• 한국산학기술학회논문지
• /
• 제20권12호
• /
• pp.797-803
• /
• 2019

본 연구는 동력분산형 고속열차의 횡방향 진동을 저감하기 위하여 진행되었다. 동역학 해석을 통한 연구에서 동력분산형 고속열차 시제차량(HEMU-430X)은 고속열차에서 주로 사용되는 차륜프로파일(XP55, GV40, S1002)에 관계없이 낮은 등가답면구배에서 횡방향 진동이 커지고, 차륜 마모가 진행되어 등가답면구배가 커지면 횡진동이 감소하는 경향을 보였다. 이는 HEMU-430X에 적용된 현가장치 특성치들의 조합된 결과로 인해 등가답면구배가 낮을 때 차체와 대차가 1.4Hz의 주파수로 공진하여 차체 헌팅이 발생되기 때문이다. 고속열차의 횡방향 진동저감에 대한 해외 사례에서 요댐퍼의 유압강성(Hydraulic stiffness)을 낮추어 진동을 개선한 사례를 고찰하였다. 요댐퍼의 시리즈 강성은 유압강성과 탄성조인트의 조합인데 본 연구에서는 유압강성 조정대신 비교적 간단하게 할 수 있는 탄성조인트의 강성을 낮추어 횡방향 진동을 개선하고자 하였다. 신규 제작된 탄성조인트를 적용한 요댐퍼의 시리즈 강성은 기존 요댐퍼 대비 60% 수준으로 낮았다. 60% 수준의 시리즈 강성이 적용된 요댐퍼를 HEMU-430X의 TC~M2 3량에 설치하여 시운전 시험을 수행하였다. 시운전 시험 결과 TC를 선두로 한 하행 주행 시 TC~M1의 횡방향 진동이 개선되고, MC를 선두로 한 상행 주행 시 후미 TC차량의 횡진동이 개선되는 결과를 보였다. 본 연구의 진동저감 방안은 향후 영업운전을 위해 도입되는 EMU-250 및 EMU-320의 횡방향 진동 문제 발생 시 해결책으로 적용할 수 있다.

• 한국지진공학회논문집
• /
• 제2권3호
• /
• pp.51-60
• /
• 1998

Base isolation is an innovative design strategy that provides a practical alternative for the seismic design of structures. Base isolators, mainly employed to isolate large structures subjected to earthquake ground excitations and to rehabilitate structures damaged by past earthquakes, deflect and absorb the seismic energy horizontally transmitted to the structures. This study demonstrated that the base isolation system may offer effective performance for bridges during severe seismic events through shaking table tests. Two base isolation systems using laminated rubber bearings with and without hydraulic dampers are tested. The test results strongly show that the laminate rubber bearings cause the natural period of the bridge structure increased considerably, which results in the deck acceleration and the shear forces on the deck acceleratino and the shear forces on the piers reduced significantly. The results also demonstrate that the hydraulic dampers enhance the system's capacity in dissipating energy to reduce the relative displacement between the bridge deck and the pier.

• 드라이브 ㆍ 컨트롤
• /
• 제9권4호
• /
• pp.62-69
• /
• 2012

Recently, hydraulic motor is getting the spotlight. It is resulted from rapid civil engineering public works by a lot of developing countries around the world. In this study, we divided the valves which are affixed in the hydraulic motor into some parts, implemented them through computer simulation, verified validation of each component, and analyzed behavior adding driving condition. Through the analyzed results with general driving condition, we found the reason why behavior became unstable as the motor had started spinning. Through the analyzed results with tough driving condition, we verified that the valve works well with it's production purpose.

• 대한기계학회논문집 C: 기술과 교육
• /
• 제3권2호
• /
• pp.131-140
• /
• 2015

하반신 마비환자가 스키를 탈 수 있도록 고안된 모노스키는 스키 플레이트 위에 좌석이 설치된 형태의 썰매이다. 스키를 탈 때 설면으로부터 전달되는 충격은 정상인의 경우 다리관절의 거동에 의하여 흡수되지만 모노스키의 경우에는 좌석에 탑승한 인체에 그대로 전달된다. 상용화된 대부분의 모노스키에는 이를 보완하기 위하여 스키 마운트와 시트 간에 링크 메커니즘과 충격완충장치가 설치되어 있다. 본 연구에서는 유압 실린더가 장착된 모노스키의 주행 시뮬레이션을 수행하고 불규칙한 표면 주행 중 발생하는 진동 충격 가속도를 분석하여 탑승자의 안락감을 평가할 수 있는 모델을 개발하였다. 안락감 평가방법은 국제 규격인 BS6841 을 사용하였다. 개발 모델을 이용하여 유압 완충장치의 노즐조절에 따른 안락감을 평가하였다.

• 대한기계학회논문집A
• /
• 제25권4호
• /
• pp.685-694
• /
• 2001

In this study, a transfemoral prosthesis system of which both stance phase and swing phase are controllable has been developed for the recovery of the biomechanical function of the amputated leg. It consists of a 5 bar link mechanism, a hydraulic-rubber knee damper for stance phase control and a pneumatic cylinder controlled via a microprocessor for stance phase control. The mechanical characteristics of the knee damper which absorbs the impact energy generated at the heel contact were investigated. The characteristics of the pneumatic cylinder essential for the speed adaptation of the prosthesis during swing phase were also studied for its mechanical characteristics. The prosthesis was subject to the clinical tests, and the gait characteristics obtained were very close to those of normal subjects. The stance and swing controlled prosthesis that were developed in this study showed good stability during the stance phase and showed good controllability during the swing phase.

• 한국소음진동공학회논문집
• /
• 제26권1호
• /
• pp.82-88
• /
• 2016

This paper proposes a new type of semi-active direct-drive valve(DDV) car suspension system using piezoelectric actuator associated with displacement amplifier. As a first step, controllable piezoelectric DDV damper is designed and governing equation of a quarter-vehicle suspension system consisting of sprung mass, spring, tire and the piezostack DDV damper is constructed. After deriving the equations of the motion, in order to control spool displacement and damping force the skyhook controller is designed and applied. The performance evaluation of the proposed semi-active suspension system is conducted with different displacement of spool. Then, the ride comfort analysis is undertaken in time domain with bump road profile.

• Smart Structures and Systems
• /
• 제14권6호
• /
• pp.1081-1103
• /
• 2014

Real-time hybrid simulation (RTHS) has emerged as an important tool for testing large and complex structures with a focus on rate-dependent specimen behavior. Due to the real-time constraints, accurate dynamic control of servo-hydraulic actuators is required. These actuators are necessary to realize the desired displacements of the specimen, however they introduce unwanted dynamics into the RTHS loop. Model-based actuator control strategies are based on linearized models of the servo-hydraulic system, where the controller is taken as the model inverse to effectively cancel out the servo-hydraulic dynamics (i.e., model-based feedforward control). An accurate model of a servo-hydraulic system generally contains more poles than zeros, leading to an improper inverse (i.e., more zeros than poles). Rather than introduce additional poles to create a proper inverse controller, the higher order derivatives necessary for implementing the improper inverse can be calculated from available information. The backward-difference method is proposed as an alternative to discretize an improper continuous time model for use as a feedforward controller in RTHS. This method is flexible in that derivatives of any order can be explicitly calculated such that controllers can be developed for models of any order. Using model-based feedforward control with the backward-difference method, accurate actuator control and stable RTHS are demonstrated using a nine-story steel building model implemented with an MR damper.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1998년도 춘계학술대회논문집; 용평리조트 타워콘도, 21-22 May 1998
• /
• pp.608-613
• /
• 1998

Damping characteristics of ER dampers and flow rates inside ER valve with two different valve types were analyzed and compared with test results. Fluid flow inside ER valves was modeled by Bingham plastic model and Hagen-Poiseulli flow, while the equations of motion of total ER damper system were modeled by flow and hydraulic force balance. A general straight valve case was compared with a bended valve case which is newly tested for a possible improvement of ER damping force. As expected, the bended ER valve generates higher damping force and lower flow rates than the conventional straight ER valve due to additional flow restriction at the bended section. Analytical models of ER valve and ER damper generally predict reasonable performance characteristics of tested results. Therefore, developed analysis can be used for designing new ER dampers and simulation of ER semi-active suspension system as well.

• 한국소음진동공학회논문집
• /
• 제20권6호
• /
• pp.528-536
• /
• 2010

System identification for cylindrical oil dampers is carried out based on a series of dynamic experimental tests and theoretical approach for the analysis of the experimental data. Experimental tests are conducted using a specific hydraulic actuator in the wide frequency range from 10 Hz to 90 Hz. From this study, it is confirmed that control force of the damper is composed of inertia, damping and restoring components. In general, both restoring and damping components are significant and comparable. However, the portion of the inertia components becomes more significant than to be negligible in the high frequency range.

• 한국자동차공학회논문집
• /
• 제2권2호
• /
• pp.73-82
• /
• 1994

Low-band type active suspension system is implemented on a passenger car. Level. roll, pitch and bouncing motion of body are controlled by a digital controller. Sky-hook damper is applied to control bouncing motion. This paper describes overall construction of the system, design of hydraulic system, sensor system, controller, and control scheme. Performance of prototype car has been evaluated on a test track and reported in the second paper.