• Transactions on Electrical and Electronic Materials
• /
• v.6 no.5
• /
• pp.229-232
• /
• 2005

Direct characterization of band alignment at chemical bath deposition $(CBD)-CdS/Cu_{0.93}(In_{1-x}Ga_x)Se_2$ has been carried out by photoemission spectroscopy (PES) and inverse photoemission spectroscopy (IPES). Ar ion beam etching at the condition of the low ion kinetic energy of 400 eV yields a removal of surface contamination as well as successful development of intrinsic feature of each layer and the interfaces. Especially interior regions of the wide gap CIGS layers with a band gap of $1.4\~1.6\;eV$ were successfully exposed. IPES spectra revealed that conduction band offset (CBO) at the interface region over the wide gap CIGS of x = 0.60 and 0.75 was negative, where the conduction band minimum of CdS was lower than that of CIGS. It was also observed that an energy spacing between conduction band minimum (CBM) of CdS layer and valance band maximum (VBM) of $Cu_{0.93}(In_{0.25}Ga_{0.75})Se_2$ layer at interface region was no wider than that of the interface over the $Cu_{0.93}(In_{0.60}Ga_{0.40})Se_2$ layer.

• Journal of electromagnetic engineering and science
• /
• v.18 no.2
• /
• pp.73-77
• /
• 2018

This paper proposes a dual-band bandpass filter using stepped-impedance resonators (SIRs) with parallel coupled structures. The proposed filter adopts U-shaped SIRs with parallel coupled lines (PCLs) that have interdigital and comb-line shorted ends. The central PCLs build an upper passband and a transmission zero, and the two U-shaped SIRs build a lower passband. Four resonators and coupling structures are theoretically analyzed to derive its scattering parameters. A novel dual-band bandpass filter is designed and fabricated using the induced scattering characteristics. The measured results show that the fabricated dual-band bandpass filter has an insertion loss of less than 1.02 dB in the lower band of 2.45 GHz and of 3.01 dB in the upper band of 3.42 GHz, and a band-to-band isolation of more than 40 dB, from 3.14 to 3.2 GHz.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.12 no.5
• /
• pp.46-51
• /
• 2013

In this paper, a dual-band antenna is proposed for the RF power harvester system as well as RFID tag. The proposed antenna operates as the passive and active RFID tag antenna in the UHF and microwave band, respectively. In addition, to charge the battery of an active RFID tag in the microwave band, it harvest the RF signal for tagging from the passive RFID tag antenna in the UHF band. The proposed antenna operates in the UHF band (917~923.5 MHz) and microwave band (2.4~2.45 GHz). In order to obtain the dual-band operation, the dipole structure and meander parasitic elements are proposed as the ${\lambda}/2$ and $1{\lambda}$ dipole antenna, respectively. The radiating dipole structure in the microwave band acts as the coupled feed for the meander parasitic elements in the UHF band. The impedance bandwidth (VSWR < 2) of the proposed antenna covers 917~923.5 MHz (UHF band) and 2.4~2.45 GHz (Microwave band). Measured total efficiencies are over 45 % in the UHF band and over 70 % in the microwave band. Peak gains are over 0.18 dBi and 2.8 dBi in the UHF and microwave band with an omni-directional radiation pattern, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.347-351
• /
• 2003

A p-$CdIn_2Te_4$ single crystal has been grown by the Bridgman method without a seed crystal in a tree-stage vertical electric furnace. From photocurrent measurements, it was found that three peaks, A, B, and C, corresponded to an intrinsic transition due to the band-to-band transition from the valence band states ${\Gamma}_7(A),\;{\Gamma}_6(B),\;and\;{\Gamma}_7(C)$ to the conduction band state ${\Gamma}_6$, respectively. Also, the valence band splitting of the $CdIn_2Te_4$ crystal has been confirmed by photocurrent spectroscopy. The crystal field splitting and the spin orbit splitting were obtained to be 0.2360 and 0.1119 eV, respectively. Also, the temperature dependence of the band gap energy of the $CdIn_2Te_4$ crystal has been driven as the following equation of $E_g(T)\;=E_g(0)\;-\;(9.43\;{\times}\;10^{-3})T^2/(2676\;+\;T)$. In this equation, the Eg(0) was estimated to be 1.4750, 1.7110, and 1.8229 eV at the valence band state A, B, and C, respectively. The band gap energy of the p-$CdIn_2Te_4$ at room temperature was determined to be 1.2023 eV.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.6
• /
• pp.1397-1403
• /
• 2011

In this paper, fabrication of sample holder was studied for an analysis of electromagnetic(EM) wave property in W-band(75 GHz~110 GHz). First of all, a propagation theory of EM wave was considered in the rectangular waveguide, and measurement technique was suggested for analysis of characteristics. A sample holder using in W-band was designed and fabricated, and used for analysis of material property and absorption ability using RAM samples. As a result, the sample holder test was verified exactly for measuring EM wave property of RAM sample. In the future, the proposed sample holder would like to be used for the EM wave property analysis in W-band.

• Geomechanics and Engineering
• /
• v.5 no.6
• /
• pp.499-517
• /
• 2013

In order to investigate shear behavior of granular materials due to excavation and associated unloading actions, load-controlled plane strain compression tests under decreasing confining pressure were performed under drained conditions and the results were compared with the conventional plane strain compression tests. Four types of granular material consisting of two quartz sands and two glass beads were used to investigate particle shape effects. It is clarified that macro stress-strain behavior is more easily influenced by stress level and stress path in sands than in glass beads. Development of localized deformation was analyzed using photogrammetry method. It was found that shear bands are generated before peak strength and shear band patterns vary during the whole shearing process. Under the same test condition, shear band thickness in the two sands was smaller than that in one type of glass beads even if the materials have almost the same mean particle size. Shear band thickness also decreased with increase of confining pressure regardless of particle shape or size. Local maximum shear strain inside shear band grew approximately linearly with global axial strain from onset of shear band to the end of softening. The growth rate is found related to shear band thickness. The wider shear band, the relatively lower the growth rate. Finally, observed shear band inclination angles were compared with classical Coulomb and Roscoe solutions and different results were found for sands and glass beads.

• Journal of electromagnetic engineering and science
• /
• v.17 no.4
• /
• pp.233-237
• /
• 2017

In this paper, a dual-band high frequency (HF) and ultra-high frequency (UHF) radio-frequency identification (RFID) tag antenna is presented that operates in the 13.56 MHz band as well as in the 920 MHz band. A spiral coil along the edges of the antenna substrate is designed to handle the HF band, and a novel meander open complementary split ring resonator (MOCSRR) dipole antenna is utilized to generate the UHF band. The dual-band antenna is supported by a single-feeding port for mono-chip RFID applications. The antenna is fabricated using an FR4 substrate to verify theoretical and simulation designs, and it has compact dimensions of $80mm{\times}40mm{\times}0.8mm$. The proposed antenna also has an omnidirectional characteristic with a gain of approximately 1 dBi.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.533-534
• /
• 2008

This paper presents a multi-phase ring VCO for low-cost, low-power GPS receiver. In the RF band used in GPS, L1 band is now in commercial-use and L2,L5 are predicting to be commercial-use soon. Thus Wide band PLL and Cost-effective IC solutions are required for future multi-band GPS receiver that received three types band at once. A new PLL architecture for multi-band GPS application is proposed. Ring VCO is even smaller than LC-VCO and a good alternative for low-cost solution. Proposed multi-phase ring VCO offers wide frequency range covering L1, L2, and L5 band, 20% reduction of area, 23% reduction of PLL power and can generate I/Q without extra I/Q generator.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.9
• /
• pp.924-929
• /
• 2009

In this paper, a dual-band MIMO antenna with a band stop matching circuit for next generation USB dongle application is proposed. The proposed multiband MIMO antenna consists of two dual-band PIFAs which provide wideband characteristics. In order to improve the isolation characteristic at the LTE(Long Term Evolution) band, a band stop matching circuit was inserted at the corner of each antenna element. The inserted band stop matching circuit is to suppress the surface current at the specific frequency band and to generate two additional resonances around 770 MHz for LTE band and near 830 MHz for digital communications network(DCN) service. The proposed MIMO antenna can cover LTE and DCN services, simultaneously.

• Journal of electromagnetic engineering and science
• /
• v.16 no.1
• /
• pp.19-23
• /
• 2016

This paper presents a novel design for dual-band bandpass filters. The proposed filters are applicable to the carrier aggregation of the TV white space (TVWS) band and long-term evolution (LTE) band for cognitive radio applications. The lower passband is the TVWS band (470-698 MHz) whose fractional bandwidth is 40 %, while the higher passband is the LTE band (824-894 MHz) with 8 % fractional bandwidth. Since the two passbands are located very close to each other, a transmission zero is inserted to enhance the rejection level between the two passbands. The TVWS band filter is designed using magnetic coupling to obtain a wide bandwidth, and the LTE band filter is designed using dielectric resonators to achieve good insertion loss characteristics. In addition, in the proposed design, a transmission zero is placed with cross-coupling. The proposed dual-band bandpass filter is designed as a two-port filter (one input/one output) as well as a three-port filter (one common input/two outputs). The measured performances show good agreement with the simulated performances.