• Computational Structural Engineering
• /
• v.3 no.2
• /
• pp.117-128
• /
• 1990

This study was intended to provide efficient algorithms for high quality postprocessing on the basis of microcomputers with limited capacity and functionality. Improved methods of postprocessing including stress contouring, internal force diagraming, and displacement animation, were proposed and implemented into a new finite element system. Visualization of three-dimensional structural behaviors was treated with special emphasis.

• Journal of Drive and Control
• /
• v.20 no.1
• /
• pp.1-7
• /
• 2023

In this study, the structural stability of the tank room of an aircraft rescue fire engine is to be studied. The tank room of the aircraft rescue fire engine is filled with fire extinguishing water and chemicals. Fire extinguishing water and chemical are filled to a capacity of about 12.5 tons and are subjected to high stress. The tank room is made of PP material with low yield stress. Structural analysis of the tank room is performed and structural weakness is analyzed. In addition, if a structural problem occurs as a result of structural analysis, an analysis simulation result is presented to derive an improved design and to show the validity of the structural stability of the tank room.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1303-1309
• /
• 2003

This paper presents the static and dynamic measurements for the strength and motion characteristics as well as the improved procedures to assess strength of wheel loaders. Two scenarios for static measurement were decided by which cylinder was actuating. The dynamic measurement was performed for two types of motion, that is, simple reciprocation of the working devices and actual working motion including traveling, digging and dumping. The measured items were stresses, cylinder pressures and strokes. Stress induced by bucket working showed higher level than that by boom working. The measured cylinder speeds were relatively superior to the design speeds. Working stress histories were thought to be closer to static rather than dynamic. A fully assembled FE model was prepared for structural analysis. In this paper, a more simple method was suggested to avoid nonlinearity caused by heave of rear frame under digging forces. Also how brake affected on structural behavior and digging force was examined closely in relation with tire pressure. It was confirmed that the overall stress level of wheel loader during turning traveling with loaded bucket was far lower than the yield stress of material.

• Journal of the Society of Naval Architects of Korea
• /
• v.43 no.2 s.146
• /
• pp.206-212
• /
• 2006

Structural reliability of electrical panels installed in naval vessels is of critical importance from structural performance viewpoint. The electrical panels may be exposed to vibration and fatigue loadings from internal and external sources as well as wave loadings which result into a crack and fracture due to the decrease of fatigue strength. It is also well known that welded joints including brackets within steel structures .such as vessels and bridges are vulnerable against such repeated loadings. This study introduces a preliminary result of the optimized shape of frame bracket consisting of electrical panels in navel vessels against fatigue loading and their fatigue life at brackets of electrical panels by means of hot spot stress and structural stress methods.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.6 no.2
• /
• pp.77-83
• /
• 1986

In this paper, an accurate model for structural analysis of frames with shear walls is introduced. Static and dynamic analysis of two example structures has been performed using the computer program SWAN which employes the newly developed 12 degrees of freedom plane stress element and the results are compared to those obtained using SAP IV. The 12 degrees of freedom element resulted in improved shear stress distribution in wall elements and bending moment in beam elements.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1998.10a
• /
• pp.306-313
• /
• 1998

Contrary to reinforced concrete frames, the beams or girders found in actual steel frames are neither hinged nor fixed at their ends. Instead, they are usually restrained by the columns to which they are attached. Here in this paper, common finite element program for plane frame stress analysis is improved by including the effect of partial fixities of the girder ends. To include the effect of partial fixities of the girder ends, Kim's modified slope-deflection equation is adopted. The stress analysis results obtained by this proposed method are then compared with Kim's example. Finally, method of choosing the most economic girder section for a multi-story frame is suggested through the examples.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.4 no.4
• /
• pp.141-148
• /
• 2000

Recently the Carbon Fiber Sheet(CFS) is widely used for strengthening damaged RC structures. Strengthening compression members such as column can increase ductility and strength due to the confinement effect. In this experiment, the behavior of concrete cylinders confined by CFS was examined. The confinement pressure is increased linearly as axial stress is increased in low axial stress, and the confinement effect of CFS was rapidly developed after near maximum axial stress, thus axial strength and ductility was improved. As the ratio of CPS is increased, concrete cylinders failed due to local fracture of CFS. The confinement effect of circular section is more efficient than that of rectangular section. And significant improvement of axial strength, axial strain, transverse strain at failure is observed in circular section. This is because in rectangular section the local fracture of CFS near corner may be occured, thus the strain efficiency ratio must be considered for RC structures with CFS.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.2 no.4
• /
• pp.201-208
• /
• 1998

To observe the confinement effects of Carbon Fiber Sheet(CFS) on the high-strength R/C short columns, Fifteen specimens with CFS were manufactured and tested under uni-axial compressive load. Major variables of this study are amount, spacing, type of CFS and amount of transverse steel. Increasing the amount of transverse steel and CFS, compressive strength and axial rigidity is improved. R/C columns with transverse steel and CFS exhibited less axial stress than columns with only CFS. From the test results, it is shown that the area confined with transverse steel and CFS is considerably important to evaluate axial stress of R/C short columns.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.825-830
• /
• 2001

Many techniques have been developed to evaluate the structural integrity for the traction motor with squirrel cage. However, the former approaches are not appropriate to our problems and there is no reliable specification for evaluation of squirrel cage motor. In this study, an improved boundary condition and the criteria for evaluation are proposed. Using 3-dimensional solid element, finite element model is generated. The number of meshes can be reduced by considering the symmetry of geometry. Stress analyses are carried out for three types of traction motors.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.4
• /
• pp.1041-1063
• /
• 2014

Some results on the hydroelasticity of ultra large container ships related to the beam structural model and restoring stiffness achieved within EU FP7 Project TULCS are summarized. An advanced thin-walled girder theory based on the modified Timoshenko beam theory for flexural vibrations with analogical extension to the torsional problem, is used for formulation of the beam finite element for analysis of coupled horizontal and torsional ship hull vibrations. Special attention is paid to the contribution of transverse bulkheads to the open hull stiffness, as well as to the reduced stiffness of the relatively short engine room structure. In addition two definitions of the restoring stiffness are considered: consistent one, which includes hydrostatic and gravity properties, and unified one with geometric stiffness as structural contribution via calm water stress field. Both formulations are worked out by employing the finite element concept. Complete hydroelastic response of a ULCS is performed by coupling 1D structural model and 3D hydrodynamic model as well as for 3D structural and 3D hydrodynamic model. Also, fatigue of structural elements exposed to high stress concentration is considered.