• Korean Journal of Metals and Materials
• /
• v.48 no.2
• /
• pp.148-153
• /
• 2010

The effects of Cu(II) and Al(III) on the extraction and separation of Pt(IV) and Pd(II) have been investigated in a mixed chloride solution using Alamine336 as the extractant. In the HCl concentration range of 1 to 5 M, more than 99% of Pt and Pd could be extracted by Alamine336 from all of the mixed chloride solutions investigated in this study. Lower HCl concentration led to a higher separation factor between Pd and Pt when Alamine336 concentration was constant. Extraction percentage of Cu increased with the increase of HCl concentration, while that of Al was nearly constant at 33% in our experimental range. The optimum conditions to extract Pt and Pd from Cu or Al and the separation factor under these conditions were obtained.

• Transactions of the Korean hydrogen and new energy society
• /
• v.34 no.6
• /
• pp.785-791
• /
• 2023

Copper sulfide (Cu_xS) has been extensively utilized as a counter electrode (CE) material for quantum dot solar cells (QDSCs) due to its exceptional catalytic activity for polysulfide electrolytes. The typical fabrication method of Cu₂S CEs based on brass substrate is dangerous, involving the use of a highly concentrated hydrochloric acid solution in a relatively high temperature. In contrast, electroplating presents a safer alternative by employing a less acidic solution at a room temperature. In addition, the electroplating method increases the probability of obtaining CEs of consistent quality compared to the brass method. In this study, the optimized electroplating cycle for CuS CEs in QDSCs has been studied for the highly efficient photovoltaic performances. The QDSCs, featuring electroplated CuS CEs, achieved an impressive efficiency of 7.18%, surpassing the conventional method employing brass CEs, which yielded an efficiency of 6.62%.

• Tribology and Lubricants
• /
• v.39 no.6
• /
• pp.244-249
• /
• 2023

This paper presents a comprehensive analysis of the impact of surface roughness on the friction and wear properties of SUS 321, an austenitic stainless steel variant produced using the laser powder bed fusion (LPBF) technique, which is a prevalent additive manufacturing method. After the LPBF fabrication, the specimens go a heat treatment process aimed at alleviating residual stress. Subsequently, they are polished extensively to achieve a refined and smooth surface. To deliberately introduce controlled variations in surface roughness, an etching process is employed. This multi-step method encompassed primary etching in a 3M hydrochloric acid solution, followed by secondary etching in a 35 wt% ferric chloride solution, with varying durations applied to different specimens. A comprehensive evaluation of the surface characteristics ensued, employing precise techniques such as surface roughness measurements and meticulous assessments of water droplet contact angles. Following the surface treatment procedures, a series of friction tests are performed to explore the tribological behavior of the etched specimens. This in-depth investigation reached its peak by revealing valuable insights. It clarified a strong correlation between intentionally altered surface roughness, achieved through etching processes, and the resulting tribological performance of LPBF-fabricated SUS 321 stainless steel. This significantly advances our grasp of material behavior in tribological applications.

• Journal of the Korean Chemical Society
• /
• v.29 no.2
• /
• pp.164-171
• /
• 1985

The salicylic acid-formaldehyde condensed copolymer (SAF) and the 3-carboxy-4-hydroxy benzyl methacrylate divinylbenzene copolymer (CHBM-DVB) were synthesized. The capacities of SAF and CHBM-DVB ion exchangers were 4.6meq/g and 3.9 meq/g, respectively. The adsorption of several heavy metal ions on these weakly acidic ion exchangers and the property of ion exchanger were discussed. The distribution coefficients in hydrochloric acid solution and the elution behavior of several heavy metal ions were also discussed.

• Membrane and Water Treatment
• /
• v.1 no.1
• /
• pp.39-47
• /
• 2010

Using a conventional two-compartment cell with stirrers the separation of an aqueous solution of HCl-$NiCl_2$ by an anion-exchange membrane Neosepta-AFN was investigated. The dialysis process was characterized by the permeability coefficient of the membrane towards to $Cl^-$ ions. This quantity was determined by the numerical integration of equations, which describe the time dependence of the total concentration of $Cl^-$ ions in compartment initially filled with stripping agent (water), combined with an optimizing procedure. The analysis of the experimental results showed that this permeability coefficient is a satisfactory characteristic for the process studied. It can be graphically correlated with the initial acid and initial salt concentrations in the compartment initially filled with acid+salt mixture.

• Journal of Pharmaceutical Investigation
• /
• v.29 no.1
• /
• pp.1-5
• /
• 1999

The bioavailabilities of baicalin in water, oil, w/o and o/w emulsion were evaluated in rats. The dissolution rate of baicalin in o/w emulsion was smaller than those of w/o form in dilute hydrochloric acid solution (pH 1.2) and in PBS (pH 6.8). The absorption rate of baicalin from w/o emulsion was smaller than that of o/w emulsion in the different parts of rat intestine of the rats. Following oral administration in rats, the $C_{max}$ of baicalin from water phase, oil phase, o/w wand w/o emulsion were 2.11, 0.61, 1.57, and $1.35\;{\mu}g/ml$, respectively. The relative bioavailability of w/o emusion was 129 % when it was compared with water phase. This result suggests that the improvement of bioavailability for baicalin in w/o emulsion might be practically available.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.28 no.2
• /
• pp.339-353
• /
• 1998

The purpose of this study was to investigate whether a radiographic estimate of osseous fractal dimension and power spectrum of 2D discrete Fourier transform is useful in the characterization of structural changes in bone. Ten specimens of bone were decalcified in fresh 50 ml solutions of 0.1 N hydrochloric acid solution at cummulative timed periods of 0 and 90 minutes. and radiographed from 0 degree projection angle controlled by intraoral parelleling device. I performed one-dimensional variance. fractal analysis of bony profiles and 2D discrete Fourier transform. The results of this study indicate that variance and fractal dimension of scan line pixel intensities decreased significantly in decalcified groups but Fourier spectral analysis didn't discriminate well between control and decalcified specimens.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.9
• /
• pp.2488-2492
• /
• 2010

A method is described for the determination of the Po nuclides in a water sample. After the Po nuclides were purified from interfering elements in a water sample using a manganese dioxide precipitation followed by a solvent extraction method, the Po nuclides were deposited onto the silver plate. A large volume of the water sample was effectively pretreated with manganese dioxide precipitation method. To determine the optimum conditions for plating Po, the effects of the pH, volume, temperature and time on the Po deposition were investigated in hydrochloric acid solution. The investigated determination method of Po nuclides with solvent extraction was applied to a tap water sample.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2003.11a
• /
• pp.642-647
• /
• 2003

Palladium is widely used for several applications and recovery of palladium from secondary sources becomes increasingly important since palladium is one of maldistributed platinum group metals. Electrochemical recovery of dense palladium metal sheet from Pd leaching solution is a simple and easily controlled method. The surface morphology of the recovered Pd metal was significantly affected by current density and temperature. Dense deposit morphology was in higher stress state regardless of preparation condition under $55^{\circ}C$. Rising temperature up to $70^{\circ}C$ had a stress releasing effect besides densification of Pd deposit.

• Journal of the Korean institute of surface engineering
• /
• v.30 no.1
• /
• pp.44-56
• /
• 1997

Influence of electrochemical etching conditions on capacitance gain of aluminium electrolytic on capacitor foil has been investigated by etching cubic textured high purity aluminum foil in dilute hydrochloric acid. Uniformly distributed etch pit tunnels on aluminum surface have been obtained by pretreatment aluminium foil in 10% NaOH solution for 5 minutes followed by electrochemical etching. Electrostatic capacitance of etched aluminium foil anodized to high voltage increased with the increase of current density, total charge, temperature and concentration of electrolyte up to maximum CV-value and then deceased. Election optical observation of the etched foil revealed that the density of etch of etch pits increased with the increase of current density and concentration of electrolyte. this increase of etch pit density enlarged of the increase of capacitance. However, abnormal high current density and high electrolyte concentration induced the local dissolution of the foil surface which resulted the decrease of foil capacitance.