• Nuclear Engineering and Technology
• /
• v.31 no.1
• /
• pp.29-48
• /
• 1999

Local two-phase flow parameters of subcooled flow boiling in inclined annulus were measured to investigate the effect of inclination on the internal flow structure. Two-conductivity probe technique was applied to measure local gas phasic parameters, including void fraction, vapor bubble frequency, chord length, vapor bubble velocity and interfacial area concentration. Local liquid velocity was measured by Pilot tube. Experiments were conducted for three angles of inclination; 0$^{\circ}$(vertical), 30$^{\circ}$, 60$^{\circ}$. The system pressure was maintained at atmospheric pressure. The range of average void fraction was up to 10% and the average liquid superficial velocities were less than 1.3 m/sec. The results of experiments showed that the distributions of two-phase How parameters were influenced by the angle of channel inclination. Especially, the void fraction and chord length distributions were strongly affected by the increase of inclination angle, and flow pattern transition to slug flow was observed depending on the How conditions. The profiles of vapor velocity, liquid velocity and interfacial area concentration were found to be affected by the non-symmetric bubble size distribution in inclined channel. Using the measured distributions of local phasic parameters, an analysis for predicting average void fraction was performed based on the drift flux model and flowing volumetric concentration. And it was demonstrated that the average void fraction can be more appropriately presented in terms of flowing volumetric concentration.

• Ocean and Polar Research
• /
• v.26 no.3
• /
• pp.385-400
• /
• 2004

The Lago Sofia Conglomerate encased in the 2km thick hemipelagic mudstones and thinbedded turbidites of the Cretaceous Cerro Toro Formation, southern Chile, is a deposit of a gigantic submarine channel developed along a foredeep trough. It is hundreds of meters thick kilometers wide, and extends for more than 120km from north to south, representing one of the largest ancient submarine channels in the world. The channel deposits consist of four major facies, including stratified conglomerates (Facies A), massive or graded conglomerates (Facies B), normally graded conglomerates with intraformational megaclasts (Facies C), and thick-bedded massive sandstones (Facies D). Conglomerates of Facies A and B show laterally inclined stratification, foreset stratification, and hollow-fill structures, reminiscent of terrestrial fluvial deposits and are suggestive of highly competent gravelly turbidity currents. Facies C conglomerates are interpreted as deposits of composite or multiphase debris flows associated with preceding hyperconcentrated flows. Facies D sandstones indicate rapidly dissipating, sand-rich turbidity currents. The Lago Sofia Conglomerate occurs as isolated channel-fill bodies in the northern part of the study area, generally less than 100m thick, composed mainly of Facies C conglomerates and intercalated between much thicker fine-grained deposits. Paleocurrent data indicate sediment transport to the east and southeast. They are interpreted to represent tributaries of a larger submarine channel system, which joined to form a trunk channel to the south. The conglomerate in the southern part is more than 300 m thick, composed of subequal proportions of Facies A, B, and C conglomerates, and overlain by hundreds of m-thick turbidite sandstones (Facies D) with scarce intervening fine-grained deposits. It is interpreted as vertically stacked and interconnected channel bodies formed by a trunk channel confined along the axis of the foredeep trough. The channel bodies in the southern part are classified into 5 architectural elements on the basis of large-scale bed geometry and sedimentary facies: (1) stacked sheets, indicative of bedload deposition by turbidity currents and typical of broad gravel bars in terrestrial gravelly braided rivers, (2) laterally-inclined strata, suggestive of lateral accretion with respect to paleocurrent direction and related to spiral flows in curved channel segments around bars, (3) foreset strata, interpreted as the deposits of targe gravel dunes that have migrated downstream under quasi-steady turbidity currents, (4) hollow fills, which are filling thalwegs, minor channels, and local scours, and (5) mass-flow deposits of Facies C. The stacked sheets, laterally inclined strata, and hollow fills are laterally transitional to one another, reflecting juxtaposed geomorphic units of deep-sea channel systems. It is noticeable that the channel bodies in the southern part are of feet stacked toward the east, indicating eastward migration of the channel thalwegs. The laterally inclined strata also dip dominantly to the east. These features suggest that the trunk channel of the Lago Sofia submarine channel system gradually migrated eastward. The eastward channel migration is Interpreted to be due to tectonic forcing imposed by the subduction of an oceanic plate beneath the Andean Cordillera just to the west of the Lago Sofia submarine channel.

• Journal of Power System Engineering
• /
• v.12 no.4
• /
• pp.39-45
• /
• 2008

본 연구는 두 개의 경사진 다공 배플이 설치된 사각채널에서 국부 열전달향상 특성을 조사하였다. 채널은 19.8cm(W)$\times$4cm(H)의 단면적을 가지며 형상계수는 4.95이며 수력직경은 6.66cm이다. 4종류의 배플을 취급하였다. 가열 시험부에 동일한 크기, 경사각, 구멍형태의 경사 배플을 설치하였다. 경사 배플은 모두 19.8 cm의 폭, $2.55cm\times2.55cm$의 정 다이아몬드 형 구멍, 그리고 So의 경사각을 갖는다. 레이놀즈 수 범위는 23,000에서 57,000까지이다. 배플의 구멍의 수가 열전달 향상에 중요한 역할을 하였으며 구멍이 3개 인(baffle type II)가 가장 우수한 열전달 향상을 보였다.

• The Korean Journal of Petroleum Geology
• /
• v.11 no.1 s.12
• /
• pp.18-26
• /
• 2005

An occurrence of inclined heterolithic stratification (IHS) is described from a tidal point bar in a 40-m-deep distributary of the macrotidai, Han River delta, Korea. The channel bank demonstrates a convex-upward profile with intermittent presence or wave-formed scarps and terraces near the low-water level. The vertical succession of IHS is approximately 25 m thick and dips into the channel with angles reaching up to $14^{\circ}C$. The IHS overlies 15 m of trough cross-bedded sand deposited in the channel bottom. Even though the channel as a whole is ebb dominated, the preserved cross bedding is predominantly flood directed because the mutually evasive nature of the ebb and flood currents causes the point bar surface to be flood dominated. The IHS itself consists of inter-stratified fine sand, sandy silt, and silt with an fining-upward textural trend. Seasonal discharge variations of the Han River are not obvious in the deposits, because tile large size, distal location, and energetic tidal environment of the studied channel reduces the impart of river-stage fluctuations.

• Journal of Korea Water Resources Association
• /
• v.42 no.9
• /
• pp.715-724
• /
• 2009

In case of inclined crest groyne, flow constriction with water is different. Therefore, it is proper to apply to narrow channel or there is a risk of overflow with water level rising caused by installation of groynes. This study were conducted experiments on inclined crest groyne. Main factors of inclined crest groyne are angles of crests slope and changes of water level. Velocity profile around groyne was measured by LSPIV (Large Scale Particle Image Velocimetry). Flow fields around groyne were analyzed focused on main channel and recirculation area. From the results, Thalweg change has little an effect on rate length and height of recirculation rises on increasing rate length. Length of recirculation area was about 12$\sim$16 times of rate length of groyne. Maximum velocity in main channel area was measured about 1.45$\sim$2.1 times of approach velocity and has little an effect on crest angle of groyne. Back water velocity recirculation area was decreased on approach velocity. This result presents to make stable flow to bank protection.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.3
• /
• pp.281-289
• /
• 2005

An experimental study on the heat transfer and friction characteristics of a fully developed turbulent air flow in a square channel with $45^{\circ}$ inclined ribs on one, two, and four walls is reported. Tests were performed for Reynolds number ranging from 7,600 to 24,900. The pitch-to-rib height ratio, p/e, was kept at 8 and rib height-to-channel hydraulic diameter ratio, $e/D_h$, was kept at 0.0667. The heat transfer coefficient and friction factor values were enhanced with the increase in the number of ribbed walls. Results of this investigation could be used in various applications of internal channel turbulent flows involving different number of roughened walls.

• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.2
• /
• pp.275-283
• /
• 2006

Experiment and three dimensional numerical investigations of incompressible turbulent flow through square channels with one- and two-sided ribbed walls are performed to determine pressure drop and heat transfer. The CFX(version 5.7) software package is used for the computation. The ribbed walls have a $45^{\circ}$ inclined square rib. Uniform heat flux is maintained on whole inner heat transfer channel area. The numerical results coincide with experimental data that obtained for $7,600{\le}Re{\le}24.900$, the pitch-to-rib height ratio (p/e) of 8.0. and the rib height-to-channel hydraulic diameter ratio ($e/D_h$) of 0.0667. The results show that values of local heat transfer coefficient and friction factor in the channel with two-sided ribbed wall are higher than those in the channel with one-sided ribbed walls.

• Interaction and multiscale mechanics
• /
• v.4 no.1
• /
• pp.1-16
• /
• 2011

The inverse problem about the theoretical analysis of a drill string bending in a channel of an inclined bore-hole with localized geometrical imperfections is studied. The system of ordinary differential equations is first derived based on the theory of curvilinear flexible elastic rods. One can then use these equations to investigate the quasi-static effects of the drill string bending that may occur in the process of raising, lowering and rotation of the string inside the bore-hole. The method for numerical solution of the constructed equations is described. With the proposed method, the phenomenon of the drill column movement, its contact interaction with the bore-hole surface, and the frictional seizure can be simulated for different combinations of velocities, directions of rotation and axial motion of the string. Geometrical imperfections in the shape of localized smoothed breaks of the bore-hole axis line are considered. Some numerical examples are presented to illustrate the applicability of the method proposed.

• Journal of Industrial Convergence
• /
• v.9 no.1
• /
• pp.33-66
• /
• 2011

As an information-oriented society is arrived. an internet market has been developed steadily. This advance of internet market made the augmentation of purchasing clothes, and thus the fashion trade has tried to use effectively the internet marketing as a new channel of profit increasement. However, the fashion trade did not utilize efficiently an internet as a marketing mediation so far. This results from the want of coping with consumer behavior on the internet community. To answer the necessity of analysis of consumer behavior, this thesis inquires the difference of buying clothes on the internet shopping mall according to the lifestyle of consumer. Then this thesis provides the strategy of internet marketing fitted to each lifestyle for making a good profit. The inquiry was conducted to university located on Seoul, and the lifestyle of undergraduate was categorized to five groups, that is, trendy, information-inclined, economical purchase, brand-inclined, and spirit-pursuit types. This thesis analyzed the difference of consumer behavior of each type according to various factor, and presented a marketing strategy fitted to each type from these analysis results.

• Journal of Power System Engineering
• /
• v.13 no.2
• /
• pp.36-41
• /
• 2009

An experimental investigation was conducted to examine the fluid flow resistance in the rectangular channel with two inclined wire screen baffles. Two different types of wire screens; dutch weave and plain weave, were used as baffle devices in this experiment. Three kinds of baffles with different mesh specifications were made up of dutch type and four different kinds of baffles were made up of plain weave type. The stainless steel wire screen baffles were mounted on the bottom wall with varied angle inclination. Reynolds numbers were varied from 23,000 to 57,000. Results show that the mesh number of baffles plays an important role on friction factor behaviour. It is found that the baffle with the most number of meshes (type SA) has the highest fluid flow resistance.