• Journal of Mechanical Science and Technology
• /
• 제18권3호
• /
• pp.388-394
• /
• 2004

Composites of Si$_3$N$_4$-SiC containing up to 30 wt% of dispersed SiC particles were fabricated via hot-pressing with an oxynitride glass. To determine the effect of sintering time and SiC content on the mechanical properties and the cutting performance, the composites with fixed 8hr-sintering time and 20 wt% SiC content were fabricated and tested. Fracture toughness of the composites increased with increasing sintering time, while the hardness increased as the SiC content increased up to 20 wt%. The hardness of the composites was relatively independent of the grain size and the sintered density. For machining heat-treated AISI4140, the insert with 20 wt% SiC sintered for 8hr showed the longest tool life while the insert with 20 wt% SiC sintered for 12hr showed the longest tool life for machining gray cast iron. An effort was made to relate the mechanical properties, such as hardness, fracture toughness and wear resistance coefficient with the tool life. However, no apparent relationship was found between them. It may be stated that tool life is affected by not only the mechanical properties but also other properties such as surface roughness, density, grian size and the number of the inherent defects in the inserts.

• 대한기계학회논문집A
• /
• 제25권12호
• /
• pp.1944-1949
• /
• 2001

Four SiC-Si$_3$N$_4$ceramic cutting tools with different composition have been fabricated by hot-pressing. Correlations among the annealing time, the corresponding microstructure and the mechanical properties of resulting ceramics have been investigated. The fracture toughness and the grain size of both SiC and Si$_3$N$_4$in SiC-Si$_3$N$_4$composites increased with the annealing time. 1\`he hardness of SiC-Si$_3$N$_4$composites was relatively independent of the grain size and the sintered density. These ceramic cutting tools were tested under various cutting conditions and compared with the commercial Si$_3$N$_4$ceramic cutting tools. The experimental results were compared in terms of tool life and cutting force. The performance of SiC-Si$_3$N$_4$ceramic cutting tool shows the possibility to be a new ceramic tool.

• 한국의류학회지
• /
• 제37권7호
• /
• pp.952-961
• /
• 2013

This study optimizes a suitable dyeing method for polylactic acid (PLA) fabrics using disperse dyes. For this, disperse red 60 (DR 60), disperse blue 56 (DB 56), and disperse yellow 54 (DY 54) were used and dyed on PLA fabrics dependent of dyeing temperature and time. The fastness of PLA fabrics dyed with three disperse dyes were evaluated; in addition, dye exhaustion, color strength (K/S value), and colorimetric properties of PLA fabrics were compared with PET fabrics. The experiments indicated optimum dyeability of PLA fabrics with disperse dyes. The dyeing temperature was $90^{\circ}C$ for every dye and the dyeing time were 20 min, 60 min, and 40 min for DR 60, DB 56, DY 54, respectively. PLA fabrics had good color fastness to washing, dry cleaning fastness, hot pressing fastness, rub fastness, and perspiration fastness by DR 60, DB 56, and DY 54. The dye exhaustion of PLA fabrics were lower than PET fabrics; however, K/S values were higher than PET fabrics.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.48-48
• /
• 2008

현재 압전재료로써 사용되고 있는 PZT계 세라믹스는 우수한 압전 및 유전특성으로 초음파 센서, 압전변압기, 액츄에이터, 필터, 레조네이터와 같은 여러 응용분야에 널리 사용되어지고 있다. 그러나 납을 60%이상 포함하므로 환경오염에 의하여 그 사용에 대한 규제가 강화되고 있어 최근에는 납을 함유하지 않은 무연 환경친화형 압전세라믹스가 주목받고 있다. 현재 무연 조성 세라믹스에는 텅스텐-브론즈 형, 비스머스 레이어형, 페로브스카이트 형 등이 이으며, 그 중 페로보스카이트 혈을 제외하고는 보통 소성법 조제시 낮은 압전특성을 갖는다. 그러므로 압전특성을 증가시키기 위하여 Hot pressing, Hot forging, RTGG(Reactive Template Grain Growth), SPS(Spark Plasma Sintering), 그러나 이는 무연 세라믹스의 대량생산 과정에서 어려운 문제를 가지고 있고, 저가격 관점에서 볼 때 보통소성법이 보다 바람직하다. 그래서 보통소성법으로 NKN세라믹스의 소결성을 향상 시키고 비교적 높은 압전특성을 얻기 위해서 $LiSbO_3$, $LiNbO_3$, $LiTaO_3$, alkaline-earth(Mg, Ca, Sr, Ba) 등을 첨가한 논문들이 보고되고 있으며, 이러한 재료들의 kp는 대략 0.3-0.4를 나타내고 있다. 따라서, 본 연구에서는 소결온도를 낮추고자 $Ag_2O$를 소결조제로 사용하였고 유전 및 압전특성을 높이고자 소결시간 변화시켜 시편을 제작하여 NKN 세라믹스의 유전 및 압전특성을 조사하였다.

• 한국재료학회지
• /
• 제8권10호
• /
• pp.918-924
• /
• 1998

본 연구는 티타늄과 활성탄소 원료분말을 반응밀링법에 의해 합성시, 밀링시간에 따른 Ti-TiC 복합재료의 미세조직과 기계적 성질에 미치는 TiC vol.% 및 열간압축성형온도의 영향에 관해 조사하였다. 티타늄과 활성 탄소 원료분말을 300시간 밀링 후 $5\mu\textrm{m}$이하의 미세한 구형의 Ti-TiC복합분말을 생성시킬 수 있었다. 반응밀링된 분말을 $1000^{\circ}C$이상에서 1시간동안 진공열간압축성형한 경우 이론밀도의 98%에 가까운 우수한 성형체를 얻었으며, TiC입자가 티타늄 기지 전반에 걸쳐 고르게 분산되어 Ti-TiC 복합재료의 기계적 특성을 향상시켰다. Ti-TiC복합재료의 고온안정성을 고찰하기 위해 $600^{\circ}C$등온열처리한 결과 80시간까지는 경도의 큰 변화없이 열적으로 안정하였다. Ti-20vol%TiC 복합재료를 $700^{\circ}C$에서 고온압축시험을 한 경우 330MPa의 높은 항복강도값을 나타내었다.

• 한국재료학회지
• /
• 제3권2호
• /
• pp.175-184
• /
• 1993

Nd-Fe-B계에 Co와 Al을 첨가한 자석합금을 진공유도용해로에서 제조하여 이들 합금을 단롤법으로 melt-spun시켜 급냉리본을 얻었다. 제작된 급냉리본의 냉각속도에 따른 자기적 성질의 변화를 조사하였고, 최적의 급냉속도에서 제작된 리본을 파쇄하여 resin bond 자석을 제조하였으며, 이들 급냉리본 및 bond자석의 자기적 성질, 미세구조, 결정구조에 관하여 연구, 조사하였다. 이들 급냉리본의 자기적 성질은 급냉속도에 따라 크게 변하였으며 20m/sec전후에서 최적의 자기적 성질을 보였다. 이때의 급냉리본의 미세조직은 Nd-rich의 입계상이 미세한 N$d_2$F$e_14$B결정립을 둘러싼 cell 형의 구조였으며, 특히 Al이 2.1at%첨가된 리본시료에서는 iHc=15.5KOe, Br=7.8KG, (BH)max=8.5MGOe의 자기적 성질을 나타내었다. 최적의 급냉속도에서 제작된 리본을 polyamide resin과 2.5wt%의 비율로 혼합하여 상온에서 성형, 결합시켜 제작한 bond자석에서 보다 현저히 향상되었으며 유지시간이 8분인 경우 iHc=10.8KOe, Br=7.3KG, (BH)max=8.0MGOe의 값을 가졌다. 한편, 자구구조는 maze pattern이 주로 관찰되어 자화용이축인 C축이 배열되었으며 bond자석에서보다 hot-press 자석에서 자구폭이 보다 작았다.

• 펄프종이기술
• /
• 제44권3호
• /
• pp.15-21
• /
• 2012

The optimum dewaxing ratio in dewaxing treatment by the heat and pressure method was investigated by considering aging stability of dewaxed Hanji. Commercial Hanji was coated with beeswax and thermally aged at $150^{\circ}C$ for 24 hours. Then it was dewaxed using the laboratory sheet press equipped with hot plates on both top and bottom sides. Dewaxing ratio was controlled by pressing temperature and time. Four type of dewaxed Hanji samples with different dewaxing ratio were prepared and thermally aged at $150^{\circ}C$. Then the aging stability of dewaxed Hanji samples was evaluated in terms of optical and strength properties. It was found that the aging stability of dewaxed Hanji was superior with higher dewaxing ratio. The result concluded that, in the aspect of aging stability, the coated beeswax in beeswax-treated Hanji shall be completely removed if the coated wax would be dewaxed.

• Journal of the Korean Wood Science and Technology
• /
• 제26권1호
• /
• pp.29-37
• /
• 1998

Alkali-soluble extracts were prepared from medium-sized barks of Radiata pine(Pinus radiata). There are difficulties in the production of extracts with uniform quality and in the preparation of adhesives with suitable viscosity. Ultrafiltration using an Amicon cell was subjected to fractionate extracts according to molecular sizes in order to overcome the above problem. The filtration efficiency was studied by using thin channel filtration systems. Adhesive manufacturing was also examined. Removal of particles greater than 0.45m from the extracts increased both filtration speed (flux) and yields of solids in the filtrates. Ultrafiltration with PM 10 membrane was very effective to fractionate and concentrate the extracts. Stiasny precipitates from the filtrates obtained by PM 10 membrane were very lower than that(83%) of the retentates. This ultrafiltration method was efficient for obtaining high yield purified phenolic compounds(mainly polyflavanoids) and thus important for preparing wood adhesives from barks. The extracts were shown excessive high viscosities at the concentrations required for adhesive formulation, but this high viscosity and short gelation time was reduced by lowering pH of the extracts and addition of urea. The highest bonding strength of plywoods(340g/$m^2$ of adhesive spreads) was achieved with adhesive formulated by 100parts of mixed alkali extracts and urea(70/30,w/w), 10parts of p-formaldehyde and 3.5parts of wheat flour at pH 6, and by hot pressing at the conditions of 12kg/$cm^2$ at $120^{\circ}C$ for 10 minutes.

• 한국재료학회지
• /
• 제29권5호
• /
• pp.277-281
• /
• 2019

The objective of this research is to evaluate the effect of adhesive types on dimensional stability of bamboo-oriented particleboard. The materials used in this research are bamboo tali(Gigantochloa apus J.A & J.H. Schult. Kurz), UF/MDI(8, 10, 12 % level), and MF, MDI, and PF at 7 % level. Particle and adhesive are mixed using a blending machine; then, mat forming and hot pressing processes are performed using adhesive-suitable temperature and time references. MDI resin is set at $160^{\circ}C$ temperature for 5 minutes. PF resin and MF resin are pressed at $170^{\circ}C$ for 10 minutes, and $140^{\circ}C$ for 10 minutes, respectively, while UF/MDI sets at temperature of $140^{\circ}C$ for 10 minutes. The results show that particleboard using PF resin produces the lowest thickness swelling value. The particleboard using UF/MDI resin also produces good response for thickness swelling value. Interesting things happen in that UF/MDI adhesive produces a thickness swelling value better than that of MDI resin. FTIR analysis on particleboard bonded by UF/MDI resin combination shows the presence of carbonyl group C=O vibration on multi substitution of urea at wave number of around $1,700cm^{-1}$.

• 한국분말재료학회지
• /
• 제28권5호
• /
• pp.375-380
• /
• 2021

In this study, we investigate the effect of the duration of mechanical alloying on the microstructures and mechanical properties of ODS ferritic/martensitic steel. The Fe(bal.)-10Cr-1Mo pre-alloyed powder and Y₂O₃ powder are mechanically alloyed for the different mechanical alloying duration (0 to 40 h) and then constantly fabricated using a uniaxial hot pressing process. Upon increasing the mechanical alloying time, the average powder diameter and crystallite size increased dramatically. In the initial stages within 5 h of mechanical alloying, inhomogeneous grain morphology is observed along with coarsened carbide and oxide distributions; thus, precipitate phases are temporarily observed between the two powders because of insufficient collision energy to get fragmented. After 40 h of the MA process, however, fine martensitic grains and uniformly distributed oxide particles are observed. This led to a favorable tensile strength and elongation at room temperature and 650℃.