• Tribology and Lubricants
• /
• v.20 no.6
• /
• pp.314-321
• /
• 2004

Thermal distortion of non-contacting mechanical seals with inclined rubbing surfaces is affected by friction heat between seal ring and seal seat. The circulation fluid along the inclined rubbing surfaces maintains cooling friction heat and lubrication between the sealing surfaces of mechanical seal with an inclined surface. Mechanical seals with inclined sealing surfaces may be useful for reducing the frictional heating and power loss because of the introduction of cooling fluids to the sealing gap between seal ring and seal seat. From the FEM computed result shows that the thermal behavior and von Mises stress of sealing faces with an inclined angle 60 are much reduced in comparison of the conventional mechanical face seal with rectangular sealing surfaces.

• PNF and Movement
• /
• v.15 no.3
• /
• pp.311-316
• /
• 2017

Purpose: Flatfeet are one of the risk factors of foot dysfunction and postural imbalance. The purpose of this study was to compare the limitation of stability (LOS) for the center of gravity (COG) between flatfeet and neutral feet on stable and unstable support surfaces. Methods: The study included 26 healthy, adult male participants: 14 with normal feet and 12 with flatfeet. The subjects were asked to incline the trunk maximumly to the left, right, anterior, and posterior directions and were asked to keep their feet on the floor with the knee extension. The subjects had 30 seconds of rest time between the tasks. The LOS (anterior, posterior, left, right) of COG was measured by Balance Trainer (BT4, Hur-labs, Tampere, Finland). An independent t- test was used to compare the LOS of COG between flatfeet and normal feet on stable and unstable support surfaces, respectively. Results: The LOS of the flatfeet group was generally decreased on stable support surfaces as compared to that of neutral feet, but it was not significantly different (p>0.05), while the LOS of the flatfeet group was significantly decreased compared to that of neutral feet on unstable support surfaces (p<0.05). Conclusion: This study suggested that the LOS of individuals with flatfeet may be decreased on unstable support surfaces and the postural balance of the flatfeet group may easily be disturbed on an unstable support surface.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.847-851
• /
• 1997

In the stereolithography process, the accuracy of cured shape depends on laser power, scanning speed, scanning pattern, resin characteristics etc. When three-dimensional objects are built, higher laser power gives higher building efficiency. Normally we could control scanning speed and scanning pattern, which affect curing thickness and generate volume of curl in & after building. Oligomer, Monomer and Initiator are major components. Kinds and of them decide characteristic of resin. In this paper, we deak with major facts and their characteristics for precision shape building.

• Journal of the Korean Society of Safety
• /
• v.25 no.2
• /
• pp.84-88
• /
• 2010

The main point of this study is to find ways to prevent accidents at complex linear sections in advance by improving geometric structure elements that can be considered from the designing stage. Complex linear roads are consisted of sections where straight sections connect with curved sections or sections where curved sections connect with curved sections with relatively high possibility of accidents and accidents can be reduced through improving designing elements in these sections. Therefore, this study aims to develop accident forecasting model in complex linear roads and to clarify major elements affecting traffic accidents. The results of analysis showed that the groups are divided into a group less than 355m based on curve radius of 355m, a group whose curve radius exceeds 355m and a group whose incline exceeds -0.79 and a group whose curve radius is below 355m and incline exceeds -0.79 for straight section + curved section, and for curved section + curved section, it is divided into a group whose first curved section is less than 410m based on curve radius of 410m and the first curve is turning right and a group exceeding 410m and the first curve is turning left. The major variables common in 2 models are front curve radius and curve types(left, right), road surfaces, weather.

• Journal of the Korean Vacuum Society
• /
• v.11 no.4
• /
• pp.249-255
• /
• 2002

For a formation of membrane structures, single crystal silicon wafers have been anisotropically etched with solutions of KOH and KOH-IPA. The etching rate was observed to be strongly dependent upon the etchant temperature and concentration. Mask patterns for the etching experiment was aligned to incline $45^{\circ}$on the primary flat of the silicon wafer. The different etching characteristics were observed according to pattern directions and etchant concentration. When the KOH concentration was fixed to 20 wt%, the U-groove etching shape was observed for the etching temperature of above $80^{\circ}C$, and V-groove shapes observed at below $80^{\circ}C$. Hillocks, which were generated at the etched silicon surfaces, has been decreased as the increasing of the etchant temperature and concentration.

• Korean Journal of Applied Biomechanics
• /
• v.16 no.2
• /
• pp.1-8
• /
• 2006

The purpose of this study was to evaluate normalized jerk according to shoes, slope, and velocity during walking. Eleven different test subjects used three different types of shoes (running shoes, mountain climbing boots, and elevated forefoot walking shoes) at various walking speeds(1.19, 1.25, 1.33, 1.56, 1.78, 1.9, 2, 2.11, 2.33m/sec) and gradients(0, 3, 6, 10 degrees) on a treadmill. Since there were concerns about using the elevated forefoot shoes on an incline, these shoes were not used on a gradient. Motion Analysis (Motion Analysis Corp. Santa Rosa, CA USA) was conducted with four Falcon high speed digital motion capture cameras. Utilizing the maximum smoothness theory, it was hypothesized that there would be differences in jerk according to shoe type, velocity, and slope. Furthermore, it was assumed that running shoes would have the lowest values for normalized jerk because subjects were most accustomed to wearing these shoes. The results demonstrated that elevated forefoot walking shoes had lowest value for normalized jerk at heel. In contrast, elevated forefoot walking shoes had greater normalized jerk at the center of mass at most walking speeds. For most gradients and walking speeds, hiking boots had smaller medio-lateral directional normalized jerk at ankle than running shoes. These results alluded to an inverse ratio for jerk at the heel and at the COM for all types of shoes. Furthermore, as velocity increased, medio-lateral jerk was reduced for all gradients in both hiking boots and running shoes. Due to the fragility of the ankle joint, elevated forefoot walking shoes could be recommended for walking on flat surfaces because they minimize instability at the heel. Although the elevated forefoot walking shoes have the highest levels of jerk at the COM, the structure of the pelvis and spine allows for greater compensatory movement than the ankle. This movement at the COM might even have a beneficial effect of activating the muscles in the back and abdomen more than other shoes. On inclines hiking boots would be recommended over running shoes because hiking boots demonstrated more medio-lateral stability on a gradient than running shoes. These results also demonstrate the usefulness of normalized jerk theory in analyzing the relationship between the body and shoes, walking velocity, and movement up a slope.

• Proceedings of the KACD Conference
• /
• 2008.05a
• /
• pp.246-257
• /
• 2008

The purpose of this study was to investigate the influence of various occlusal loading sites and directions on the stress distribution of the cervical composite resin restorations of maxillary second premolar, using 3 dimensional (3D) finite element (FE) analysis. Extracted maxillary second premolar was scanned serially with Micro-CT (SkyScan1072; SkyScan, Aartselaar, Belgium). The 3D images were processed by 3D-DOCTOR (Able Software Co., Lexington, MA, USA). HyperMesh (Altair Engineering. Inc., Troy, USA) and ANSYS (Swanson Analysis Systems. Inc., Houston, USA) was used to mesh and analyze 3D FE model. Notch shaped cavity was filled with hybrid (Z100, 3M Dental Products, St. Paul, MN, USA) or flowable resin (Tetric Flow, Viva dent Ets., FL-9494-Schaan, Liechtenstein) and each restoration was simulated with adhesive layer thickness ($40{\mu}m$). A static load of 200 N was applied on the three points of the buccal incline of the palatal cusp and oriented in $20^{\circ}$ increments, from vertical (long axis of the tooth) to oblique $40^{\circ}$ direction towards the buccal. The maximum principal stresses in the occlusal and cervical cavosurface margin and vertical section of buccal surfaces of notch-shaped class V cavity were analyzed using ANSYS. As the angle of loading direction increased, tensile stress increased. Loading site had little effect on it. Under same loading condition. Tetric Flow showed relatively lower stress than Z100 overall, except both point angles. Loading direction and the elastic modulus of restorative material seem to be important factor on the cervical restoration.

• Restorative Dentistry and Endodontics
• /
• v.33 no.3
• /
• pp.246-257
• /
• 2008

The purpose of this study was to investigate the influence of various occlusal loading sites and directions on the stress distribution of the cervical composite resin restorations of maxillary second premolar, using 3 dimensional (3D) finite element (FE) analysis. Extracted maxillary second premolar was scanned serially with Micro-CT (SkyScan1072; SkyScan, Aartselaar, Belgium). The 3D images were processed by 3D-DOCTOR (Able Software Co., Lexington, MA, USA). HyperMesh (Altair Engineering, Inc., Troy, USA) and ANSYS (Swanson Analysis Systems, Inc., Houston, USA) was used to mesh and analyze 3D FE model. Notch shaped cavity was filled with hybrid (Z100, 3M Dental Products, St. Paul, MN, USA) or flowable resin (Tetric Flow, Vivadent Ets., FL-9494-Schaan, Liechtenstein) and each restoration was simulated with adhesive layer thickness ($40{\mu}m$). A static load of 200 N was applied on the three points of the buccal incline of the palatal cusp and oriented in $20^{\circ}$ increments, from vertical (long axis of the tooth) to oblique $40^{\circ}$ direction towards the buccal. The maximum principal stresses in the occlusal and cervical cavosurface margin and vertical section of buccal surfaces of notch-shaped class V cavity were analyzed using ANSYS. As the angle of loading direction increased, tensile stress increased. Loading site had little effect on it. Under same loading condition, Tetric Flow showed relatively lower stress than Z100 overall, except both point angles. Loading direction and the elastic modulus of restorative material seem to be important factor on the cervical restoration.