• Tribology and Lubricants
• /
• 제28권2호
• /
• pp.81-92
• /
• 2012

To product multi-grade oil like engine oil, a sort of mineral base oil is mixed with a fundamental additive liquid package and a polymer liquid as viscosity index improver in order to improve the lubricating property of oil. That is, engine oil is the mixture of more than two fluids. In this paper, it will be systematically organized the governing equation describing non-Newtonian thermo-hydrodynamic lubrication related with the mixture of incompressible fluids based on the principle of continuum mechanics. Then, in order to find how the thermal analysis effect on the bearing performance lubricated with the mixture of multi-fluids, it will be compared to the performances between the mixture of each liquid to be blended and multi-grade engine oil as a single fluid in a high speed journal bearing. It is found that, in the case of lower viscosity oil, the difference of pressure distribution between the above two cases turns out to be existed, even if the load capacity is same level.

• 해양환경안전학회지
• /
• 제18권6호
• /
• pp.577-583
• /
• 2012

부유구조물은 해양에서 다양한 외력을 경험하게 되며 특히, 파랑하중은 구조물의 설계에 결정적인 지배인자로 간주되고 있다. 이런 구조물은 파장과 크기의 상대적 관계로 소형구조물, 대형구조물 등으로 구분될 수 있으며 전통적으로 소형구조물은 회절발생이 없는 것으로 가정하며 대형구조물은 회절 작용에 따른 관성력만을 고려하여 파랑하중을 산출한다. 따라서 이 연구에서는 해양과 강, 호수 등에서 주로 사용되고 있는 정사각형 부유구조물을 이용하여 동유체력과 구조응답의 상관관계를 파악하여 장방형 부유구조물의 안전성에 대한 영향을 검토하였다.

• 한국환경과학회지
• /
• 제12권9호
• /
• pp.957-966
• /
• 2003

Gunsan coastal area is one of region increasing pollution problems. To improve water quality, the reduction of these nutrients loads should be indispensible. In this study, the three-dimensional numerical hydrodynamic and ecosystem model were applied to analyze the processes affecting the eutrophication. In field survey, the average concentrations of dissolved inorganic nitrogen (DIN) and dissolved inorganic phosphorus(DIP) at surface waters were found to be 0.43mg/$\ell$ and 0.03mg/$\ell$ respectively, which were exceeding second grade of water quality criteria. In hydrodynamic modelling, the comparison between the simulated and observed tidal ellipses showed fairly good agreement. The ecosystem model was calibrated with the observed data in study area. The simulated results of DIN were fairly good coincided with the observed values within relative error of 32.39%, correlation coefficient(r) of 0.99. In the case of DIP, the simulated results were fairly good coincided with the observed values within relative error of 24.26%, correlation coefficient(r) of 0.82. The simulations of DIN and DIP concentrations using ecosystem model were performed under the conditions of 20∼80% reductions for pollutant loading. At simulation results, concentration of DIN and DIP were reduced to 20∼80% and under 10% in case of the 80% reduction of pollutant loading, respectively.

• Tribology and Lubricants
• /
• 제14권4호
• /
• pp.100-107
• /
• 1998

A new bearing concept, the wave journal bearing, has been developed to improve the static and dynamic performance of a hydrodynamic journal bearing. This concept features a wave in bearing surface. Not only straight but also twisted wave journal bearing are investigated numerically. The performances of straight and twisted bearings are compared to a plain journal bearing over a wide range of eccentricity. The bearing load and stability characteristics are dependent on the geometric parameters such as the number of waves, the amplitude and the start point of the wave relative to the applied load direction. The wave journal bearing, especially for the twisted one, offers better stability than the plain journal bearing under all eccentricity and load orientation.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제27회 춘계학술대회
• /
• pp.190-197
• /
• 1998

A new bearing concept, the wave journal bearing, has been developed to improve the steady and dynamic performance of a hydrodynamic journal bearing. This concept features a wave in inner bearing surface. Not only straight but also twisted wave journal bearing are investigated numerically. The performances of straight and twisted bearings are compared to a plain journal bearing over a relatively wide range of eccentricity. The bearing load and stability characteristics are dependent on the geometric parameters such as the number of waves, the amplitude and the starting point of the wave relative to the applied load. The wave journal bearing, especially for the twisted one, offers better stability than the plain journal bearing under all eccentricity and all wave to load orientation.

• 대한조선학회지
• /
• 제15권3호
• /
• pp.1-7
• /
• 1978

The dynamic pressures on the bottom of high speed small crafts are studied. Using the dynamic load factor the dynamic pressure can be replaced by equivalent static pressure. Assuming that (1) the system is undamped with a single degree of freedom and (2) the load is applied triangularly, we obtained the max, value of the dynamic load factor of 1.455. We believe that this method could provide a guide to the designer who has no data on the craft in the preliminary structural design stage.

• KSTLE International Journal
• /
• 제2권2호
• /
• pp.146-149
• /
• 2001

Recently, laser printers have been developed to have high-speed laser scanner with hydrodynamic bearings. Among the bearings, herringbone grooved bearing (HGB) produces hydrodynamic pressure by high-speed rotating and so make the surfaces between the shaft and sleeve separated. Accordingly, the bearings with non-contact rotation are suitable to high-speed rotating and have long bearing life and reliability. HGB is a kind of journal bearing and uses oil for a lubricant. HGB has excellent stiffness and load carrying capacity. Also, HGB is leakage-free due to groove pumping action. Consequently, HGB is valuable to be applied to high-performance devices such as hard disk drive, copier, and so on.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.87-88
• /
• 2002

To analyze complicated phenomena on the fluid hydrodynamic and the elastic deformation between sliding body surfaces, an analysis to the elastohydrodynamic lubrication of sliding contacts has been developed taking into account the thermal and non-Newtonian effects. The computational technique handled the simultaneous solution of the non-Newtonian hydrodynamic effects, elasticity, the load, the viscosity variation, and temperatures rise. The results included the lubricant pressure profile, film thickness, velocity, shear stress, and temperature distribution, and the sliding frictional force on the surface at various slip conditions. These factors showed a great influence on the behavior resulted in the film shape and pressure distribution. Especially, Non-Newtonian effects and temperature rise by the sliding friction force acted as important roles in the lubrication performance.

• 한국기계가공학회지
• /
• 제3권2호
• /
• pp.86-94
• /
• 2004

The flash temperature distribution on the contact surfaces between cam and roller-follower mechanism was analysed numerically. The elasto-hydrodynamic lubrication pressure and film thickness were used to get the accurate analysis results. The temperature distribution was obtained by numerical integration by making use of Carslaw and Jaeger's formulation to the whole contact surfaces. The maximum flash temperature was increased with both the increasing slip ratio of the contact surface and increasing external load Profile of the temperature distribution was affected by the sliding velocity of the surface.

• 대한기계학회논문집A
• /
• 제26권3호
• /
• pp.544-552
• /
• 2002

Recommended seismic design guide for the flat bottom vortical-cylindrical oil storage tanks in KS B 6225 is presented. Under earthquake excitations, the hydrodynamic pressure exerted on the tank walls produces overturning moment which may cause either a failure of the anchors or a buckling of the tank shell near its base. The basis for establishing design loads due to hydrodynamic pressure is described including seismic zone risk map in Korea, zone coefficients and the essential facilities factor. This procedure for calculating applied compressive stress on the shell base subjecting to seismic load and for estimating the allowable buckling stress is described.