• 대한기계학회논문집A
• /
• 제33권9호
• /
• pp.903-912
• /
• 2009

This study is focused on simulation-based dimensional tolerance optimization process (DTOP) to minimize vehicle pulls by reduction of dimensional variation in front suspension system. In previous studies, the effect of tires and wheel alignment sensitivity have mainly been investigated to eliminate vehicle pulls in nominal design condition without allocating optimal tolerance level for selected components, among various factors regarding vehicle pulls such as vehicle design parameters, vehicle weight balance, tires, and environmental factors. Unfortunately, there are wide variations in the real vehicle, and these have impacted actual vehicle pulls, especially wheel alignment effects from suspension geometry variation has not been considered in the previous studies. In the tolerance design of suspension, tolerance variables with the uncertainty such as parts dimensional variation, assembly process, datum position and direction, and assembly tool tolerance has a great influence on the variation of the suspension dimensional performances. This study introduces total vehicle pull prediction model in considering major key factors for vehicle pull sensitivity. The Monte Carlo-based tolerance analysis model using Taguchi robust method is developed to optimize dimensional tolerance parameters, satisfying on the target variation level.

• 대한기계학회논문집A
• /
• 제26권7호
• /
• pp.1401-1407
• /
• 2002

This paper represents an investigation of the vehicle-to-vehicle distance control system using Hardware-in-the-Loop Simulation(HiLS). Control logic is primarily developed and tested with a specially equipped test vehicle. Establishment of an efficient and low cost development tool is a very important issue, and test vehicle approach is costly and time consuming. HiLS method is useful in the investigation of driver assistance and active safety systems. The HiLS system consists of a stepper motor for throttle control, a hydraulic brake system with an electronic vacuum booster, an electronic controller unit, a data logging computer which are used to save vehicle states and signals of actuator through a CAN and a simulation computer using mathematical vehicle model. Adaptation of a CAN instead of RS-232 Serial Interface for communication is a trend in the automotive industry. Since this environment is the same as a test vehicle, a control logic verified in laboratory can be easily transferred to a test vehicle.

• 자동차안전학회지
• /
• 제14권2호
• /
• pp.14-19
• /
• 2022

This paper presents motion planning algorithm that yields to intervening side lane vehicles in a congested traffic flow based on vehicle to vehicle (V2V) communication. Autonomous driving in dense traffic situation requires advanced driving performance in terms of vehicle interaction and risk mitigation. One of the most important functions necessary for congested traffic autonomous driving is to predict the lane change intention of the side lane target vehicle. However, implementing this function by using only environmental sensors has limitations. In this study, V2V communication is used to overcome the limitations and determine the intention of cut-in vehicles. Lane change intention of the intervening side lane vehicle is inferred by its longitudinal speed, steering angle, and turn signal light information received by the on-board-unit (OBU). Once the yield decision is made, the subject vehicle decelerates to generate sufficient clearance for the target vehicle to enter. Validation of the algorithm was conducted with actual autonomous test vehicles.

• 한국자동차공학회논문집
• /
• 제8권6호
• /
• pp.267-278
• /
• 2000

Vehicle dynamic models in handing and stability analysis are divided into three groups: bicycle model, roll axis model and full vehicle model. Bicycle model is a simple linear model, which hag two wheels with load transfer being ignored. Roll axis model treats left and right wheels independently. In this model, load transfer has a great effect on nonlinearity of tire model. Effects of suspension system can be analyzed by using full vehicle model, which is included suspension stroke motions. In this paper, these models are validated and compared through comparison with road test, and the effects of suspension kinematics and compliance characteristics on vehicle motion are analyzed. In handling and stability analysis, roll axis model can simulate the real vehicle motion more accurately than full vehicle model. Compliance steer has a significant effect, but the effect of suspension kinematics is negligible.

• 한국컴퓨터정보학회논문지
• /
• 제23권3호
• /
• pp.63-70
• /
• 2018

In this work, we analyze the relationship between the accumulated mileage of hybrid electric vehicle(HEV) and the data provided from vehicle parts. Data were collected while traveling over 70,000 Km in various paths. The data collected in seconds are aggregated for 10 minutes and characterized in terms of centrality, variability, normality, and so on. We examined whether the statistical properties of vehicle parts are different for each cumulative mileage interval of a hybrid car. When the cumulative mileage interval is categorized into =< 30,000, <= 50,000, and >50,000, the statistical properties are classified by the mileage interval as 82.3% accuracy. This indicates that if the data of the vehicle parts is collected by operating the hybrid vehicle for 10 minutes, the cumulative mileage interval of the vehicle can be estimated. This makes it possible to detect the abnormality of the vehicle part relative to the accumulated mileage. It can be used to detect abnormal aging of vehicle parts and to inform maintenance necessity.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제7권2호
• /
• pp.259-269
• /
• 2015

The issue of the longitudinal stability of a WIG vehicle has been a very critical design factor since the first experimental WIG vehicle has been built. A series of studies had been performed and focused on the longitudinal stability analysis. However, most studies focused on the longitudinal stability of WIG vehicle in cruise phase, and less is available on the longitudinal static stability requirement of WIG vehicle when hydrodynamics are considered: WIG vehicle usually take off from water. The present work focuses on stability requirement for longitudinal motion from taking off to landing. The model of dynamics for a WIG vehicle was developed taking into account the aerodynamic, hydrostatic and hydrodynamic forces, and then was analyzed. Following with the longitudinal static stability analysis, effect of hydrofoil was discussed. Locations of CG, aerodynamic center in pitch, aerodynamic center in height and hydrodynamic center in heave were illustrated for a stabilized WIG vehicle. The present work will further improve the longitudinal static stability theory for WIG vehicle.

• 한국측량학회:학술대회논문집
• /
• 한국측량학회 2003년도 추계학술발표회 논문집
• /
• pp.187-192
• /
• 2003

of the road would be a key index judged for a safety at the vehicle driving on the road. In Korea, as seen through a lot of documents, the vehicle driving speed is much faster compared with the design speed. The vehicle driving speed is an important element to get to know the vehicle driving characteristics. However, it is not easy to obtain the vehicle driving speed relating to vehicles' consecutive movements just merely through the presently used methods of vehicle driving speed. In consequence, this study has conducted photographing vehicle movements by use of digital moving images. Based on digital moving Images pictured, we have obtained a certain time interval frame and extracted out vehicles' coordinates and calculated vehicle speed from the firstly rectified image and the secondly rectified image. We could obtain comparatively exact results in the calculation of vehicle driving speed as errors of about 4%, as a result of comparison and verification of vehicle speed calculated from the digital moving images and the speed obtained from DGPS.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 II
• /
• pp.682-686
• /
• 2001

A fundamental structural design consideration for a vehicle is the overall vibration characteristics in bending and torsion. Vibration characteristics of a vehicle system are mainly influenced by dynamic stiffness of the vehicle body structure and material and physical properties of the components attached to the vehicle body structure. The first step in satisfying this requirement is to obtain a satisfactory dynamic model of the vehicle structure. In this paper. modeling techniques of the vehicle components are presented and the effects of the vehicle components on the vibration characteristics of the vehicle are investigated,

• Advances in Automotive Engineering
• /
• 제1권1호
• /
• pp.1-20
• /
• 2018

The aim of this study is the optimization of the parameters of interconnected Hydro-Pneumatic (HP) suspension system of a three-axle vehicle for ride comfort and handling. For HP suspension systems of equivalent vertical stiffness and damping characteristics, interconnected HP suspension systems increase roll and pitch stiffness and damping characteristics of the vehicle as compared to unconnected HP suspension systems. Thus, they result in improved handling and braking/acceleration performances of the vehicle. However, increased roll and pitch stiffness and damping characteristics also increase roll and pitch accelerations, which in turn result in degraded ride comfort performance. Therefore, in order to improve both ride comfort and vehicle handling performances simultaneously, an optimum parameter set of an interconnected HP suspension system is obtained through an optimization procedure. The objective function is formed as the sum of the weighted vertical accelerations according to ISO 2631. The roll angle, one of the important measures of vehicle handling and driving safety, is imposed as a constraint in the optimization study. Upper and lower parameter bounds are used in the optimization in order to get a physically realizable parameter set. Optimization procedure is implemented for a three-axle vehicle with unconnected and interconnected suspension systems separately. Optimization results show that interconnected HP suspension system results in improvements in both ride comfort and vehicle handling performance, as compared to the unconnected suspension system. As a result, interconnected HP suspension systems present a solution to the conflict between ride comfort and vehicle handling which is present in unconnected suspension systems.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 Proceedings of the Korea Automatic Control Conference, 11th (KACC); Pohang, Korea; 24-26 Oct. 1996
• /
• pp.334-337
• /
• 1996

This is a paper intended for initial stage of vehicle modeling and design. The needs to determine a variety of vehicle suspension parameters required for initial design has been difficult and time-consuming task. In order to facilitate a concise and efficient presentation of initial vehicle design procedure, this paper uses a mathematical model and physical geometry. Vehicle model consists of dimensions, inertias and mechanical constants. These vehicle model parameters divided into several categories : basic parameters, coefficients and constants, design specification, spring and damper, bush stiffness, stabilizer bar, suspension geometry, tire, and vehicle weights of various design condition. This paper uses a vehicle design fundamental (VDF) program running under Windows 95 graphical interface. The features of VDF will be briefly outlined in this paper.