• Fashion & Textile Research Journal
• /
• v.16 no.1
• /
• pp.153-159
• /
• 2014

This study evaluates the changes of the subjective hand, preference, comfort and mechanical properties of tricot based artificial suede made from sea-island type micro fibers according to raising condition. The subjective hand and the preference of raised suede for jacket were rated by the 20's and 30's women experts according to raising cycles. Comfort properties were evaluated by air permeability, water vapor transmission, and thermal transmission. Mechanical properties were measured by the KES-FB system. The subjective hand of artificial suede was categorized into three hand factors: smoothness, warmness and thickness. Smoothness, warmness and thickness perception increased with raising cycles which affected hand preference and luxuriousness perception. The thickness and wale density of suede increased with the number of raising. Suede became more compact and less pliable and less stretchable due to increased fabric thickness; in addition, the surface of suede became smoother and compressive since the surface evenness of suede improved with smaller fiber fineness and an increased amount of naps covered the base fabric. Furthermore, water vapor transmission decreased and thermal insulation increased. The best raising conditions for artificial suede was four cycles in which artificial suede was preferred without changes in physical properties.

• Journal of Korea Foundry Society
• /
• v.23 no.4
• /
• pp.187-194
• /
• 2003

The effect of rare earth elements (R.E)(from 0.0 to 0.04%) on the microstructure formation and mechanical properties of thin-wall ductile iron castings were investigated. Tensile strength and hardness were decreased with an addition of up to 0.03% rare-earth elements. After addition of more than 0.03%, those were increased. Graphite nodule sizes were the finest, nodule count was the highst regardless of thickness and volume fraction of ferrite was the largest when that was 0.02%. However, the nodule count was decreased with increasing R.E. Futhermore. nodule size increased with increasing thickness and the volume fraction of ferrite decreased as that was increased. Nodularity was increased regardless of the thickness as that was increased. The castings of minium thickness up to 3 mm was possible without the formation of chill.

• Tribology and Lubricants
• /
• v.38 no.5
• /
• pp.199-204
• /
• 2022

This paper presents a numerical investigation of the influence of water molecule thickness on frictional behavior at the nanoscale using molecular dynamics simulation. Three different models, comprising water thin films of various thicknesses, were built, and indentation and sliding simulations were performed using the models. Various normal loads were applied by indenting the Si tip on the water film for the sliding simulation to evaluate the interplay between the water thin film thickness and the normal load. The results of the simulations showed that the friction force generally increased with respect to the normal load and thickness of the water thin film. The friction coefficient varied with respect to the normal load and the water film thickness. The friction coefficient was the smallest under a moderate normal force and increased with decreasing or increasing normal loads. As the water film became thicker, the contact area between the tip and water film became larger. Under well-lubricated conditions, the friction force was proportional to the contact area regardless of the water film thickness. As the normal force increased above a critical condition, the water molecules beneath the Si tip spread out; thus, the film could not provide lubrication. Consequently, the substrate was permanently deformed by direct contact with the Si tip, while the friction force and friction coefficient significantly increased. The results suggest that a thin water film can effectively reduce friction under relatively low normal load and contact pressure conditions. In addition, the contact area between the contacting surfaces dominates the friction force.