• Journal of the Korea Concrete Institute
• /
• v.26 no.5
• /
• pp.615-625
• /
• 2014

Excessive long-term slab deflection caused by construction load is a critical issue for the design of concrete slabs, as long span flat plates become popular for tall buildings. In the present study, the effect of construction load causing early slab cracking on the long-term deflection was theoretically studied. On the basis of the result, a numerical analysis method was developed to predict the long-term deflection of flat plates. In the proposed method, immediate deflection due to slab cracking and long-term effect of creep and shrinkage were considered. To verify the construction load effect, long-term slab deflections were measured in actual flat plate buildings under construction. The results showed that the immediate deflection due to the construction load increased significantly the long-term deflection. The proposed method was used to predict the deflections of the buildings. The results were compared with the measurement results. The predictions agree well with the long-term deflections of flat plate affected by construction load.

• Journal of Environmental Science International
• /
• v.29 no.6
• /
• pp.683-689
• /
• 2020

According to a NASA Goddard Institute for Space Studies report, temperatures have risen by approximately 1℃ so far, based on temperatures recorded in 1880. The 2003 heatwave in Europe affected approximately 35,000 people across Europe. In this study, a cooling fog, which is used in smart cities, was designed to efficiently reduce the temperature during a heatwave and its pilot test results were interpreted. A model experiment of the cooling fog was conducted using a chamber, in which nano mist spray instruments and spray nozzles were installed. The designed cooling fog chamber model showed a temperature reduction of up to 13.8℃ for artificial pavement and up to 8.0℃ for green surfaces. However, this model was limited by constant wind speed in the experiment. Moreover, if the cooling fog is used when the wind speed is more than 3m/s in the active green zone, the temperature reduction felt by humans is expected to be even greater. As a second study, the effect of cooling fog on temperature reduction was analyzed by installing a pilot test inside the Land Housing Institute (LHI). The data gathered in this research can be useful for the study of heat reduction techniques in urban areas.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.7 no.1
• /
• pp.53-60
• /
• 1996

The 8W hybrid MIC SSPA has been developed in the frequency range from 14.0 GHz to 14.5 GHz for uplink of KOREASAT's earth station. The whole system was designed of two parts with driving amplifier and high power amplifier to simplify the fabrication process. we reduced weight and volum of power amplifier through arranging the bias circuits in the same housing. The realized SSPA has a small signal gain of $26\pm1dB$within 500 MHz bandwidith, and the input and output return losses are over 7dB and 12dB respectively. The output power of 39.0 ~ 39.2dBm is achieved at the 1dB gain compression point of 14 GHz, 14.25 GHz, and 14.5 GHz. That reveals higher power than 8W of design target. The proposed SSPA manufacture techni- ques in this paper can be applied to the implementation of power amplifiers for some radars and SCPC.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.9
• /
• pp.813-819
• /
• 2011

In this paper, a new design method of a tunable oscillator using a suspended-stripline resonator is presented. The negative resistance of an FET mounted on microstrip line(MSL) is combined with a high Q suspended-stripline(SSL) resonator to produce a tunable oscillator with good phase noise. The new MSL-SSL transition facilitates the easy connection between the MSL-based circuits and the SSL module. The proposed oscillator is also frequency-tunable using a tuner located on the top of the SSL housing. The measured phase noise of the implemented oscillator at 3.37 GHz is -108.03 dBc@100 kHz and -135.09 dBc@1 MHz with 50 MHz of frequency tuning.

• Journal of the Korea Furniture Society
• /
• v.23 no.3
• /
• pp.324-331
• /
• 2012

The domestic pine was used to investigate the change of specific gravity, moisture contents, color and anatomical structure by accelerated weathering test (AWT). According to visual inspection, a few knot separation and looseness as well as considerable surface discoloration was found out. However, the crack and split of surface texture have been never occurred till the last step of AWT. On the whole, as the time of accelerated weathering test has increased, the specific gravity has decreased. Finally, after the 9th week of AWT, the specific gravity was 0.38 that reached to 82% compared to the control specimen. In case of moisture content (MC), it showed rising trend in its early stages, however, after 3th week of AWT it have displayed steady state. A deterioration of cell-wall components was not remarkably observed by scanning electron microscope (SEM), however the ray fractures of AWT specimen were observed more than those of control specimen. The full fracture of epithelial cell around resin canal was observed by optical microscope. The fracture of ray of 2th cycle AWT specimen was first, followed by 1th week and control group. A distortion of tracheid for early spring wood and fracture of epithelial cell were generally observed by a similar level, regardless of duration time of AWT. Therefore, it is obvious that increasing duration time of AWT does not affect the deterioration of micro-structure for wood members from this study. Although a considerable change of anatomical properties was not found, there is a need of further research to understand how will the changes of specific gravity and MC on the physical properties of wood member.

• Journal of Korean Society on Water Environment
• /
• v.18 no.4
• /
• pp.379-386
• /
• 2002

In this study, estimation model for iron compound originated from upflow, anaerobic fixed bed reactor, which treats sewage domestic wastewater, was developed. The estimation model was formulated by a mathematical expression which was based on the mass balance. Below the HRT of 60 minute, sulfide concentration combining with iron $FeS_2$ is the highest because the maximum sulfate consumption rate $V_{maxS}$ and half-saturation constant of sulfate $K_{mS}$ exert an important effect on the estimation model as temperature was increased. But increment of $FeS_2$ concentration is weakened above the HRT of 60 minutes and represent the lowest value at the HRT of 108 minutes. It implies that liquid phase distribution ratio of sulfide ${\alpha}r$ becomes lower as temperature was increased. While phosphorus concentration combining with iron $Fe_3(PO_4)_3$ is increased as HRT and temperature are increased, which is affected by phosphorus removal rate constant $k_p$. As the result of estimating the iron concentrations of corrosion by the model, the concentration of iron corrosion is higher than any other at the HRT of 108 minute and $20^{\circ}C$. The predicted values were compared with measured ones at different HRT(13.5, 27, 54, 108 min) and temperature(20, 25, $30^{\circ}C$). The experimental data could be fitted with the simulated curves. Therefore, the mathematical expression could be applicable to design full-scale wastewater treatment plants.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.6
• /
• pp.792-797
• /
• 2015

In this study, three softwood species were treated with water-soluble melamine resin by different concentration and treatment time under vacuum pressure for improving mechanical property, abrasion resistance, and incombustibility. After the treatment, a compreg was manufactured and then evaluated on physical properties. Additionally, incombustibility of compreg was determined by comparing with a wood that was treated by spraying a water-soluble fire retardant on surface. As concentration of resin increased, bending strength and Brinell hardness increased as well as abrasion resistance, but there was no correlation on treatment and mechanical properties by treatment time. The wood impregnated by water-soluble melamine resin under vacuum pressure showed better incombustibility than that of a water-soluble fire retardant sprayed wood. Therefore, this treatment could be used for improving incombustibility of wood.

• Journal of the Korea Concrete Institute
• /
• v.27 no.6
• /
• pp.625-632
• /
• 2015

In this study, a comparative analysis have been conducted to examine seismic reinforcement effect of a school building that is designed with a CBD (Channel Beam Damper) system supported by H-frame with existing non-seismic RC frame. As a result of experiment, seismic reinforcement specimen with CBD system showed hysteretic characteristics of a large ellipse with great energy dissipation ability and increased strength and stiffness, while non-seismic design specimen showed rapid reduction in strength and brittle shear failure at top and bottom of the left and right column. In addition, comparing the stiffness reduction between the two specimens, CBD system was effective in preventing the reduction of stiffness. Energy dissipation ability of specimen reinforced by CBD system was about 4.0 times higher than the non-reinforced specimen. Such enhancement in energy dissipation ability could be considered as the result of improved strength and deformation for further application in designing of seismic reinforcement.

• Journal of Korean Home Economics Education Association
• /
• v.28 no.2
• /
• pp.1-19
• /
• 2016

The purpose of this study was to design curriculum content structure integrating three systems of actions for 2009 revised current home economics curriculum. For the development of content structure and content elements, a development team of two home economics scholars, a cooperating team of three home economics teachers, and an expert team of 15 home economics teachers and professors were organized. Phase 1 of curriculum development was developed by integrating three systems of actions with traditional home economics content areas of clothing, food, housing, consumption, and family by the development team. It is examined by the cooperating team and in phase 2 is recommended to build matrix of units of the current curriculum and the three systems of actions. The final phase of curriculum development illustrated a content structure integrating the sub-units of 2009 revised current curriculum and the three systems of action following the expert group's professional opinion.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.67 no.2
• /
• pp.63-69
• /
• 2018

In this paper, the operation principle of a bi-directional switch type resonant AC link snubber circuit was described, together with the practical design procedure, which employs in the proposed power module bridge package type resonant AC link snubber. The novel prototype of power module bridge package type resonant AC link snubber-assisted voltage type sinewave soft switching PWM inverter using IGBT power module was demonstrated herein. It was verified that both the auxiliary power switches in this resonant AC link snubber circuit and the main power switches commutate under the condition of soft switching commutation principle. In addition, the power losses of the new soft switching inverter treated here were analyzed by implementing the experimental data of the IGBT and diode v-i characteristics in addition to switching power loss characteristics into our original computer simulation software developed by the authors. Then, the voltage type sinewave soft switching PWM inverter was high efficiency than that of hard switching PWM inverter, along with performance operation waveforms. In the future, the comparative feasibility study of power module bridge type resonant AC link snubber and its related soft switching inverter in addition to the other types resonant snubber assisted soft switching inverter should be done from a practical point of view.