• Elastomers and Composites
• /
• v.52 no.1
• /
• pp.59-68
• /
• 2017

The effect on the hydrolysis resistance properties by the addition of maleic anhydride grafted EMDM (MA-g-EPDM) and PP (MA-g-PP) to a PA66/GF composite was investigated with respect to the mechanical properties, thermal properties, and morphology. The degree of hydrolysis of the PA66/GF composite was measured using py-GC/MS analysis. When compared to the PA66/GFcomposite in MEG/water solution, the composites where MA-g-EPDM and MA-g-PP were added to PA66/GF showed a higher degree of hydrolysis resistance, impact strength, and thermal properties, whereas their tensile strength, tensile modulus, flexural strength and flexural modulus decreased. As immersion time in the solution increases, the rate of tensile strength drop of the MA-g-PP added composite appeared lower than that of the PA66/MA-g-EPDM/GF and PA66/GF composites. The py-GC/MS analysis confirmed the formation of PA66 hydrolysis reaction by products such as carboxylic acid and alkylamine with increasing immersion time.

• Fibers and Polymers
• /
• v.6 no.2
• /
• pp.127-130
• /
• 2005

Intrinsic UV reflection and fluorescence behaviors of polycarbonate, polyurethane and poly(ethylene terephthalate) films were investigated in order to characterize the interaction of water in these films. During water sorption process, UV reflection spectra of polycarbonate and polyurethane films showed little peak position changes. Fluorescence emission spectra of polycarbonate films showed red spectral shifts from 332 nm with water immersion time. This red-shifted peak could be due to phenyl-2-phenoxybenzoate, which is one of the major thermal degradation products in polycarbonate. Fluorescence peaks of polyurethane films appeared at two different positions and the ratio of these peak intensities increased with increasing immersion time. In the case of PET films, the UV reflection spectrum showed the peak intensity around 340 nm to change in response to water sorption. The fluorescence near 388 nm probably due to ground state dimer exhibited sensitivity with water sorption, when excited at 340 nm.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.585-588
• /
• 2006

This paper presents experimental results for durability performance of GFRP composite exposed to the $80^{\circ}C$ alkali solution. A total of 280 specimens for 4 types of additive and 7 cases of immersion time were prepared and tested. Additives used in this study were PVA, kaolin clay, and alumina powder. Specimens were immerged up to 30 days and tested for tensile strength for each immersion time. The results indicate that it is important to fill the inner space of GFRP composite densely to avoid the decrease of tensile strength. In this study, PVA additive showed better performance than other additives.

• The Journal of Korea Robotics Society
• /
• v.16 no.3
• /
• pp.232-237
• /
• 2021

In this research, a real-time tele-operation system for unmanned excavator using the LTE communication system is suggested. The distance between the operator and the excavator is limitless as long as the LTE communication available. The motion and video data of the excavator is synchronized using the Vehicle Control Unit (VCU) and streamed to the operator for immersion feeling. The video is played on the operator's monitor and the motion data is used to regenerate the excavator movement on the developed master platform. In general, a excavator is tele-operated using RF signal and the maximum distance for direct control is limited to within a hundred meter. In this research, the immersion tele-operation system is suggested for excavator operation within an 100ms time delay using the developed master platform, the VCU and LTE communication. A successful test run of the suggested tele-operation system has already been performed between an operator in Songpa (Seoul) and a excavator in Ansan (Gyeonggi-do) which is approximately 35 km apart.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.3
• /
• pp.321-328
• /
• 2023

This study is tried to to identify factors affecting academic achievement depending on the quality of class, learning immersion, level of academic achievement, and class type according to video production classes and real-time video classes in the on-contact learning situation due to the COVID-19 epidemic. The subjects of the study were 122 students enrolled in the nursing department at two universities. As a result of the study, the quality of the class was high in real-time video classes (t=-2.69, P=0.02), learning immersion was high in video production classes (t=1.14, P=0.28), and academic achievement was high in video production classes (t=4.24, P=0.01). Depending on the type of class, the effect on academic achievement is learning immersion in production video classes (β=.37, p<.001) has the most influence, and in real-time video classes, class quality (β=.29, p<.001) had the most influence on academic achievement. Based on the results of this study, it is suggested that it is necessary to develop a strategy for instructional design suitable for class types to improve academic achievement in an on-contact environment.

• Journal of the Korean institute of surface engineering
• /
• v.51 no.5
• /
• pp.291-296
• /
• 2018

In this study, we carried out an ultrasonic-chemical decontamination process with immersion type, reproduced in the laboratory. The corrosion damage characteristics, depending on kind of materials and ultrasonic process time, were investigated. Inconel 600, which showed lower corrosion potential and higher corrosion current density than that of STS 316, revealed severer corrosion damage and higher weight-loss rate than STS 316. Weight-loss rate of Inconel 600 increased with increasing ultrasonic process time. On the other hands, STS 316 presented a negligibly small corrosion damage, which was almost indistinguishable from visual observation. There was no effect of ultrasonic process time on the weight-loss rate of STS 316.

• Textile Coloration and Finishing
• /
• v.29 no.4
• /
• pp.211-222
• /
• 2017

In this study, we investigated the dyeing properties of the ultra-fine nylon suede non-woven fabric with Sulphur black dye regarding to the effect of dye concentrations, reducing agent contents, sodium carbonate contents, antioxidant contents, immersion temperature and exposure time in air by pad-steam process. The optimal conditions of dyeing for the ultra-fine nylon suede non-woven fabric were determined with dye concentration of 30% o.w.f., reducing agent content of $9{\sim}13g/{\ell}$, sodium carbonate content of $1{\sim}4g/{\ell}$, antioxidant content of $1{\sim}5g/{\ell}$, immersion temperature of $70^{\circ}C$, exposure time of 20 minutes in air and immersion time of 1 minute, respectively. Meanwhile, the colorfastness to washing, the colorfastness to light, and the colorfastness to perspiration for dyed ultra-fine nylon suede non-woven fabric were achieved in the range of 4-5 grades. The formaldehyde and arylamine were not detected on the ultra-fine nylon suede non-woven fabric by KC tests.

• Korean Journal of Food Science and Technology
• /
• v.28 no.6
• /
• pp.1095-1103
• /
• 1996

In order to minimize the deterioration of dried apple quality, changes of free sugar content, organic acid and ascorbic and during osmotic dehydration with sucrose at various temperature, concentration and immersion time were investigated in this study, total sugar increased as the temperature, concentration and immersion time were increased. Sucrose showed the largest change in content while fructose and glucose showed no and small changes, respectively. Large amounts of malic and fumaric acids, and small amounts of oxalic, citric, maleic and succinic acids were detected. Organic acids were high at low temperature treatment, and became higher with increasing concentration. Loss of ascorbic acid was small at the low temperature and high concentration. Effect of immersion time was negligible. Changes of free sugar, and organic and ascorbic acid followed the first-order and second-order reaction rate equations, respectively. Arrhenius equation was applied to determine the effect of temperature on reaction rate constants with high $r^2$. To predict the changes of quality, a model was established by using the optimum functions of temperature, concentration and immersion time. The model had high $r^2$ value for the quality changes during drying.

• Cartoon and Animation Studies
• /
• s.46
• /
• pp.107-128
• /
• 2017

Time is an indispensable element in creating a story. This makes comics artists use various time techniques such as prolepsis, summary, ellipsis and flashback to increase immersion in story when they create comics. This is intended to make a study on retrospective structure among various temporal structures. Retrospective structure means progress in different time sequence, and increases immersion by making readers become strained or relaxed. Besides, retrospective structure plays a role of increasing or decreasing the pace of story. The person who systematically put the retrospective structure into shape is $G\acute{e}rard$ Genette. He in his book "Narrative Discourse" classified retrospective structure into three types. These are made up of structure of analepse externes, analepse internes and analepse mixted. This makes a study on retrospective structure in narrative comics based on $G\acute{e}rard$ Genette's retrospective structure. To this end, Kang Full's webtoon was analyzed. The reason to analyze Kang Full's is that this work has storyline where things happening in parental generation is interwined with things in offspring generation, accordingly this is work suitable for studying the retrospective structure. This study is intended to examine whether three retrospective structures suggested by $G\acute{e}rard$ Genette are actually used through an analysis of , and as a result, it is intended to prove the fact that retrospective structure has an effect on immersion in work.

• Korean Journal of Food Science and Technology
• /
• v.21 no.2
• /
• pp.307-312
• /
• 1989

Internal mass transfer during osmotic dehydration of carrots in sugar solutions was examined as a function of concentration, temperature and immersion time of those solutions using moisture loss, sugar gain, molality and rate parameter. Influence of osmotic dehydration and blanching on browning reaction of vacuum dried carrots(3% MC: wet basis) was also evaluated. Increasing the concentration and temperature of sugar solutions increased moisture loss, sugar gain, molality and rate parameter. Water loss and sugar gain were rapid in first 4 min and then levelled off. The rate of sugar gain and molality changes on temperature was significant in lower concentration$(20^{\circ}\;Brix)$ compared to higher concentration$(60^{\circ}\;Brix)$. The changes of rate parameter were affected by concentration than by temperature of sugar solutions. Moisture loss during osmotic dehydration using a sugar solution $(60^{\circ}\;Brix,\;80^{\circ}C)$ with 20min immersion time was 55.7%. Effect of osmotic dehydration and blanching before vacuum dried to 3% MC(Wet basis) on browning reaction was significant. Minimum browning reaction during vacuum drying was carried out using pretreatments such as osmotic dehydration in sugar solution$(40^{\circ}\;Brix,\;80^{\circ}C)$ with 16 min immersion time(O.D.=0.09) and blanching with 12 min immersion time at $80^{\circ}C$(O.D.=0.31) compared to control(O.D.=1.59).