• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.632-635
• /
• 2001

Microcrystalline Si films have been deposited by using five W-wire filaments of 0.5 mm diameter for hot-wire chemical vapor deposition (HWCVD). We compared the HWCVD grown films with the film exposed to transformer couple plasma system for the modification of seed layer. W-wire filament temperature was maintained below 1600$^{\circ}C$ to avoid metal contamination by thermal evaporation at the filament. Deposition conditions were varied with H$_2$dilution ratio, with and without plasma treatment. From the Raman spectra analysis, we observed that the film crystallization was strongly influenced by the H$_2$dilution ratio and weakly depended on the distance between the wire and a substrate. We were able to achieve the crystalline volume fraction of about 70% with an SiH$_4$/H$_2$ratio of 1.3%, a wire temperature of 1514$^{\circ}C$, a substrate separation distance of 4cm, and a chamber pressure of 38 mTorr. We investigated the influence of ${\mu}$c-Si film properties by using a plasma treatment. This article also deals with the influence of the H$_2$dilution ratio in crystallization modification.

• 오토저널
• /
• 제7권3호
• /
• pp.94-101
• /
• 1985

The flame temperature of LPG-air premixture flame was measured by extrapolation of limiting case corresponding to the infinitely thin diameter of Platinum-resistance-hot-wire. LPG-air premixture flame, initially under atmospheric pressure and room temperature, propagates downward from top of the model combustion chamber maintained at constant pressure through the whole combustion process. Analytical calculation technique was also applied to determine full temperature history or spatial temperature distribution from flame reaction zone to burnt gas region.

• 대한기계학회논문집
• /
• 제5권4호
• /
• pp.320-328
• /
• 1981

Experimental study of a round. free air jet is accomplished using a crossed hot wire probe with a constant temperature hot wire anemometer. Mean velocity Profiles, Reynolds stresses, tubulent intensities, velocity probability densities and correlation functions are measured in the down tream region. These values are calculated and averaged inthe correlation and probability analyzer. The reults are interpreted by the output of te dual beam oscilloscope.

• 대한기계학회논문집
• /
• 제2권2호
• /
• pp.42-46
• /
• 1978

Thermal conductivities of Freon-12 and Freon-22 were measured at room temperature up to 35 MPa with the aid of transient hot wire method. Glycerin was used to check the performance of the experimental equipment. The thermal conductivities of Freon-12 and Freon-22 at the maximum pressure, 35 MPa, were increased by 25% approximately for those at satufated state.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2003년도 추계학술대회 논문집
• /
• pp.31-34
• /
• 2003

The near wake behind a sinusoidal cylinder has been investigated quantitatively using hot-wire anemometer and qualitative. The mean velocity and turbulence intensity were measured in streamwise and spanwise direction. The results show that the wake in the saddle plane has a longer vortex formation region and rapid reversed flow than that in nodal plane. The elongated vortex formation region of sinusoidal cylinder is related with drag reduction. In addition, the flow visualized with particle tracing method support the flow characteristics of sinusoidal cylinder measured by hot-wire.

• Journal of Welding and Joining
• /
• 제33권6호
• /
• pp.36-41
• /
• 2015

In the automotive industry, TWB hot stamping process is broadly adapted to reduce weight of the car and improve fuel efficiency. However, the process faces a problem of weakened strength of the welded zone after hot stamping process, due to the fact that Al-Si elements of the coating layer penetrating the welded zone. In this study, filler wires with high percentages of carbon and manganese is adapted during laser welding process to secure the strength of the fusion zone. In addition, wire feeding speed and laser welding speed are optimized by sample test.

• 한국콘텐츠학회논문지
• /
• 제16권1호
• /
• pp.52-59
• /
• 2016

동절기에 타설되는 대부분의 콘크리트 구조물에서 가설 초기단계에서의 양생방법의 선정은 매우 중요한 요소이다. 동절기에는 초기균열과 강도저하를 방지하기 위하여 열선과 조강시멘트를 이용한 발열양생방법을 주로 적용하게 된다. 하지만 그 적용기법의 단순화 및 경험적 판단에의 의존으로 인하여 대부분의 건설현장에서 최적의 양생방법을 선정하지 못하고 있는 실정이다. 이에 따라 본 논문에서는 비정상상태의 열전달 해법을 통하여 가장 적절한 열선의 가열온도, 기간, 열선 배치간격을 선정하는 평가 알고리즘을 개발하였다. 이를 위하여 관리 매개변수에 주안점을 둔 구조해석 시스템을 통한 사용자 중심의 OOP 루틴을 적용하였다. 본 시스템에서는 입력모듈, DB 모듈, DB저장 모듈, 해석모듈 및 결과분석모듈로 구분하였으며, 각 모듈간의 연계는 visual c# 루틴으로 처리하였다. 또한 그래픽 인터페이스와 DB 테이블은 사용자 편의성을 고려하여 개발하였다.

• 대한기계학회논문집B
• /
• 제27권9호
• /
• pp.1299-1308
• /
• 2003

This paper is studied to investigate the effect of slits and swirl vanes on the development of turbulent flow fields in gun-type gas burner with a cone type baffle plate because this gas burner is generally composed of eight slits and swirl vanes. All of turbulent characteristics including mean velocities were measured in the horizontal plane and cross section by using X-type hot-wire probe from hot-wire anemometer system. This experiment is carried out at flow rate 450 l/min in the test section of subsonic wind tunnel. Slits cause the fast jets, and then they have the characteristic that the flow is not adequately spread to radial direction and has long flow length and very small flow velocity distribution in the central part. On the contrary, swirl vanes does not have long enough for adequate flow length to downstream because the rotational flow diffuses remarkably to radial direction. However, the suitable arrangement between slits and swirl vanes causes effective flow width and flow length, and then it promotes fast flow mixing over the entire region including central part to increase turbulence more largely and effectively. Therefore, it is thought as a very desirable design method in gun-type gas burner to locate slits on the outside of swirl vanes.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.790-798
• /
• 2008

Counter-rotating axial flow fan(CRF) consists of two counter-rotating rotors without stator blades. CRF shows the complex flow characteristics of the three-dimensional, viscous, and unsteady flow fields. For the understanding of the entire core flow in CRF, it is necessary to investigate the three-dimensional unsteady flow field between the rotors. This information is also essential to improve the aerodynamic characteristics and to reduce the aerodynamic noise level and vibration characteristics of the CRF. In this paper, experimental study on the three-dimensional unsteady flow of the CRF is performed at the design point(operating point). Flow fields in the CRF are measured at the cross-sectional planes of the upstream and downstream of each rotor using the $45^{\circ}$ inclined hot-wire. The phase-locked averaged hot-wire technique utilizes the inclined hot-wire, which rotates successively with 120 degree increments about its own axis. Three-dimensional unsteady flow characteristics such as tip vortex, secondary flow and tip leakage flow in the CRF are shown in the form of the axial, radial and tangential velocity vector plot and velocity contour. The phase-locked averaged velocity profiles of the CRF are analyzed by means of the stationary unsteady measurement technique. At the mean radius of the front rotor inlet and the outlet, the phase-locked averaged velocity profiles show more the periodical flow characteristics than those of the hub region. At the tip region of the CRF, the axial velocity is decreased due to the boundary layer effect of the fan casing and the tip vortex flow. The radial and the tangential velocity profiles show the most unstable and unsteady flow characteristics compared with other position of rotors. But, the phase-locked averaged velocity profiles of the downstream of the rear rotor show the aperiodic flow pattern due to the mixture of the front rotor wake period and the rear rotor rotational period.

• 기계저널
• /
• 제33권9호
• /
• pp.780-792
• /
• 1993

난류 열유속 측정을 위한 실험기법을 고찰해본 결과, 열선-냉선 조합 프로브의 사용이 현재로 서는 가장 가능성 있는 기법임을 알 수 있었다. 이와 같은 기법에서 가장 중요한 요소는 난류의 온도 변동량을 정확히 측정할 수 있는 계측장치의 확보임을 알았다. 그동안 사용되어 왔던 각종 냉선온도계의 검토와 본 연구실에서 새로이 개발한 냉선온도계의 설계 및 제작 기법에 대해 소 개하였다. 여러 가지 관점에서의 성능 비교를 통해 본 연구실에서 개발된 냉선 브리지의 성능이 상당히 우수함을 보였다. 난류 열유속의 측정과 비등온 유동에서의 난류 속도 성분을 측정하기 위한 프로브는 X형 hot-wire 프로브와 I형 cold wire 프로브를 조합하여 만들어졌으며, 온도와 속도를 함께 고려하여 교정함으로써 온도구배가 있는 속도장과 난류열유속을 측정할 수 있는 방법을 소개하였다.