• Membrane Journal
• /
• v.27 no.1
• /
• pp.60-67
• /
• 2017

Recently, the economic, social and environmental significance of the water industry is increasing significantly due to rapid global urbanization, population growth, and imbalance in demand and supply of water resulted by climate change. The type of these water industries are all different and they can be distinguished by the kinds of membranes used. Mainly, polymer materials that have excellent physical and chemical stability are used, but recently various methods of assigning hydrophilicity have been introduced due to their hydrophobic properties. In this study, hydrophilic polymers of four types were introduced into a commercially available hollow support to assign hydrophilicity. Furthermore, the morphology of the coated hollow support through FE-SEM was confirmed as well. Also the contact angle was measured to examine the degree of hydrophilicity of the coated hollow support with each polymer. Finally,.effect of different time on water permeability as well as the relationship between water permeability and hydrophilic polymers were investigated. As a result, the coating with 1 wt% of pluronic has good hydrophilicity degree, and shows the excellent water permeability without blocking the pore of the hollow fiber. Therefore, it can be concluded that the hydrophilic coating using pluronic polymer is most suitable as the water treatment.

• Journal of Environmental Science International
• /
• v.6 no.6
• /
• pp.689-696
• /
• 1997

This paper discussed effect of the surface roughness and the hydrophobicity of support material on the microbial attachment In a rotating biological contactor. The by- drophoblclty of each support material was determined by the measurement of contact angle of water and the surface roughness was measured by the surface roughness In- strument. Microorganisms have well attached on the surface of more hydrophilic support material like Nylon6 than that of the hydrophobic support material like PE. When the relatively hydrophilic surface was roughen, the microbial attachment was increased but when the relatively hydrophobic surface was roughen, the attachment was slightly In- creased because the hydrophobicity of support material was Increased by roughening the hydrophobic surface. Although both variables, the surface hydrophobicity and the surface roughness, have Influenced the microbial attachment, the influence of the surface roughness overruled that of the surface hydrophobicity. Support material whose surfaces were roughened about 1mm, 6mm and 11mm were allowed for attached 3, 7 and 24hr, but the differences of maximum and minimum attachment of each material gave nearly constant values and similar trend with time.

• Membrane Journal
• /
• v.24 no.4
• /
• pp.317-324
• /
• 2014

It is very well known that the conventional polyamide (PA) thin film composite (TFC) reverse osmosis (RO) membranes have excellent permselective properties, but their chlorine tolerance is not good enough. In this study, to improve such chlorine tolerance, microporous membranes containing hydrophilic functional groups such as -COOH were used as a support to prepare PA TFC RO membranes, employing the conventional interfacial polymerization method. Meta-phenylene diamine (MPD) and 2,6-diamine toluene (2,6-DAT) were used as diamine monomers and tri-mesoyl chloride (TMC) as an acid monomer. The membranes prepared were characterized using various instrumental analytical methods and permeation test set-up. The flux obtained from the membranes prepared so was more than $1.0m^3/m^2day$ at 800 psi of operating pressure, while the salt rejection was over 99.0%. The chlorine tolerance of them was also found to be better than that of the membrane prepared by using conventional polysulfone support without hydrophilic functional groups.

• Korean Membrane Journal
• /
• v.7 no.1
• /
• pp.19-27
• /
• 2005

PP hollow fiber membrane was hydrophilized by EVOH dip coating followed by low temperature plasma treatment and UV irradiation. EVOH coating attained high water flux without any prewetting but its stability did not guaranteed at high water permeation rate. At high water permeation rate, water flux declined gradually due to swelling and delamination of the EVOH coating layer causing pore blocking effect. However, plasma treatment reduces the swelling, which suppress delamination of the EVOH coating layer from PP support result in relieving the flux decline. Also, UV irradiation helped the crosslinking of the EVOH coating layer to enhance the performance at low water permeation rate. FT-IR and ESCA analyses reveal that EVOH dip coating performed homogeneously through not only membrane surface but also matrix. Thermogram of EVOH film modified plasma treatment and W irradiation show that crosslinking density of EVOH layer increased. Chemical modification by plasma treatment and UV irradiation stabilized the hydrophilic coating layer to increase the critical flux of the submerged membrane.

• Journal of the Korea Safety Management & Science
• /
• v.1 no.1
• /
• pp.259-272
• /
• 1999

In order to enhance the selectivity, productivity and yield of methyl fructoside, which was synthesized by enzymatic glycosylation of sucrose and methanol solution, controlling of surface property of solid support using different immobilization procedures optimized microenvironment of immobilized invertase. Silanization and polyethylene imine coating methods were adopted to give a hydrophobic and hydrophilic environment of immobilized invertase. As a result, polyethyleneimine coating method gave higher loading of enzyme, effective activity, and relative activity than silanization method, because it brought on increasing the functional density of amino group and enhancing the conservation of activity by regulating of hydrophilicity. And then, hydrophilic environment was possible to restraint the assessing of methyl fructoside molecule, which was more hydrophobic than sucrose, fructose, and glucose molecule in the reaction mixture, into .the active site of immobilizedinvertase. Consequently, hydrophilic microenvironment of immobilized invertase by polyethyleneimine coating obtained higher yield and productivity with increasing conversion than silanized and native invertase. Thus, this procedure optimized the microenvironment of immobilized invertase suitable for the enzymatic synthesis of methyl fructoside.

• Membrane Journal
• /
• v.33 no.6
• /
• pp.383-389
• /
• 2023

A high-performance forward osmosis (FO) membrane was prepared using polyethylene glycol diacrylate (PEGDA) hydrogel as a support layer. Through the UV-induced polymerization and subsequent phase separation of PEGDA, the crosslinked, hydrophilic, and porous PEGDA suppor layer was obtained. To achieve high FO flux and salt selectivity using the fabricated PEGDA support, a selective layer was synthesized via the toluene-assisted interfacial polymerization (TIP), in which toluene is used as an organic solvent. The prepared PEGDA-based FO membrane showed higher FO water flux and lower salt selectivity compared with commercial HTI membranes using 1.0 M NaCl draw solution and DI water feed solution. We propose the strategy to fabricate high-performance FO membranes utilizing supports formed with new hydrophilic materials and fabrication processes.

• Korean Journal Plant Pathology
• /
• v.10 no.4
• /
• pp.254-260
• /
• 1994

Magnaporthe grisea, a causal agent of blast, forms a specialized infection structure, an appressorium, to infect host. Hydrophobicity of contact surface and cAMP have been suggested as a primary environmental signal and a second messenger to trigger and mediate appressorium formation in this fungus, respectively. To generalize these factors in field isolates of M. girsea, twenty isolates originated from rice and other gramineous hosts were tested. Seventeen including rice and non-rice isolates formed appressoria on hydrophobic surface, but none of isolates formed appressoria on hydrophilic surface. Eighteen isolates formed appressoria on hydrophilic surface in the presence of IBMX, an inhibitor of phosphodiesterase, except two rice isolates. These results strongly support the hypothesis that appressorium formation by M. grisea is induced by hydrophobic hard surface and regulated by the endogenous level of cAMP in the cells. Understanding fungal development is not only of biological interest but provides new targets for novel disease control strategies.

• Membrane Journal
• /
• v.27 no.1
• /
• pp.92-103
• /
• 2017

In this study, electrochemical performance of the hydrophilized separator for the lithium ion battery is studied. The polyolefin based material used as the separator for the lithium ion battery is hydrophobic, and the electrolytic solution using a carbonate-based organic solvent is hydrophilic. Therefore, the polyolefin separator is hydrophilized using various hydrophilic polymers because lithium ion battery uses an aqueous electrolyte solution. In order to evaluate change of the coated separator, the performances of separator in terms of surface morphology, porosity and the wettability are investigated. Finally, the resistance and the ionic conductivity of separator coated with lithium ion are measured to evaluate the performance of lithium ion battery. Separator coated with PMVE shows good hydrophilicity and excellent ionic conductivity because the porosity of the separator is maintained. We can confirm that this property makes potential candidates for lithium ion battery.

• Membrane Journal
• /
• v.6 no.3
• /
• pp.182-187
• /
• 1996

Hydrophilic poly(acrylonitrile) [PAN] membrane with good molecular weight cut-off characteristics were prepared by using the phase inversion method. Permeability and molecular weight cut-off of the membranes were measured through the ultrafiltration test. On the surface of the PAN support membranes, poly(acrylic acid) [PAA] was deposited by dip-coating. The water permeability of the PAN support membrane had $0.17~31\textrm{mm}^3/m^{2} \cdot s \cdot Pa$, the molecular weight cut-off 42, 000~150, 000. The transport characteristics of the prepared composite membranes were significantly affected by the variation of the support membrane mophology. The permeability of the composite membrane was decreased with increasing molecular weight cut-off of the support membrane, and the separation factor was slightly changed depending on the feed concentration.

• Membrane and Water Treatment
• /
• v.5 no.3
• /
• pp.171-182
• /
• 2014

Organic compounds are adsorbed on RO/NF membranes, and the adsorption may influence the rejection of organic compounds by the membranes. Because almost RO/NF membranes are composite membranes, the results obtained by adsorption experiment with using membrane pieces are unable to avoid the influence by the support membrane. In this work, the interaction between membrane polymer and organic solutes was examined by an inverse HPLC methodology. Poly (m-phenylenetrimesoylate), the constituent of skin layer of RO/NF membranes, was coated on silica gel particles and used as a stationary phase for HPLC. When water was used as a mobile phase, almost hydrophilic aliphatic compounds were not effectively adsorbed on the stationary phase, although hydrophobic compounds were slightly adsorbed. The results indicated that the hydrophilic aliphatic compounds are useful probe solutes to examine the molecular sieving effect of a membrane. When water was used as a mobile phase, the aromatic compounds were strongly retained, and therefore $CH_3CN/H_2O$ (30/70) was used as a mobile phase. It was revealed that the adsorption of aromatic compounds was controlled by stacking between solute and polymer and was hindered by non-planar structure and substituents.