• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.71-74
• /
• 2005

In manufacturing automotive parts, such as engine cradles, frame rails, subframes, cross-members, and other parts from circular tubes, pre-bending and pre-forming operations are often required prior to the subsequent tubular hydroforming process. During some pre-forming operations, the cross section of a bent circular tube is crushed into an oval-like shape to ensure proper geometry and sufficient clearance in the hydroforming dies. For such applications, the use of oval Instead of circular tubes could be an effective means of eliminating the pre-forming step. The oval tube could also be produced with less thinning and with less strain on the outside of the bend when controlled by a booster system without the use of mandrel. Hence, the understanding of the issues that occur in the bending of oval tubes is worthy of Investigation. This paper presents parametric studies on the bending of oval tubes without a mandrel. The finite element modeling technique is used to examine the deformation characteristics for both circular and oval tubes. In the simulations, the bending process parameters of bend radius, aspect ratio of the tube ovalness, and tube wall thickness are varied. Observations are made to obtain a hoop-buckle limit diagram in terms of a non-dimensional shape degradation factor. Suggestions based upon developed criteria are made on the acceptability of bend tubes suitable for hydroforming applications without the need ofa pre-forming step or the used of a mandrel.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.306-309
• /
• 2007

In this study, hydroforming characteristic of the double-layered tube was investigated in the hydroforming process. The double-layered tube can be made outer surface on the stainless steel by only one processing. The free bulging test was performed to analysis optimized pressure and axial feeding amount of the double layered tubes. And the experimental results between stainless/carbon and carbon/carbon double-layered tube were compared with the forming data. Moreover analysis model that can be hydroformability and predictable forming pressure of double-layered tube was presented.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.364-367
• /
• 2001

Recently social demands of fuel economy and environmental regulation require the development of light materials and new manufacturing technologies. In this point, aluminum tube hydroforming, which is satisfied with good strength-to-weight ratio and recyclability, is new innovative concept. but, up to now the level of that is relatively low. In this paper, we studied formability of different aluminum tubes in different heat treatments under internal pressure and axial feeding, and mechanical properties of aluminum tubes before and after hydroforming.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.241-244
• /
• 2003

The productivity of hydroforming process can be increased by combining pre-forming process and post-forming process such as the bending, piercing and the embedding process. Therefore in this study, integrated studies on the hydro-embedding technology have been performed by analyzing the deformed mode of the tubes and the optimal process parameters. In the case of the embedding test the characteristics of the embedded parts, such as the shape of the screw tip, screw thread and shape of thread were investigated at various process conditions. To measure the clamping force between the embedded part and the tube, special measuring device was used.

• 소성∙가공
• /
• 제11권3호
• /
• pp.246-254
• /
• 2002

A simple method to derive an optimal pressure curve, characterized by initial pressure, final pressure and pressure path, has been proposed. The initial pressure has been determined from the condition to prevent recoiling phenomenon in the early stage, while the final pressure is from the FE analysis and pressure path is from the punch penetration volume. In order to realize the pressure curve, an open loop control system based on a proportional relief valve has been developed for the renovated CNC hydroforming press. Through the comparison of experiment and analysis, the predicted pressure curve has been verified optimal curve since no defect has been observed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.642-647
• /
• 2007

Determination of loading conditions for tube hydroforming(THF) process that implies an amount of the increment in axial feeding and internal pressure for each step is one of the most important constituents at the process design level. On account of the fact that those design factors mentioned above are imposed simultaneously during the process, suitable loading conditions are required to obtain robust products without any failure such as buckling, necking, bursting and so on. In which, especially, bursting is well known as the most frequently occurred failure in general THF process. In this study, therefore, determination of the loading condition based on the adaptive method was carried out to obtain safe loading paths. In addition, forming limit curves are applied to evaluate the derived loading conditions by using the simulation results. Consequently, it is found that described method in this study for THF process design is useful and has a feasibility.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 춘계학술대회 논문집
• /
• pp.59-62
• /
• 2001

Welded blank hydroforming technology is applied to an automotive subframe which has been manufactured by stamping and welding processes. Blank shape and die system is suggested on the basis of finite element analyses. Various defects, especially wrinkling problems in the area of sudden section change, are investigated, analyzed and tried out. The blank shape and the die system are modified to get the sound welded blank hydroformed subframe.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 춘계학술대회 논문집
• /
• pp.202-205
• /
• 2004

A bumper comprises a bumper face, a bumper beam for distributing the load from the impacts applied to the bumper face and reinforcing the bumper, an absorber member interposed between the bumper face and the bumper beam, and a pair of bumper stays which secure the bumper beam to the vehicle body. A conventional bumper stay structure is assembled into several stamped parts, so several processes are needed and the structure is complicated. In this study the bumper stay is applied to the tubular hydroforming which is known to have several advantages such as the reduction of the number of the process and the part weight. The thickness distribution of the tube is mainly considered to evaluate the hydro-formability and the shape of the tube is determined.

• 소성∙가공
• /
• 제16권6호
• /
• pp.426-431
• /
• 2007

Hydroformability and fracture criteria of FE analysis based on ductile fracture were investigated in warm hydroforming of A16061 tube. To evaluate the hydroformability, uni-axial tensile test and bulge test were performed at room temperature and $200^{\circ}C$. The measured flow stresses were used as input parameters for FE analysis. The damage values were calculated by FE analysis based on ductile fracture criteria at maximum radius of free bulged tubes. Damage values were compared of hexagonal shaped hydroformed parts. As a result, the formability by critical damage value for extruded tube is lower than that of full annealed tube up to 0.5.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.35-38
• /
• 1999

Tube bending is an important factor of the hydroforming processes. The tube must be bent to the approximate centerline of the finished part prior to hydroforming to enable the tube to be placed in the die cavity. This paper presents the simulation results in prebending process by a rotary bending machne and a bend die that is used to form an automotive part a tie bar, Prebending simulation is carried out to obtain the shape change of cross section and thinning in bending process. To avoid occurring wrinkle in compressive zone during bending process a wiper die included,. A parametric study is carried out to obtain the effect of the forming parameters such as a bend radius and tube thickness