• Journal of Ocean Engineering and Technology
• /
• v.10 no.4
• /
• pp.103-108
• /
• 1996

To syudy the change of prtential in the mortar-embedded precorroded rebar, a half cell method was adapted. The rebar was corroded by the salt spray and then the rebar embedded in the mortar. A saturated copper sulfate feference electrode was used. The corrosion potential of the rebar in the mortar specimen cured in air was increased, whereas that of the rebar cured in water was decreased with aging. The corrosion potential of the rebar in the mortar was decreased with corroded time by the salt spray. As the mortar thickness covered the rebar was increased, the corrosion potential of the rebar in the mortar was increased.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.9
• /
• pp.24-29
• /
• 1993

The 607 nm GaInP/AlInP distributed bragg reflector (DBR) lasers using the second order gratings period of 184.7 nm were fabricated by gas source molecular beam epitaxy (GSMBE) and the conventional holographic method. GaInP/AlInP DBR lasers show single mode operations up to 1.8 times the threshold currents with a wavelength of 607 nm at 140 K and a wavelength shift of 0.033 nm/K is observed. No mode hopping was found in the temperature ranging from 120 to 165K.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1440-1441
• /
• 2008

In this paper, we investigated the diffraction grating efficiency on AsSeS and Ag-doped amorphous chalcogenide Ag/AsSeS thin film for used to volume hologram. The Chalcogenide film thickness was 0.5um and Ag thin film was varied from 10nm and 20nm. Diffraction efficiency was obtained from (P:P) polarized Diode Pumped Solid State laser(DPSS, 532.0nm: 200mW) beam on AsSeS and Ag/AsSeS thin films. As a results, diffraction grating was not formed at AsSeS thin film but at Ag-doped AsSeS thin film, diffraction grating was formed well compare with the former.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.8
• /
• pp.1-5
• /
• 2014

Conoscopic holography, which consists of two circular polarizers and an uniaxial crystal, is incoherent holographic technology for three-dimensional display and non-contact diagnosis. In this paper, we derive the longitudinal and lateral intensities from point-source hologram made by conoscopic holography. Also, the longitudinal and lateral resolutions of conoscopic holography will be obtained from the longitudinal and lateral intensities, respectively, according to Rayleigh criterion.

• The korean journal of orthodontics
• /
• v.16 no.2
• /
• pp.31-41
• /
• 1986

The purpose of this study is to examine the initial reaction of craniofacial complex to the traction of headgears which are frequent used in dinical practice by using holographic interference method. Changes in the fringe pattern according to the traction conditions (outer bow length, load amount, direction) were compared. Human dry skull was used as experimental material, the results were as follows. 1. The density of fringes increased with an increase in load. 2. Maxillary headgear affected circummaxillary bones-temporal bone, zygomatic bone, nasal bone, frontal bone, sphenoid bone as well as maxilla. 3. The most upward-backward displacement was observed in a high pull head gear $(30^{\circ})$, this is though to be a optimal direction for supressing the growth of the maxilla.

• Journal of Mechanical Science and Technology
• /
• v.18 no.3
• /
• pp.347-356
• /
• 2004

The flexural vibration characteristics of a sandwich beam system with a partially inserted viscoelastic layer were quantitatively studied using the finite element analysis in combination with the sine-sweep experiment. Asymmetric mode shapes of the flexural vibration were visualized by holographic interferometry, which agreed with those obtained by the finite element simulation. Effects of the length and the thickness of the partial viscoelastic layer on the system loss factor (η$\_$s/) and resonant frequency (f$\_$r/) were significantly large for both the symmetric and asymmetric modes of the beam system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.8B
• /
• pp.1048-1056
• /
• 2001

파장분할 다중 광전송 시스템으로의 적용을 위한 홀로그래픽 다채널 역다중화기를 제안하고, 소자 특성에 대한 이론적 예측 및 실험결과를 제시하였다. LiNbO3:Fe 결정에 다중 홀로그래픽 부피 격자채널을 기록하기 위해 각도 다중 기록 및 노출시간 계획을 적용하였으며, 노출시간 계획에 recycling 기법을 적용해 각 채널의 균일도를 향상시켰다. 본 논문에서 제안한 방식을 실험적으로 입증하기 위해 1590nm 파장영역에서 0.8nm 채널 간격을 갖는 8채널 역다중화기를 설계하고 해석하였으며, 실험결과 각 채널은 0.8∼0.92%의 회절효율, 0.38∼0.45nm의 3dB 통과대역, 0.7∼0.89nm의 채널간격 및 -26.98dB 이상의 채널 누화 억제 특성을 관찰하였다.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2012.11a
• /
• pp.46-49
• /
• 2012

본 논문에서는 3차원 입체 비디오처리 기술의 최종목표인 디지털 홀로그램을 생성하는데 필요한 객체의 좌표와 색상정보가 들어있는 같은 시점과 해상도인 RGB 영상과 깊이 영상을 획득하여 가상 시점의 디지털 홀로그램을 생성하는 시스템을 제안한다. 먼저, 가시광선과 적외선의 파장을 이용하여 파장에 따라 투과율이 달라지는 콜드 미러를 사용하여 각각의 시점이 같은 다시점 RGB와 깊이 영상을 얻는다. 카메라 시스템이 갖는 다양한 렌즈 왜곡을 없애기 위한 보정 과정을 거친 후에 해상도가 서로 틀린 RGB 영상과 깊이 영상의 해상도를 같게 조절한다. 그 다음, DIBR(Depth Image Based Rendering) 알고리즘을 이용하여 원하는 가상 시점의 깊이 정보와 RGB 영상을 생성한다. 그리고 깊이 정보를 이용하여 디지털 홀로그램으로 구현할 객체만을 추출한다. 마지막으로 컴퓨터 생성 홀로그램 (computer-generated hologram, CGH) 알고리즘을 이용하여 추출한 가상 시점의 객체를 디지털 홀로그램으로 변환한다.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2012.11a
• /
• pp.50-51
• /
• 2012

본 논문에서는 기존의 홀로그램 행(열)단위 병렬 연산 방식의 고성능 홀로그램 생성기의 하드웨어 자원 량을 효율적으로 사용하기 위해 공통항을 늘려 자원 량을 줄일 수 있는 구조를 제안한다. 하나의 2D 블록의 행과 열에 해당하는 좌표 항을 연산 후 좌표 항을 이용하여 각 블록의 화소 값을 계산한다. 이전 연구에서의 메모리 접근 량을 줄일 뿐만 아니라 이전 연구에 비하여 조합회로는 45% DSP 블록은 90% 감소하여 하드웨어 자원을 효율적으로 사용할 수 있다.

• Journal of the Korean Society of Visualization
• /
• v.4 no.2
• /
• pp.3-5
• /
• 2006

Recently, the next-generation advanced flow visualization techniques such as holographic PIV, aynni.c PIV, echo-PIV, micro/nano-PIV, and X-ray PIV have been introduced. These advanced mea-surement techniques have a big potential as the core technology for analyzing outmost thermo-fluid flows in future. They would be indispensable in solving complicated thermo-fluid flow problems not only in industrial fields such as automotive, space, electronics, aero- and hydro-dynamics. steel, and information engineering, but also in the research fields of medical science, bio-medical engineering, environmental and energy technology etc. Especially, NT (Nano Technology) and BT (Bio Technology) strongly demand these advanced measurement techniques, because it is impossible for conventional measurement methods to observe the nano- and bio-fluidic flow phenomena. In this article, the basic principle of these high-tech flow visualization techniques and their practical applications which cannot be resolved by conventional methods, such as blood flows in a micro-tube, in vivo analysis of micro-circulation, and flow around a living body are introduced as a blue ocean strategy.