• Journal of Magnetics
• /
• v.21 no.1
• /
• pp.72-77
• /
• 2016

Although the initial cost of permanent-magnet linear synchronous motors is high owing to the installation of armatures over the full length of the transportation lines, linear motors are useful for transportation systems because of their high speed, acceleration, and deceleration. For these reasons, research into reducing the cost of linear motors is necessary, and a stationary distributed-armature system has been suggested for installing armatures in sections where acceleration and deceleration of the mover are required. However, each armature has ends that significantly increase the cogging force, resulting in the increase in the thrust ripple of the mover. Therefore, in order to improve the thrust ripple of the system, the present study aims to provide auxiliary teeth on both ends of the armature to achieve an optimal design through an analysis of the contribution ratio with respect to factors regarding the design of the experiment and the objective function.

• Proceedings of the KSR Conference
• /
• 2009.05b
• /
• pp.267-274
• /
• 2009

To predict efficiency of Interior Permanent Magnet Synchronous Motors(IPMSM) and to cope with the demagnetization risk of permanent magnets used in the IPMSM, accurate iron analysis of the IPMSM is very important at the motor design stage. In the analysis, we calculate the operation condition such as rotor speed and current angle. and then, we analyzed the iron loss of the machine for electric vehicle according to its driving condition. From the analysis results, it was shown that the harmonic iron losses of stator are larger than before at field-weakening region. In addition, it was revealed that rotor iron loss mainly induced by stator slot-ripples is independent of current angle and only varied according to the speed.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.1
• /
• pp.118-123
• /
• 2013

This paper presents performance comparison between concentrated winding and distributed winding of IPMSM (Interior Permanent Magnet Synchronous Motors) which is recently used for light-weight railway applications. Motors are designed on various schemes and analyzed by using FEM (Finite Element Method) instead of EMCNM (Equivalent Magnetic Circuit Network Method) in order to take into account saturation and non-linear magnetic property. The overall performance such as torque, torque ripple, losses, demagnetization, efficiency, power density and so on are investigated in detail at the rated and maximum operating speed. The results of the analysis found that both concentrated and distributed winding IPMSMs are promising candidates for high power railway traction motor.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.4
• /
• pp.209-215
• /
• 2006

Recently Permanent Magnet Linear Synchronous Motors(PMLSMs) are widely used for many linear transportation applications. The PMLSM has many advantages such as simple structure, high speed and thrust. However, especially in short primary type PMLSM, there exists very large detent force, which makes the thrust force ripple, undesired vibration and noise. The detent force is composed of the Cogging force and the End force. The Cogging force comes from the interaction between the permanent magnets and interior teeth of the stator. And the End force acts on the exterior teeth of the stator by the permanent magnets. Usually End force is larger than Cogging force, so the detent force is drasically reduced only by reducing the End force. This paper shows the End force is minimized by optimizing the stator length and chamfering the shape of the exterior teeth of the stator.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.5
• /
• pp.1067-1072
• /
• 2012

Recently, linear motors have been widely researched and have been increasingly used in various industrial applications. Especially, permanent magnet linear synchronous motors(PMLSMs) have been getting the spotlight in the transportation system. A PMLSM is structurally simple and has a lot of merits such as high speed, high thrust force, etc. However, in case of a long stator system which arranges armature to the full length of transportation lines, a PMLSM has some disadvantages such as the material cost increase and long manufacturing time. Hence, in order to overcome these problems, the PMLSM with stationary discontinuous armature structure and concentrated windings was proposed. However, this method occurs undesirable cogging force by outlet edge effect. The cogging force causes thrust force ripples and generates noise and vibration. Therefore, in this paper, we proposed installation method of auxiliary pole PMLSM with concentrated winding applying bifurcating in order to reduce cogging force by the outlet edge when the armature is placed in a discontinuous arrangement. Also, we have examined characteristics of outlet edge cogging force using 2-D finite element analysis(FEA).

• Journal of Power Electronics
• /
• v.15 no.3
• /
• pp.753-762
• /
• 2015

This paper presents a nonlinear sliding mode control (SMC) scheme with a variable damping ratio for interior permanent magnet synchronous motors (IPMSMs). First, a nonlinear sliding surface whose parameters change continuously with time is designed. Actually, the proposed SMC has the ability to reduce the settling time without an overshoot by giving a low damping ratio at the initial time and a high damping ratio as the output reaches the desired setpoint. At the same time, it enables a fast convergence in finite time and eliminates the singularity problem with the upper bound of an uncertain term, which cannot be measured in practice, by using a simple adaptation law. To improve the efficiency of a system in the constant torque region, the control system incorporates the maximum torque per ampere (MTPA) algorithm. The stability of the nonlinear sliding surface is guaranteed by Lyapunov stability theory. Moreover, a simple sliding mode observer is used to estimate the load torque and system uncertainties. The effectiveness of the proposed nonlinear SMC scheme is verified using comparative experimental results of the linear SMC scheme when the speed reference and load torque change under system uncertainties. From these experimental results, the proposed nonlinear SMC method reveals a faster transient response, smaller steady-state speed error, and less sensitivity to system uncertainties than the linear SMC method.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.67-71
• /
• 2020

In this study, a simulation model of the harmonic injection sensorless control technique is proposed. This model is suitable for the sensorless technique of low-speed area operation of motors. The motor of this model is permanent magnet motor. For sensorless control, 1kHz square wave is injected. The change in motor constant according to rotor position is realized by having different d-q inductance values. Sensorless techniques is implemented through functions of Simulink and models provided by Simulink libraries. It is shown that the harmonic component contained in the current is extracted using a filter, and the angle of the permanent magnet of the motor is detected using the extracted waveform. The validity of the simulation model is demonstrated through the estimated motor angle waveform and the related waveforms of the motor control applied to the 1kW permanent magnet motor.

• ETRI Journal
• /
• v.37 no.6
• /
• pp.1176-1187
• /
• 2015

This work proposes a highly efficient sensorless motor driver chip for various permanent-magnet synchronous motors (PMSMs) in a wide power range. The motor driver chip is composed of two important parts. The digital part is a sensorless controller consisting mainly of an angle estimation block and a speed control block. The analog part consists of a gate driver, which is able to sense the phase current of a motor. The sensorless algorithms adapted in this paper include a sliding mode observer (SMO) method that has high robust characteristics regarding parameter variations of PMSMs. Fabricated SMO chips detect back electromotive force signals. Furthermore, motor current-sensing blocks are included with a 10-bit successive approximation analog-to-digital converter and various gain current amplifiers for proper sensorless operations. Through a fabricated SMO chip, we were able to demonstrate rated powers of 32 W, 200 W, and 1,500 W.

• Journal of Industrial Technology
• /
• v.34
• /
• pp.15-20
• /
• 2014

Recently, PMSMs(Permanent Magnet Synchronous Motors) have become increasingly popular in various high-performance motor drive applications. However, the high-performance drive of PMSMs needs a position sensor such as a resolver, which increases not only the price of the system but also reduces the system reliability. This paper is on the implementation of sensorless control of a SPMSM, which drives a fan for cooling in appliances. In this paper, the rotor position for high-performance drive of a SPMSM is derived from back electromotive force (EMF) information proportional to the rotor speed. Also, the initial rotor position information for start-up is estimated from a saturation phenomenon of inductance. The validity of the proposed sensorless drives was confirmed by the experiment on the SPMSM drive systems for cooling fans of refrigerators and laptop computers.

• Proceedings of the KIPE Conference
• /
• 2003.07a
• /
• pp.461-466
• /
• 2003

This paper presents the speed control of the surface-mounted permanent-magnet synchronous motors (SMPMSM) for the elevator drive. The elevator motor needs to be a compact and slim type. Essentially, the proposed scheme uses a vector control algorithm for a speed and torque control. This system is implemented using a high speed 32-bit DSP (TMS320C31-50), a high-integrated logic device FPGA (EPF10K10-Tl144-3) to design compactly and Inexpensively The proposed scheme is verified through digital simulation and experiments for a three-phase 13.3kW SMPMSM as a MRL(MachineRoomless) elevator motor ill the laboratory. Finally, experiment of the test tower was performed with a 48kW PWM converter-inverter system for a high- speed elevator .