• Journal of the Korean Chemical Society
• /
• v.16 no.2
• /
• pp.74-79
• /
• 1972

The semiconductivity of polycrystalline $Cu_2O$ has been studied between $220^{\circ}C$ and $680^{\circ}C under partial pressures of oxygen from $4.06{\times}10^{-3}\;to\;10^{-5 }\;mmHg$. The plots of log conductivity vs 1/T at constant oxygen pressure were found to be linear, and the activation energies obtained from the slopes of these plots above the first transition point showed that the energies were greater under high oxygen pressure than under low pressure. The transition points between the stable range and the unstable range of $Cu_2O$ were found from the curves. The dependence of the semiconductivity on the $O_2$ pressure, in the above temperature range, is shown hysteresis.

• 전기의세계
• /
• v.20 no.3
• /
• pp.17-26
• /
• 1971

An experimental design of magnetic amplifiers and their characteristics in steady state are presented. A saturable reactor model having 2KVA capacity was designed, using Z-10 grain-oriented silicon steel which is commonly used in power transformers. Experimental and theoretical analysis show that the experimental results are in good agreement with the equal ampere-turns law. In addition to the saturable reactor, the self-saturated magnetic amplifiers of 0.4VA and 5VA capacity, using 50% Ni-Fe alloy cores having rectangular hysteresis loops were designed. Control characteristic curves of these amplifiers show high ampere-turn gain enough to be used for voltage controllers under load and non-contact magnetic switches of the rated capacity.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1477-1479
• /
• 2000

The annealing treatments on rf magnetron sputtered PZT($Pb_{1.05}(Zr_{0.52},Ti_{0.48})O_3$) thin films(4000${\AA}$) have been investigated for a structure of PZT/Pt/Ti/ITO coated glass. Crystallization properties of PZT films were strongly dependent on RTA(Rapid Thermal Annealing) annealing temperature and time. We were able to obtain a perovskite structure of PZT at 650$^{\circ}C$ and 10min. P-E curves of Pd/PZT/Pt capacitor demonstrate typical hysteresis loops. The measured values of $P_r$, $E_c$ were 15.8[${\mu}C/cm^2$], 95[kV/cm] respectively. Polarization value decrease about 10% after $10^9$ cycles.

• Steel and Composite Structures
• /
• v.27 no.6
• /
• pp.675-689
• /
• 2018

Buckling-restrained braces (BRBs) have received considerable attention in seismic design of various types of structures. Conventional BRBs are composed of steel core and surrounding steel tube filled with concrete. Eliminating the steel tube can be advantageous to BRB. In this study the idea of replacing the steel tube by CFRP layers in BRBs is proposed. The advantages of this type of BRB are mentioned, and its design criteria are introduced. The construction procedure of two BRB specimens is described. The specimens are uniaxially tested based on moderate, and severe earthquake levels and the performance of the specimens is investigated. The backbone curves resulted from the hysteresis curve are presented for the design proposes. The results of this study show that CFRP layers can effectively provide the expected performance of the encasing, and the proposed BRB can be considered a viable alternative to the conventional BRBs.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.721-724
• /
• 2006

In this study, particle size distribution of cement powder system were adjusted using the blast furnace slag powder, Blaine $2250cm^2/g\;and\;8300cm^2/g$, which easy to adjust particle size distribution to examine how particle size distribution of the binder has an effect on rheological properties of the cement paste. In addition, the relationship between n-value of Rosin-Rammler function and plastic viscosity were discussed. All measured flow curves represented thixotropy behavior and the hysteresis area was smaller for the more added coarse particle. When the combination was based on a ratio of $20{\sim}25vol%$ fine particles, $30{\sim}40vol%$ OPC and $40{\sim}45vol%$ coarse particles of the total volume, a high fluidity and low yield strength was achieved.

• Proceedings of the KIEE Conference
• /
• 1994.11a
• /
• pp.196-198
• /
• 1994

The dielectric and electrical properties of $Pb(Mg_{1/3}Nb_{2\3})O_3-PbTiO_3-BaTiO_3$ have been investigated. Perovskite crystalline phase of the specimens are confirmed by XRD at $1270^{\circ}C$. The curie temperature is around $40^{\circ}C$ with the amount of $BaTiO_3$ and $PbTiO_3$. Every specimens shows the slim loop hysteresis curves which is electrostrictive characteristic. The strain vs. applied voltage characteristics exhibits nonlinear relationship, and the specimen of 0.85PMN-0.125PT-0.025BT shows the largest strain.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.213-216
• /
• 2005

This paper presents force feedback control performance of a 3DOF haptic device that can be used for minimally invasive surgery (MIS). As a first step, a 3DOF electrorheological (ER) joint is designed using a spherical mechanism. And it is optimized based on the mathematical torque modeling. Subsequently, the master haptic device is manufactured by the spherical joint. In order to achieve desired force trajectories, model based compensation strategy is adopted for the ER master. Therefore, Preisach model fur the PMA-based ER fluid is identified using experimental first order descending (FOD) curves. A compensation strategy is then formulated through the model inversion to achieve desired force at the ER master. Tracking control performances for sinusoidal force trajectory are presented, and their tracking errors are evaluated.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2005.09a
• /
• pp.27-30
• /
• 2005

A nanoelectromechanical (NEM) switching device based on carbon nanotube (CNT) was investigated using atomistic simulations. The model schematics for a CNT based three-terminal NEM switching device fabrication were presented. for the CNT-based three-terminal NEM switch, the interactions between the CNT-lever and the drain electrode or the substrate were very important. When the electrostatic force applied to the CNT-lever was the critical point, the CNT-lever was rapidly bent because of the attractive foroe between the CNT-lever and the drain. The energy curves for the pull-in and the pull-out processes showed the hysteresis loop that was induced by the adhesion of the CNT on the copper, which was the interatomic interaction between the CNT and the copper.

• Structural Engineering and Mechanics
• /
• v.77 no.3
• /
• pp.407-416
• /
• 2021

Seismic isolation is one of the best-advanced methods for controlling seismic vibrations in buildings, bridges and nuclear facilities. A new Friction Multi-Layer Elastomeric Seismic Isolator (FMESI) has been modeled, analyzed and investigated by ABAQUS finite element analysis software and then, compared to real models. A number of friction cores have been used instead of the lead core therefore, some of the previous isolator problems have been almost resolved. Moreover, Studies show that the proposed isolator provides suitable initial stiffness and acceptable hysteresis behavior under different vertical and horizontal loading conditions and also internal stresses in different layers are acceptable. Also, as a result, the initial stiffness and overall area of the curves increase, as friction coefficients of the cores increase, although the frictional coefficients must be within a certain range.

• Computers and Concrete
• /
• v.32 no.5
• /
• pp.513-525
• /
• 2023

Recently, research on predicting the behavior of reinforced concrete (RC) columns using machine learning methods has been actively conducted. However, most studies have focused on predicting the ultimate strength of RC columns using a regression algorithm. Therefore, this study develops a successive machine learning process for predicting multiple nonlinear behaviors of rectangular RC columns. This process consists of three stages: single machine learning, bagging ensemble, and stacking ensemble. In the case of strength prediction, sufficient prediction accuracy is confirmed even in the first stage. In the case of displacement, although sufficient accuracy is not achieved in the first and second stages, the stacking ensemble model in the third stage performs better than the machine learning models in the first and second stages. In addition, the performance of the final prediction models is verified by comparing the backbone curves and hysteresis loops obtained from predicted outputs with actual experimental data.