• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.924-926
• /
• 2005

This paper presents an excellence start-up performance drive system of Switched Reluctance Motor(SRM) for hoist. At first, the SRM design method of Hoist drive is expounded, and suitable Digital control arithmetic of SRM Hoist drive is advanced in the paper. Finally, some correlative experimentation has been finished, and the SRM Hoist drive has been confirmed in the experimentation.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.11
• /
• pp.561-568
• /
• 2005

This paper proposes a method that distributes the load power and stores the regenerated energy for a hoist-load system using the supercapacitor, an energy storage device. The crane, which is a representative hoist-load system, operates in two modes. The first is the hoist-up mode in which the load container is lifted up: the maximum power is required at the end of acceleration. The second is the hoist-down mode in which the load container is lifted down; the regenerated energy is wasted by the resistor In this paper, the supercapacitor stores the regenerated energy in the hoist-down operation and supplies the peak power demand in the hoist-up operation. The same structure as the commercially available three-phase inverter is proposed as a bidirectional do-dc converter to charge and discharge the supercapacitor. A power control algorithm is proposed to optimize the load sharing between the generator and the supercapacitor. Using the proposed method, it is effected that the generator size can be cut down to one third of the original one; it leads to the reduction of the fuel consumption, noise and air pollution. Simulation and experimental results verify the effectiveness of the Proposed method.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.145-146
• /
• 2008

• Transactions of The Korea Fluid Power Systems Society
• /
• v.4 no.1
• /
• pp.1-6
• /
• 2007

The typical hydraulic system of hoist is composed of a hydraulic supply unit, a directional control valve, two pilot operated check valves, two flow control valves. The capacity coefficients of flow control valves should be adjusted for the hoist to operate at moderate speed and minimize the hydraulic energy loss. However, it is difficult to adjust the four capacity coefficients of flow control valves by trial and error for optimal operation. The steady state model of the hoist hydraulic system is derived and the optimal capacity coefficients of flow control valves are obtained using the complex method that is one kind of constrained direct search method.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.5 no.1
• /
• pp.13-19
• /
• 2008

The typical hydraulic system of hoist is composed of a hydraulic supply unit, a directional control valve, counter balance valve, and flow control valves. The flow capacity coefficients of flow control valves should be adjusted so that the hoist is operated at moderate speed and the hydraulic energy loss is minimized. However, it is difficult to adjust the flow coefficients of flow control valves by trial and error for optimal operation. Here, the steady state model of the hoist hydraulic system including the differential cylinder circuit is derived and the optimal flow capacity coefficients of flow control valves are obtained using the complex method that is one kind of constrained direct search method.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1486-1488
• /
• 2005

본 논문에서는 수퍼캐패시터(Supercapacitor 이하 수퍼�L)를 이용하여 엔진 발전기를 전원으로 하는 권상부하 시스템의 부하전력 분배와 회생에너지의 저장 기법을 제안한다. 대표적인 권상부하 시스템인 크레인의 경우, 크게 두가지 운전모드로 동작한다. 첫번째 운전모드는 부하를 들어올리는 동작(Hoist-Up)으로서 가속 종료시점에서 최대전력을 소모한다. 두번째 운전모드는 부하를 내리는 동작(Hoist-Down)으로서 이때 희생되는 전력은 일반적으로 저항을 통하여 소모된다. 본 논문에서는 에너지 저장장치의 하나인 수퍼�L을 이용하여 Hoist-Down 운전에서 희생되는 에너지를 저장하고 Hoist-Up 운전에서 필요한 전력을 보조하도록 하였다. 수퍼�L의 충방전을 위하여 상용 3상 인버터와 동일한 구조를 가지는 DC-DC 컨버터를 제안하였다. 또한 발전기와 수퍼캐패시터의 Load Sharing을 최적화하기 위한 알고리즘을 제안하였다. 제안한 방법을 이용하면 디젤엔진 발전기의 크기를 대폭 줄일 수 있고 따라서 연비의 개선, 소음 및 공해의 감소를 기대할 수 있다. 제안한 방법의 타당성을 검증하기 위하여 시뮬레이션과 실험을 수행하였다.

• Structural Engineering and Mechanics
• /
• v.49 no.3
• /
• pp.311-327
• /
• 2014

The safety relating to leakage of water and pitch instability of ship chambers of the full balanced hoist vertical shiplifts has been the focus of adoption of the type of vertical shiplifts. This paper aims to remove the doubts through theoretical and engineering researches. The leakage and pitch stability of ship chambers of full balanced hoist vertical ship lifts are investigated on the basis of theoretical analysis and exploration of engineering measures. Regarding the issue of leakage of ship chambers, a mathematical model on leaking process is built and corresponding formula and coping measures are obtained which can be applied in control program of ship lifts by linking with monitoring. The concept of safety grade is put forward to seek the best technical and economic index and the corresponding technical measures are for different grades of ship lift is suggested. For the issue of pitch instability, a methodology of combining theoretical deduction and summary of achievements of design and operation of the type of the full balanced hoist shiplifts is adopted, and the formula for design about pitch stability of ship chambers is derived.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1622-1625
• /
• 2003

RMQC, rail mounted quay crane, lifts and moves large container by means of hoist and trolley motion on the dock. Our company is trying to develop advanced RMQC applying the concepts of elevator hoist and container conveyer for the automation and high efficiency in handling the boxes. Prior to the development of new products, it is necessary to check the capacity of conventional crane for reference. The program simulates container-handling rates and gives some design factors for the conventional cranes.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2003.11a
• /
• pp.224-228
• /
• 2003

The basic Principles and methods of the on-line monitoring of tribology parameters (friction coefficient and wear allowance) and fault diagnosis for the hoist disc brake system were introduced, the method were based on the spring force and oil pressure of the brake system and the hoist kinematics parameters. The experiment on the monitoring and diagnosis of hoist brake system were carried out. The research results showed: the monitoring and diagnosis methods are feasible.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1109-1113
• /
• 2004

RMQC, rail mounted quay crane, lifts and moves large container by means of hoist and trolley motion on the dock. Our company is trying to develop advanced RMQC applying the concepts of elevator hoist and container conveyer for the automation and high efficiency in handling the boxes. Prior to the development of new products, it is necessary to check the capacity of the new systems using simulation program. The program simulates container-handling rates and gives some design factors for the new-type cranes.