• Fire Science and Engineering
• /
• v.26 no.3
• /
• pp.35-39
• /
• 2012

This paper analyzes the combustion diffusion pattern when a water purifier is artificially ignited outside and inside in order to provide data to examine the cause of fire of a water purifier damaged by fire. The analysis result of the combustion diffusion pattern of a water purifier shows that the combustion diffused at a higher speed when it was ignited inside the purifier than when ignited outside. It took approximately 360 seconds for the water purifier to be half-burned when ignited on the outside, and approximately 180 seconds when ignited from inside. That is, it is thought that the internal combustion speed is higher because the internal ignition causes the generated heat to be accumulated and radiated instantly. It was observed that the water purifier damaged by fire caused by external ignition showed a uniform carbonization pattern and the carbide burned down at the bottom were gradually deposited. The water purifier damaged by internal ignition showed a relatively clear boundary of carbonized surface, which formed a V-pattern. The difference in the combustion patterns presents an objective base from which to determine where the fire started. By the time the purifier was half-burned by fire, the built-in fuse had not melted and the power supply protection device did not operate. In addition, as was found in the case of the fuse damaged by a general fire, carbonization occurred at the metal holder, and it is thought that this fact may be used as a basis from which to determine the cause of a fire.

• Korean Security Journal
• /
• no.18
• /
• pp.143-167
• /
• 2009

As of entering the 21st century, a trend in the field of a private security industry among the advanced countries have been increased a qualification system and train session to meet the needs of professionalism. Intensifying the professionalism in Korea, education and train system has been initiated to change but the oligopoly market already formulated due to impractical selection standard and management of education system. Issuing certification and offering basic training through a designated institution for the purpose of improving quality of the private security industry worker, its practical effectiveness were lower than expectation. Rather certification-holder or security agency, institution or truster's rent-seeking behavior have been increased by occupational licensing system. The founded results, which were associated to problems in selecting and educating to the private security guard, in this study were that any verification has been initiated towards dual-system in official approval and structural problems in education system, and non-existence of verification for professionalism and management capability to security agency owner and its upper managerial level. Current a dual system in an officially authorized verification system and completion of security guard credential requested change to an unified official qualification verification system to solve those problems. Ranges of an applicant to the unified official qualification verification system should be extend to the whole population in the private security industry. Moreover, minimization of the dead-weigh loss, which is caused by oligopoly phenomenon while using its market-dominant status, increasement number of designated institution, which allows self-regulating competition, and endowment of autonomy, which is in selecting education and agency, were requested to solve the problems in selecting and educating to the private security guard. In order to minimize stated problems while maintaining objectiveness, a new manage and supervise institution, which is called a 'private security industry committee', should be establish. The private security industry committee is a formation of governance network which are participated from professional group to civil organization.

• Applied Microscopy
• /
• v.38 no.4
• /
• pp.285-291
• /
• 2008

We have evaluated the effects of experimental factors on transmitted electron beam intensities for quantitative analysis in electron tomography. For the correct application of Beer's law in electron tomography, the transmitted beam intensity should reflect the net effect of mass properties on beam path. So, the any other effects of the objective aperture and the specimen holder on beam path should be removed. The cut-off effects of objective aperture were examined using Quanti-foil holey carbon film and a transmission electron microscope operated at 120 kV. The transmitted beam intensities with $30{\mu}m$ objective aperture dropped about 16.7% compared to electron beam intensities without the objective aperture. Also, the additional losses of about 14.2% at high tilt angles were occurred by cut-off effects of the objective apertures. For the precise quantitative analysis in electron tomography, the effect of the objective aperture on transmitted electron beam intensities should be considered. It is desirable that 2-D tilt series images are obtained without the objective aperture for correct application of Bee's law.

• Progress in Medical Physics
• /
• v.14 no.2
• /
• pp.99-107
• /
• 2003

This study was performed to prepare the verification film for localizing beam-target position with the Photon Knife radiosurgery system (PKRS) using linear accelerator(Mitsubishi, Model ML-15MDX). We developed a laser calibration system using a reticle of transparent lucite to detect Inlet and outlet beams. We verified fixation of the second collimator with film mounted on a holder in the shape of an octagon block 5cm apart from the isocenter. The film was exposed to photon beams of linear accelerator at an interval of 45 degrees during the gantry movement. There were no shifts in the beam of the second collimator during gantry movement. We used a position marker which is designed a head-shaped small lead block and a 10 mm in diameter of steel bead in the plastic tube. The position marker helped to verify the beam directions with patient position in multi-arc and trans-multi-arc of PKRS The verification of beam alignments showed an average 0.8$\pm$0.26 mm discrepancy in LINAC-gram images of PKRS. In our study, the couch movement was $\pm$5 mm laterally, while it shook $\pm$ 2 mm toward the couch axis. The couch, however, was immediately returned to the initial site after shaking. Thus, we postulate that the beam-target position(s) should be verified with LINAC-gram in a stereotactic radiosurgery system to achieve the accuracy of beam-target alignment.

• Korean Journal of Agricultural Science
• /
• v.20 no.1
• /
• pp.88-101
• /
• 1993

This study is aimed at evaluating the present management status of the rural special production area development projects and identifying managerial problems to propose new direction of the political countermeasures for the projects. In the con text of implementing the five year's economic developent plans for the past three decades, agricultural production and farm-household income have also been grown rapidly. However the income gap between rural and urbarn laborer, as an internal problem, has widened during the decades and the UR problems concerning free trade of agricultural products, as an external problems, are now agonizing the small-holder farm economy in Korea. The internal and external farm problems could be solved through improvement of agricultural structure and provision of off-farm jobs for farm household income increase. As a part of the off-farm income sources, the rural special production area development projects have propelled by the government throughout the country. The main problems to be solved for the successful implementation of the projects are as follows : 1. Present loan amount by the financial fund was estimated at 6-7% of the total installation costs required. To expand and implement the project successfully, enough financial credit support with favorable terms and conditions have to be considered by the government. 2. The operation patterns of the special production area development project should be recommended from the view point of cooperative and private operation to maximize farm household incomes including profits, marketing charges and dividens. 3. Improvement of the marketing channel of the products and marketing information through TV program and other mass communication should be implemented strongly to promote marketsales by the financial supports of the government. 4. In connection with the off-farm income increase, the population migrating to urban area in outside Chungnam province equivalent to 10-12 thousand persons with age of 20-49 years should be taken into account politically to be employed in the projects in the province. 5. Surplus farm labors should be created by means of improvement of agricultural structure including large farm management with farm mechanization and job opportunities have also to be provided in connection with the rural special production area development projects. The two imminent subjects are the prerequisites to increase off-farm incomes for the farmers living in Chungnam province. 6. Required credit supports for investment and operation costs of the projects should be taken actions by the government.

• Fire Science and Engineering
• /
• v.25 no.6
• /
• pp.21-26
• /
• 2011

The purpose of this paper is to present the damage patterns of cellular phone (SCH_W830) batteries according to energy sources and have them utilized as data for the settlement of disputes between manufactures and consumers. The reliability was secured by maintaining the ambient temperature and humidity at $22{\pm}2^{\circ}C$ and 40~60 %, respectively. The voltage of the battery used for the tests was measured to be 4.18V between positive pole (+) and negative pole (-)(1), and 4.19 V between positive pole (+) and negative pole (-)(2). This study applied the Korean Industrial Standard (KS) to the flammability test of cellular phones due to a general flame applied to them and found that no damage occurred to the built-in battery even though the flame was applied to the cases of cellular phones for 30 seconds. From the results of immersing the cellular phones in the saline solution (NaCl, 0.9 %) for 180 seconds, it was found that there was a trace of carbonization and melting due to the heat caused by leaking current. It can be seen that when the cellular phones were heated for 70 seconds using a microwave oven (MWO), the areas containing the metal holder, recharging connector, antenna, etc., were melted and discolored and that other areas showed no particular problems. That is, while the external carbonization of cellular phones, built-in metals and dielectric materials, and damage and deformation of the battery terminal block, etc., occurred differently depending on the types of energy sources, the voltage showed comparatively constant characteristics. Therefore, it is thought to be possible to attribute the cause of damage to the battery by performing analysis taking into consideration comprehensively the characteristics of the flame spread pattern as well as the melting and deformation of metals.

• Korean Business Review
• /
• v.11
• /
• pp.195-216
• /
• 1998

Ownership of an asset can be identified with the right to exercise "residual control" where the contract is silent about decision rights, or with the right to receive any "residual returns" that remain after contractual. obligations are fulfilled. Although the concept of "ownership" seems reasonably clear in many of the cases, the concepts of residual control and the residual returns that define ownership are actually quite elusive. For large corporations, there is really no single individual who owns both the residual returns and the residual control. Despite the limited qualifications, ownership is clearly. the most common and effective meas to motivate people to create, maintain, and improve the value of assets. In this paper, we try to clarify the relationships among financial structure, ownership, and corporate control with the concept of ownership defined as the residual control and the residual returns, Financial securities are not just claims to part of a firm's net income. They give the security holder certain rights. A careful matching of rights of control and returns can create incentives that increase total value of the firms. In the corporate firms, managers, lenders, and shareholders have different interests. And the financial structure affects how different those interests are and what decisions management will make. Managers are, in general, better informed than investors about the firm's prospects. The financial decisions by managers may affect investors' beliefs and, therefore, the price of shares and the value of the firm.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.31 no.4
• /
• pp.300-305
• /
• 2005

Purpose: For the reconstruction of maxillofacial defect created by trauma, infection, or tumor etc, the role of microvascular anastomosis or vessel graft has been increased. Many methods has been tried to increase the success rate of microvascular anastomosis. Various anticoagulants and thrombolytic agents have been used to reduce the failure rate of microvascular anastomosis and avoid re-operation. Many drugs, however, have been used in the limited cases because most of these drugs may cause complications, such as allergy, fever or systemic bleeding. This study was performed to evaluate the influence of the Argatroban on patency and thrombosis in microvascular anastomosis when it is used for local irrigation or general administration. Materials & methods: Eight mature rabbits, weighing 2kg, were used. After exposing both femoral veins, the artificial thrombotic model was made by crushing injury using a smooth needle holder, and the transverse incision were made on femoral vein. The animals were divided into 4 groups according to Argatroban administration methods; control group (n=4), topical irrigation of lumen with saline solution; experimental group 1 (n=4), topical irrigation of lumen with Argatroban saline solution; experimental group 2 (n=4), topical irrigation of lumen with heparin followed by intravenous injection of Argatroban; experimental group 3 (n=4), topical irrigation of lumen with Argatroban followed by IV of Argatroban. Microvascular anastomosis was done with 10-0 Ethilon. The patency was evaluated by empty-and-refill test 30 minutes and 3 days after microanastomosis. The thrombus formation was examined 3 days after microanastomosis by surgical microscope. The histologic findings were also examined. Results: 1. Thirty minutes after microvascular anastomosis, the patency of all experimental groups was better than that of control group, but there was no significant difference among groups. 2. Three days after microvascular anastomosis, the patency of all experimental groups was more improved than that of control group (p<0.05). There was no significant difference among experimental groups. 3. Three days after microvascular anastomosis, the amount of thrombus in all experimental groups was less than that of control group (p<0.05). There was no significant difference among experimental groups. 4. Histologically, a lot of luminal thrombus was observed around sutured area in control group. Few luminal thrombus was observed in all experimental groups. The necrotic changes were observed on the sutured vein wall in all specimens. Conclusion: These results indicate that topical irrigation and/or intravenous administration of Argatroban is effective in improving patency and preventing thrombus formation after microvascular anastomosis.

• Journal of the Korean Institute of Gas
• /
• v.20 no.4
• /
• pp.78-84
• /
• 2016

In this work, finite element investigations were carried out to optimize reverse drawing process design for manufacture of high-capacity aluminum liner used in fuel cell vehicle. The tensile tests with aluminum alloy Al6061 annealed at $350^{\circ}C$ were carried out to obtain the flow stresses. In order to estimate more accurate flow stresses after necking, the flow stresses were estimated from the comparison of load vs. displacement curves which were obtained from experimental and simulation results of tensile tests. In case of finite element analyses of reverse drawing processes, it was focused on the effects of process designs such as punch and die designs, blank holding force, drawing ratio and the clearance between the punch and blank holder on the generation of wrinkle and fracture of the blank and partially heated punch. However, it was revealed that experimental results still show the fracture at the end of 2nd drawn cup, although partially heated punch is used. Nevertheless, the drawn cup can be used because the sufficient length of the drawn cup for the next flow forming process and spinning process was obtained.

• Progress in Medical Physics
• /
• v.13 no.3
• /
• pp.114-119
• /
• 2002

A immobilizing device that is essential for correct lung and lens shielding with homogenous dose distribution in fractionated total body irradiation was developed and it's efficiency was evaluated. The main frame was made of stainless steel bar (5 cm in diameter) to withstand up to 230 cm in height and 100 kg in weight to prevent any injury even in unconsciousness condition. The saddle was designed to adjust the body weight and hight of standing patients. Chest and back supporter were made of 1 cm acryl which could fix the lung block and cassette holder. Leather and sponge pedding were used for head rest to keep patients comfortable. The device was strongly fixed by specially designed bolts on the bottom panel which was made of 1 cm stainless steel and 10 cm thick wooden board. Precise manipulation ($\pm$2 mm) was possible by upper two pulleys and side handles. Average four minutes twenty five seconds were needed for exact setting in fractionated TBI. No significant difference of lung block location on repeated verification films was confirmed and relatively homogeneous dose distribution was measured in rando phantom experiments and patient treatments ($\pm$5%). This immobilizing device was very efficient to keep correct position of patients, which is essential for better result and less complication in fractionated TBI.