• 한국수소및신에너지학회논문집
• /
• 제27권6호
• /
• pp.753-763
• /
• 2016

High temperature sodium/sulfur battery(Na/S battery) has good electrochemical properties, but, the battery has some problems such as explosion and corrosion at al. because of using the liquid electrodes at high temperature and production of high corrosion. Room temperature sodium/sulfur batteries (NAS batteries) is developed to resolve of the battery problem. To recently, room temperature sodium/sulfur batteries has higher discharge capacity than its of lithium ion battery, however, cycle life of the battery is shorter. Because, the sulfur electrode and electrolyte have some problem such as polysulfide resolution in electrolyte and reaction of anode material and polysulfide. Cycle life of the battery is improved by decrease of polysulfide resolution in electrolyte and block of reaction between anode material and polysulfide. If room temperature sodium/sulfur batteries (NAS batteries) with low cost and high capacity improves cycle life, the batteries will be commercialized batteries for electric storage, electric vehicle, and mobile electric items.

• 한국수소및신에너지학회논문집
• /
• 제26권5호
• /
• pp.393-401
• /
• 2015

The characteristics of diesel and biodiesel are similar like as cetane number and auto-ignition temperature. High cetane number of diesel and BD could make possible to compression ignition. but BD showed different atomization from diesel due to component like density, viscosity and iodine value etc. Because of this, the biodiesel requires validation. This study using diesel and BD20 investigated effect to durability injector. Durability test were used common rail and bosch solenoid type 5-hole injector. Total test was 672hr but actual running time was 200hr. Spray experiments for spray characteristics were carried out using constant volume combustion chamber. Spray characteristics of diesel and BD showed different result up to durability test time. After 100hr, diesel showed spray shapes were stable but BD was not. After 200hr, difference of diesel and BD spray shapes were grow serious.

• 한국수소및신에너지학회논문집
• /
• 제27권1호
• /
• pp.42-48
• /
• 2016

This study presents an experiment investigation on natural convection heat transfer of air-cooling Proton exchange membrane fuel cells (PEMFCs) in a enclosure system for unmanned aerial vehicles (UAVs). Considered are replacing fuel cell stack with Aluminum block for heat generating inside a enclosure chamber. The volume ratio of fuel cell stack and chamber for simulation to the actual size of aerial vehicle is 1 to 15. The parameters considered for experimental study are the environmental temperature range from $25^{\circ}C$ to $-60^{\circ}C$ and the block heat input of 10 W, 20 W and 30 W. Effect of the thermal conductivity of the block and power level on heat transfer in the chamber are investigated. Experimental results illustrate the temperature rise at various locations inside the chamber as dependent upon heat input of fuel cell stack and environmental temperature. From the results, dimensionless correlation in natural convection was proposed with Nusselt number and Rayleigh number for designing air-cooling PEMFC powered high altitude long endurance (HALE) UAV.

• 한국수소및신에너지학회논문집
• /
• 제23권5호
• /
• pp.484-492
• /
• 2012

The TMS(Thermal Management System) heater in a fuel cell vehicle has been developed to prevent a decline of fuel cell durability and cold start durability. Main functions of the COD(Cathode Oxygen Depletion) heater are depletion of oxygen in a cathode as heat energy and consumption of electric power for rapid warming up of a fuel cell stack. This paper covers subjects including the design specification of a heater, heater controller for detection of overheat and reliability assessment including coolant pressure cycle test of a heater. To verify the design concept, burst pressure and deformation analysis of plastic housing were carried out. Also, temperature distribution analysis of heater surface and coolant inside of housing were carried out to verify the design concept. By designing the plastic housing instead of a steel housing, the 30% weight lightening and 50% cost reduction were attained. A module-based design of a TMS system including a heater or reducing the watt density of a heater is a problem to be solved in the near future work.

• 한국수소및신에너지학회논문집
• /
• 제21권2호
• /
• pp.111-116
• /
• 2010

In this study, the structural analysis was performed to optimize the membrane humidifier with hollow fiber membrane for polymer electrolyte membrane fuel cell system. The main design factors were considered by evaluating the humidifying performance according to various structural parameters such as packing density and length. The effects of operation conditions of membrane humidifier were also elucidated experimentally. Results imply that there are optimum points for the packing density and length of humidifier. It was also found that among operation conditions, relative humidity of wet exhaust gas and temperature of dry inlet gas have major effects on the humidifying performance.

• 한국수소및신에너지학회논문집
• /
• 제21권2호
• /
• pp.129-135
• /
• 2010

Homogeneous charge compression ignition (HCCI) engines have the potential to provide both diesel-like efficiency and very low emissions of nitrogen oxide (NOx) and particulate matter(PM). However, several technical issues still must be resolved before HCCI can see application. Among these, steep pressure-rise rate which leads to narrow operating range of HCCI engine continues to be a major issue. This work investigates the combination of two methods to mitigate the excessive pressure-rise rates at high power output, namely fuel stratification and Cooled exhaust-gas recirculation (Cooled EGR), after identifying the each effects to pressure-rise rate. When applying the fuel stratification to simulation, total fuelling width of 0.15 at BDC is set as a equivalent ratio difference based on the previous research. In order to simulate the effects of cooled EGR, $CO_2$ mole fraction in pre-mixture is changed ranging from 0 to 30%. DME which has a characteristic of two-stage ignition is used as a fuel.

• 전력전자학회논문지
• /
• 제25권1호
• /
• pp.37-43
• /
• 2020

This study proposes a 7kW low-voltage DC-DC converter (LDC) using a coupled inductor (CI) for heavy hydrogen electric transport vehicles. The LDC uses a phase-shift manner for soft switching. SiC-MOSFET is used to reduce the loss of reverse recovery current through the use of a high switching frequency. LDC is require large transformer and inductor because of large output current. The size of transformer and inductor can be reduced by deviding the transformer and inductor into two pieces each. This work presents the experimental results of the proposed circuit.

• Korean Chemical Engineering Research
• /
• 제56권6호
• /
• pp.909-913
• /
• 2018

A hydrocarbon trap (HT) plays an important role of controlling vehicle emissions in the so-called cold emission period by holding hydrocarbons until three way catalysts (TWCs) are thermally activated. In this study, we have investigated the adsorption characteristics of cation (H, La, K, and Ag)-exchanged ZSM-5 zeolites for hydrocarbons (propylene, n-butane, and toluene) by DFT (density functional theory)-based computational chemistry. Cation exchange is to improve the hydrothermal stability of zeolites and their adsorption capacity, thereby rendering cation-exchanged zeolites promising materials for HT. The idea of cluster approximation makes the calculation of adsorption energies superbly efficient in computation. The results showed that Ag-exchanged ZSM-5 would be the best for the adsorption of all three adsorbates, without often encountered Ag oxidation in experiments. Besides, the hydrothermal stability of La-exchanged ZSM-5 was confirmed from the change of geometrical parameters by cation exchange, and it showed good adsorption capacity for propylene and toluene. Hydrogen-exchanged ZSM-5 was also good for hydrogen adsorption, but had poor hydrothermal stability.

• 소성∙가공
• /
• 제28권4호
• /
• pp.203-211
• /
• 2019

In this study, the weight of type IV pressure vessel is optimized through the burst pressure condition using the finite element analysis (FEA) based on the genetic algorithm (GA). The optimization design variables include the thickness of composite layers and the winding angles. The optimized design variables are validated using the numerical simulations for the pressure vessel. Consequently, the weight is decreased by about 6.5% as compared to the previously reported results for Type III pressure vessel. Additionally, a method which reduces the entire optimization time is proposed. In the original method, the population size is constant across all generations. However, the proposed method could reduce the workload through the reduction of the population size by half for every 25 generations. Thus, the proposed method is observed to increase the weight by about 0.1%, however, the working time for the optimization could be decreased by about 46.5%.

• 디지털융복합연구
• /
• 제19권5호
• /
• pp.279-284
• /
• 2021

본 연구에서는 3차원 전산유체역학 (3-D computational fluid dynamics, CFD)을 이용하여 고체고분자전해질형연료전지 (proton exchange membrane fuel cell, PEMFC)의 기체유로에 대한 성능에 관한 전산모사를 실시하였다. 또한 이 전산모사를 통하여 유체의 농도와 압력분포, 그리고 전류밀도의 분포 등 각종 분포에 관하여 연구를 진행하였다. 본 논문에서는 단일유로와 5개의 유로를 비교분석 하였다. 그 결과 5개의 유로가 단일유로에 비하여 각종 분포들이 균일하였고, 성능 또한 월등하였다. 특히 단일유로에서는 물질전달에의한 성능저하 영역에서 매우 낮은 성능을 확인할 수 있었고 반면 5개의 유로에서는 이 부분을 극복하여 보다 높은 성능을 확인할 수 있었다.