• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.12
• /
• pp.2374-2381
• /
• 2007

.We have studied to obtain the properly conditions about impedance matching of the SAW filter for the SPUDT type and the bidirectional transducer type later. And we have studied to obtain the SAW filter for the Slanted Finger Interdigital Transducer(SFIT), was formed on the Langasite substrate and was evaporated by Aluminum-Copper alloy and then we performed computer-simulated by simulator In case the SPUDT, we have employed that the number of pairs of the input and output IDT are 50 pairs and the thickness and the width of reflector are $5000{\AA}$ and $3.6{\mu}m$, respectively. And the of the bidirectional transducer, the width of IDT' fingers and the space between IDT' finger and reflector is $1.8{\mu}m$, respectively. Also, we have performed to series connected the SPUDT type with the bidirectional transducer type filter. The frequency response of the fabricated SAW filter has the property that the center frequency is about 190MHz and bahdwidth at the 3dB is probably 5.3MHz after when we have matched impedance. Also, we could obtain that ripple characteristics is less than 0.3dB and insert loss is probably -20dB after when we have matched impedance.

• The Journal of the Acoustical Society of Korea
• /
• v.41 no.5
• /
• pp.481-491
• /
• 2022

The active sonar transmission system consists of a transmitter that outputs an electrical signal and an underwater acoustic transducer that converts the amplified electrical signal into an acoustic signal. In general, the transmitter output characteristics are dependent on load impedance, and an underwater acoustic transducer, which is a transmitter load, has a characteristic that the electrical impedance varies largely according to frequency when driven. In such a variable impedance condition, the output of the active sonar transmission system may become unstable. Hence, this paper proposes a design and control technique of a sonar transmitter for transmitting a stable transmission signal even under variable impedance conditions of an underwater acoustic transducer in an active sonar transmission system. The electrical impedance characteristics of the underwater acoustic transducer are experimentally analyzed, and the sonar transmitter is composed of a single-phase full-bridge inverter, an LC filter, and a matching circuit. In this paper, the design and output control method of the sonar transmitter is proposed to protect the transmitter and transducer. It can secure stable output voltage characteristics even if it transmits the Linear Frequency Modulation (LFM) signal. The validity is verified through the simulation and the experiment.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.8
• /
• pp.42-50
• /
• 2007

This paper presents design methods for dual-frequency(2.4/5.8GHz) active receiving antennas. The proposed active receiving antennas are designed to interconnect the output port of a wideband antenna to the input port of an active device of High Electron Mobility Transistor directly and to receive RF signals of 2.4GHz and 5.2GHz simultaneously where the impedance matching conditions are optimized by adjusting the length of $1/20{\lambda}_0$(@5.8GHz) CPW transmission line in the planar antenna The bandwidth of implemented dual-frequency active receiving antennas is measured in the range of 2.0GHz to 3.1GHz and 5.25GHz to 5.9GHz. Gains are measured of 17.0dB at 2.4GHz and 15.0dB at 5.2GHz. The measured noise figure is 1.5dB at operating frequencies.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.4
• /
• pp.387-394
• /
• 2013

As the feature size of integrated circuits continues to decrease, the challenge of achieving an oxidation-free exposed layer after photoresist (PR) stripping is becoming a critical issue for semiconductor device fabrication. In this article, the hydrogen plasma characteristics in direct plasma and the PR stripping rate in remote plasma were studied using a $120{\Phi}$ cylindrical inductively coupled plasma source. E mode, H mode and E-H mode transitions were observed, which were defined by matching the $V_{rms}$ and total impedance. In addition, the dependence of the E-H mode transition on pressure was examined and the corresponding plasma instability regions were identified. The plasma density and electron temperature increased gradually under the same process conditions. In contrast, the PR stripping rate decreased with increasing proportion of $H_2$ gas in mixed $H_2/N_2$ plasma. The decrease in concentration of reactive radicals for the removal of PR with increasing $H_2$ gas flow rate suggests that NH radicals have a dominant effect as the main volatile product.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.6
• /
• pp.487-495
• /
• 2017

The thermal characteristics of the electrodeless lamp are one of the main factors that determine the design and performance of the lamp. The coupler changes the impedance characteristic by heat and its use temperature is usually within about $150^{\circ}C$. In this study, we observed the phenomenon when the coupler was exposed at a temperature of $150^{\circ}C$ or higher, which has not been discussed so far. Two types of coupler A and coupler B with different spacing between the inner tube and the coupler were analyzed for electrical, thermal and optical properties and deterioration characteristics with different heat and heat shielding conditions. First, the impedance of the system is obtained and used as a criterion for analyzing the electrical characteristics through it. The diameters of the two types of couplers are 1 mm, and the experimental result shows that the coupler diameter is 1 mm, which can cancel out the loss of the magnetic field strength. Therefore, based on these results, when the coupler is exposed to high temperature of about $200^{\circ}C$, the efficient design method corresponding thereto is proposed.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.11
• /
• pp.791-803
• /
• 2001

Mach-Zehnder type traveling-wave Ti：LiNb $O_3$ optical modulators were designed and fabricated. Optimum parameters of optical waveguides were calculated by means of the FDM. Design of CPW traveling-wave electrodes were performed by the FEM in the active region and by the CMM in the input/output section to obtain the conditions of MW effective index and impedance matching. From the measured S parameters, MW characteristics of the traveling-wane electrodes were extracted to be ${\alpha}_m$=0.05426 $\sqrt{f}$, $N_{eff}$=2.2025, and $Z_{c}$=39 ${\Omega}$. The calculated optical response R($\omega$) showed the 3 dB bandwidth of 10 GHz.z..

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.6
• /
• pp.640-646
• /
• 2008

Design procedure of corrugated horn antenna for the mm-wave frequency range is presented, and hybrid condition in horn is calculated. In this paper, corrugate profiles of horn which satisfy both transition to balanced hybrid condition and fabrication possibility under the mm-wave short wavelength are obtained. Electromagnetic fields inside horn and corrugation are derived by the cylindrical mode theory. Propagation characteristics in the horn are calculated by the mode impedance matching method with boundary conditions, and radiation fields are obtained by the Kirchhoff-Hyugen principle to the horn aperture fields. A mm-wave corrugated horn antenna which operates on $85{\sim}115GHz$ is fabricated by electric forming method. Measurements show that VSWR is under 1.3:1 over whole band and the half power beamwidth on radiation pattern 9.2, 9.16 and 9.02 degree on 85, 100 and 110 GHz are agree well with theoretical calculation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.2
• /
• pp.307-315
• /
• 2005

We have studied to obtain the SAW filter for the passband was formed on the Langasite substrate and was evaporated by Aluminum-Copper alloy and then we performed computer-simulated by simulator. We can fabricate that the block weighted type IDT as an input transducer of the filter and the withdrawal weighted type IDT as an output transducer of the filter from the results of our computer-simulation. Also, we have performed to obtain the properly design conditions about phase shift of the SAW filter for WCDMA. We have employed that the number of pairs of the input and output IDT are 50 pairs and the thickness and the width of reflector are 5000$\AA$ and 3.6$mu$m, respectively. Frequency response of the fabricated SAW filter has the property that the center frequency is about 190MHz and bandwidth at the 3dB is probably 8.2MHz. And we could obtain that return loss is less then 16dB, ripple characteristics is probably 4dB and triple transit echo is less then 18dB after when we have matched impedance.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.4
• /
• pp.426-435
• /
• 2013

In this paper, we propose the MIMO circular polarization feed network to enhance the communication performances from the previous $2{\times}2$ MIMO channel to $4{\times}4$ channel for Land Mobile Satellite communication system. The only possibility to extend the communication channel is to use the additional satellite because of the limitation of satellite spaces to install additional antennas. For overcoming this problems, we propose the MIMO circular polarization feed network to secure the isolation characteristics without the distant antenna space. The port isolation characteristics and each port impedance matching conditions are numerically verified and we suggest the $4{\times}4$ MIMO channel model of the proposed system and the performances are verified. The fabricated circular polarization patch antennas with the proposed feed network are measured in the reverberation chamber and 7~10 dB of diversity gain and 80 % increasement of channel capacity are obtained.

• Korean Journal of Optics and Photonics
• /
• v.15 no.5
• /
• pp.475-482
• /
• 2004

We have fabricated a LiNbO$_3$ travelling-wave optical modulator. The travelling-wave modulator consisted of M-Z(Mach-Zehnder) interferometer and CPW(Coplanar Waveguide) travelling-wave electrodes. Design of CPW electrodes were performed by SOR(Successive Over Relaxation) to obtain the conditions of Microwave effective index and impedance matching. The fabricated modulator had -3.2 dB insertion loss, and S$_{11}$ below -15 dB up to 12 GHz, S$_{21}$ better than -3 dB upto 7 GHz. It turned out that the optical response showed the 3 dB bandwidth of above 12 GHz.