• 한국항행학회논문지
• /
• 제26권4호
• /
• pp.219-225
• /
• 2022

본 논문에서는 다중 클래스 인지 라디오 망에서 2차 사용자(SU:secondary user)의 서비스 품질 향상을 위해 RA(restricted access) 기반 동적 스펙트럼 홀 그룹핑에 의한 연결 수락 제어 기법을 제안한다. RA기반 동적 스펙트럼 홀 그룹핑은 본 논문에서 제시한 SU의 다중 클래스 서비스를 위한 일렬 스펙트럼 공유 구조를 사용한다. 다중 서비스 2차 사용자는 실시간 사용자와 비실시간 사용자의 클래스로 구분하고 실시간 사용자에게 자원 사용 우선권을 부여한다. 실시간 사용자가 요구하는 자원의 양은 위너 예측 기법과 RA기반 동적 스펙트럼 홀 그룹핑으로 요구량을 지원하고, 비실시간 사용자에 대해서는 예측 없이 유용한 나머지 홀 자원을 RA기반 동적 그룹핑하여 지원한다. 시뮬레이션을 통하여 2차 사용자의 다중 클래스 연결의 트래픽 특성에 따라 제안된 RA기반 동적 스펙트럼 홀 그룹핑에 의한 연결 수락 제어의 성능을 SU연결의 차단율(손실률)과 자원 이용률에서 비교하고, 다중 클래스 2차 사용자의 원하는 서비스 품질을 만족 시킬 수 있음을 보인다.

• Steel and Composite Structures
• /
• 제46권3호
• /
• pp.403-416
• /
• 2023

This paper summarised and re-examined the theoretical basis of the commonly used design rule developed by Cochrane in the 1920s to consider staggered bolt holes in tension members, i.e., the s²/4g rule. The rule was derived assuming that the term two times the bolt hole diameter (2d₀) in Cochrane's original equation could be neglected, and assuming a value of 0.5 for the fractional deduction of a staggered hole in assessing the net section area. Although the s²/4g rule generally provides good predictions of the staggered net section area, the above-mentioned assumptions used in developing the rule are doubtful, in particular for a connection with a small gauge-to-bolt-hole diameter (g/d₀) ratio. It was found that the omission of 2d₀ in Cochrane's original equation appreciably overestimates the net section area of a staggered bolted connection with a small g/d₀ ratio. However, the assumed value of 0.5 for the fractional deduction of a staggered hole underestimates the staggered net section area for small g/d₀ ratios. To improve the applicability of the above two assumptions, a modified design equation, which covers a full range of g/d₀ ratio, was proposed to accurately predict the staggered net section area and was validated by the existing test data from the literature and numerical data derived from this study. Finally, a reliability analysis of the test and numerical data was conducted, and the results showed that the reliability of the modified design equation for evaluating the net section resistance of staggered bolted connections can be achieved with the partial factor of 1.25.

• Structural Engineering and Mechanics
• /
• 제56권6호
• /
• pp.983-1001
• /
• 2015

This study focuses on the load carrying capacity and the force transfer mechanism of multi-hole perfobond shear connectors in steel-concrete composite structure. The behavior of multi-hole perfobond shear connector is more complicated than single-hole connector cases. 2 groups push-out tests were conducted. Based on the test results, behavior of the connection was analyzed and the failure mechanism was identified. Simplified iterative method and analytic solution were proposed based on force equilibrium for analyzing multi-hole perfobond shear connector performance. Finally, the sensitivity of design parameters of multi-hole perfobond shear connector was investigated. The results of this research showed that shear force distribution curve of multi-hole perfobond shear connector is near catenary. Shear forces distribution were determined by stiffness ratio of steel to concrete member, stiffness ratio of shear connector to steel member, and number of row. Efficiency coefficient was proposed to should be taking into account in different limit state.

• 한국강구조학회 논문집
• /
• 제26권6호
• /
• pp.617-626
• /
• 2014

본 연구에서는 드릴천공 대비 산소토치로 볼트홀을 천공한 강재의 인장강도 평가와 지압이음강도 평가를 위한 실험 연구를 수행하였다. 강재의 인장강도 평가를 위해 앵글과 H-형강으로부터 각각 두께 10mm와 20mm의 드릴 및 산소천공 시험편을 제작하였다. 지압이음강도의 평가를 위해서는 모재와 첨접판을 드릴천공한 강재와 산소천공한 강재를 조합하여 시험체들을 제작하고 볼트이음강도 평가 실험을 수행하였다. 한편, 산소천공 시 열영향으로 인한 볼트홀 주위의 강재 성질의 변화를 평가하기 위해 비커스 경도를 측정하고 그 결과를 제시하였다. 또한, 산소천공 시 볼트홀 주위의 경도 증가에 따른 볼트이음강도의 평가를 위해 수치해석을 수행하였다.

• Steel and Composite Structures
• /
• 제27권3호
• /
• pp.389-399
• /
• 2018

A perforated shear connector group is commonly used to transfer shear in steel-concrete composite structures when the traditional shear stud connection is not strong enough. The multi-hole perforated shear connector demonstrates a more complicated behavior than the single connector. The internal force distribution in a specific multi-hole perforated shear connector group has not been thoroughly studied. This study focuses on the load-carrying capacity and shear force distribution of multi-hole perforated shear connectors in steel-concrete composite structures. ANSYS is used to develop a three-dimensional finite element model to simulate the behavior of multi-hole perforated connectors. Material and geometric nonlinearities are considered in the model to identify the failure modes, ultimate strength, and load-slip behavior of the connection. A three-layer model is introduced and a closed-form solution for the shear force distribution is developed to facilitate design calculations. The shear force distribution curve of the multi-hole shear connector is catenary, and the efficiency coefficient must be considered in different limit states.

• 한국산학기술학회논문지
• /
• 제10권10호
• /
• pp.2831-2836
• /
• 2009

고장력볼트를 이용한 강부재의 연결부에서 마찰력을 초과하는 설계하중이 작용하여 미끄럼이 발생하는 점을 기점으로 볼트와 모재의 전단강도 및 지압강도에 의해 설계하중을 지지하게 된다. 미끄럼량은 볼트의 장력, 접촉면의 마찰계수, 모재구멍내에서 볼트의 위치에 따라 결정되어 질 수 있다. 본 연구에서는 모재 및 덮개판에 대하여 볼트구멍의 크기를 변화시켜 제작된 고장력볼트 체결부에 순수굽힘과 인장력이 작용하는 경우 표준공과 과대공에 따른 미끄럼을 측정하고 비교분석하였다. 표준공을 가지는 경우보다 과대공을 가지는 경우에 $74\sim94%$ 작은 하중에서 미끄럼이 발생하였다. 인장력을 받는 부재에서는 과대공치수가 클수록 미끄럼 하중비가 작게 나타났으며 모재의 과대공치수가 덮개판의 과대공치수보다 미끄럼하중변화와 연관성이 많은 것으로 나타났다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 춘계 학술발표회 논문집
• /
• pp.34-41
• /
• 2006

A 3-dimensional stress measurement system based on the bore hole bottom deformation method, which is one of the stress relief methods, was developed. A pilot bore hole is drilled from the bottom of a bore hole and the stress meter is inserted into the pilot bore hole in the method. The bore hole is advanced as an over coring and the deformations in seven directions are measured by cantilever type-sensors. Using the cantilever type-sensors saves time for hardening of glue. No cable connection between the stress meter and a data logger is necessary since a compact data logger is installed in the stress meter. The accuracy of the stress meter was confirmed by a biaxial test for a Shikotsu welded tuff block although in-situ tests have not been carried out yet.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2009년도 춘계 학술논문 발표대회 학계
• /
• pp.29-32
• /
• 2009

Building foundations for Top-Down construction require a special setting, because the foundations have to be placed way before excavation for the substructure of main building, Usually, the foundation goes into the layer of rock and it is often called rock-pier foundation, Currently, a cage of steel reinforcing bars is inserted to the pre-excavated hole in the rock layer, hanging down from the wide flange steel column above. This paper presents a new method for connecting the prefounded column and the steel cage with a coupler for better connection between the two, The use of a circular Concrete Filled Tube (CFT) as a prefounded column makes it possible to have this type of connection. The details of the connection and application to a Top-Down construction site is also included in this paper.

• Steel and Composite Structures
• /
• 제16권2호
• /
• pp.187-201
• /
• 2014

A new through-beam connection system for a concrete filled steel tube column to RC beam is proposed. In this connection, there are openings on the steel tube while the reinforced concrete beams are continuous in the joint zone. The moment and shear force at the beam ends can be transferred to column by continuous rebar and concrete. The weakening of the axial load and shear bearing capacity due to the opening of the steel tube can be compensated by strengthening steel tube at joint zone. Using this connection, construction of the joint can be made more convenient since welding and hole drilling in situ can be avoided. Axial compression and reversed cyclic loading tests on specimens were carried out to evaluate performance of the new beam-column connection. Load-deflection performance, typical failure modes, stress and strain distributions, and the energy dissipation capacity were obtained. The experimental results showed that the new connection have good bearing capacity, superior ductility and energy dissipation capacity by effectively strengthen the steel tube at joint zone. According to the test and analysis results, some suggestions were proposed to design method of this new connection.

• 한국가구학회지
• /
• 제25권4호
• /
• pp.331-337
• /
• 2014

The purpose of this paper is to evaluate the moment resistance of glulam post-to-base connections by applying quasi-static cyclic loads. The connectors consisted of inserted plates and drifted pins according to the load direction. The connection types employed in this study were total three including two unidirectional types (H, V) and the multi-directional type (M). The moment resistance of 8 mm-plate M-type is compared to 6 mm plate. Total four types of Post-to-base connection are prepared and tested under pseudo-static reversed cyclic loading. Test results showed that the yield moment of multi-directional connection is about 2 times higher than that uni-directional connections. The ductility ratio of multi-directional connection determined by EEEP was higher that that of uni-directional connection. It was becoming higher as the thickness of plate is increased. The Finite Element Analysis was conducted to estimate the stress distribution behavior of tested connections. Results showed the failure of multi-directional type were caused by the split of pined hole and the shear failure of lifted part of post.