• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.2
• /
• pp.333-338
• /
• 2008

In this paper, a new NMOS current-mirror type bridge rectifier for driving RFID chips, whose minimum input voltage required to obtain the effective DC output voltage is low enough and whose power dissipation can be reduced than that of conventional one, is proposed. The designed rectifier is able to supply high enough and well-rectified DC voltages to drive RFID transponder chips for the frequency range of 13.56 MHz HF(for ISO 18000-3), 915 MHz UHF(fur ISO 18000-6), and 2.45 GHz microwave(for ISO 18000-4). Output characteristics of the proposed rectifier are analyzed with the high frequency equivalent circuit. And the circuitry method for effective reducing of the gate leakage current due to the increasing of operating frequency is also proposed theoretically. Using this method, the power consumption of $100\;{\mu}W$ and the DC output voltage of 2.13V for 3V peak-to-peak input voltage and $45\;K{\Omega}$ load resistance are obtained. Compared to conventional one, the proposed rectifier operates in more stable and shows superior characteristics in UHF and microwave frequencies.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.5 no.1 s.9
• /
• pp.13-19
• /
• 2006

In this paper, a broadband Microwave Power Module(MPM) operating at 7 - 11 GHz is designed and fabricated. The MPM consists of a SSA (Solid State Amplifier) and a conventional TWT (traveling Wave Tube). This combined module takes advantage of a low noise and high gain of SSA. The computer modeling and simulation of the SSA are designed by the use of the ADS (Advanced Design System) software. The SSA is designed by configurating the CSSDA (Cascaded Single Stage Distributed Amplifier). The broadband MPM is measured to be noise figure 8.3 - 10.02 dB at 7 - 11 GHz bandwidth, output power of 38.12 dBm at 9 GHz.

• Journal of the Semiconductor & Display Technology
• /
• v.17 no.2
• /
• pp.20-25
• /
• 2018

In this paper, we have designed circularly polarized array antenna for 5.8GHz microwave wireless power transmission. To obtain high antenna gain, we studied a single patch antenna, a $2{\times}1$ array antenna, a $2{\times}2$ array antenna, a $2{\times}4$ array antenna, and a $4{\times}4$ array antenna. Commonly, characteristics of each antenna have a frequency of 5.8 GHz and Right Hand Circular Polarization(RHCP) of circular polarization. Also, the results were obtained with the design to each antenna that the return loss was less than -10dB and the axial ratio was less than 3dB. The gain of the antennas was 6.08dBi for a single patch antenna, 9.69dBi for a $2{\times}1$ array antenna, 12.99dBi for a $2{\times}2$ array antenna, 15.72dBi for a $2{\times}4$ array antenna and 18.39dBi for a $4{\times}4$ array antenna. When the elements of the array antenna were increased, it was confirmed that it increased by about 3dBi.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.22-22
• /
• 2009

The silver thick film has been used in many industries such as display, chip, solar cell, automobile, and decoration with conventional heating. The silver thick film is fired with optimal time and temperature. However, decreasing the fabrication time is required due to high production power. Furthermore, there is a problem that silver in electrode is diffused throughout any substrates. For inhibiting the Ag diffusion and long fabrication time we considered a microwave heating. We investigated firing of silver thick film with conventional and microwave heating. The temperature of substrate was measured by thermal paper and the temperature of substrate was under $100\;^{\circ}C$ The shrinkage of electrode was measured with optical microscopy and optical profilometry. The shrinkage of electrode heat treated with microwave for 5min was similar to the that fired by the conventional heating for several hours. After firing by two types of heating, the diffusion of silver was determined using a optical microscope. The microstructure of sintered silver thick film was observed by SEM. Based on our results, the microwave heating should be a candidate heating source for the fabrication electronic devices in terms of saving the tact time and preventing the contamination of substrate.

• Korean Chemical Engineering Research
• /
• v.56 no.1
• /
• pp.66-72
• /
• 2018

Corn stover is known as a good candidate for a functional food ingredient when the main lignocellulosic material, lignin, is used as bioactive materials as form of polyphenolic compounds. The purpose of this study was to determine the microwave extraction conditions under which total phenolic compounds (TPC) and flavonoid contents of corn stover were maximized. Microwave-assisted extracts using sulfuric acid ranging from 0 to 1.0 mol with extraction time between 40 and 240 sec were conducted by using response surface methodology (RSM). Microwave power showed significant effects (p<0.05) and the concentrations of TPC and flavonoids increased with increased level of microwave power and extraction time. The optimum conditions for corn stover extraction were determined as 698.6 W, 240 sec, and 0 mol sulfuric acid, and the predicted value of TPC and flavonoid is 82.4 mg GAE/g DM and 18.1 mg/g DM, respectively. Microwave extraction was evaluated as an economic process with low energy consumption, short extraction and high extraction yield of bioactive including TPC and flavonoids compared to conventional extractions.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1530-1533
• /
• 2005

Total 12 units of high power klystron-modulator systems as microwave source is under operation for 2.5-GeV electron linear accelerator in Pohang Light Source(PLS) linac. RF power and beam power of klystron are precisely measured for the effective control of electron beam. A precise measurement and measurement equipment with good response characteristics are required for this. Input power of klystron is calculated from the applied voltage and the current on its cathode. Tiny measurement error severely effects RF output power value of klystron. Therefore, special care is needed to measure precise beam voltage. Capacitive voltage divider(CVD) unit is intended for the measurement of beam voltage of 400 kV generated from the pulsed klystron-modulator system. Main parameter to determine the standard capacitance in the high arm of CVD is dielectric constant of insulation oil. Therefore CVD should be designed to have a minimum capacitance variation due to voltage, frequency and temperature in the measurement range. This paper will discuss the analysis of capacitive voltage divider for a pulsed high-voltage measurement, and the empirical relations between capacitance and oil temperature variation.

• Electronics and Telecommunications Trends
• /
• v.36 no.3
• /
• pp.53-64
• /
• 2021

As the 5G service market is expected to grow rapidly, the development of high-power, high-efficiency power amplifiers for the 5G communication infrastructure is indispensable. Gallium nitride (GaN) is attracting great interest as a key device in power devices and integrated circuits due to its wide bandgap, high carrier concentration, high electron mobility, and high-power saturation characteristics. In this study, we investigate the technology trends of Ka-band GaN radio frequency (RF) power devices and integrated circuits for operation in the millimeter-wave band of recent 5G mobile communication services. We review the characteristics of GaN RF high electron mobility transistor (HEMT) devices to implement power amplifiers operating at frequencies around 28 GHz and compare the technology of foreign companies with the device characteristics currently developed by the Electronics and Telecommunication Research Institute (ETRI). In addition, the characteristics of Ka-band GaN monolithic microwave integrated circuit (MMIC) power amplifiers manufactured using various GaN HEMT device technologies are reviewed by comparing characteristics such as frequency band, output power, and output power density of integrated circuits. In addition, by comparing the performance of the power amplifier developed by ETRI, the current status and future direction of domestic GaN power devices and integrated circuit technology will be discussed.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.11
• /
• pp.1934-1939
• /
• 2006

Current digital communication system is selecting very various digital Modulation way. Need linear power amplifier necessarily to reduce interference for contiguity channel maximum in this communication system and at the same time, power amplifier of high efficiency is required. In this paper Compare with result of equilibrium power amplifier that design Doherty power amplifier of way that linearity and efficiency are improved at the same time through simulation optimization techniques and at the same time design through simulation, efficiency 20% linearity showed 10dB that is improved.

• Analytical Science and Technology
• /
• v.25 no.5
• /
• pp.265-272
• /
• 2012

Okamoto cavity was modified to generate high power (2.45 GHz, 2 kW) He, N2 and Ar plasmas with WR-340 waveguide. Many factors which influence to the plasma generation were optimized and investigated for the spectroscopic properties of the He plasma generated. Some of the important factors are the diameter of the inner conductor, the distance between the inner and outer conductors and the distance between the tip of the inner conductor and the torch. After optimization for the He, two torches (a commercial mini torch for ICP and a tangential flow torch made locally) were compared and showed similar results for the helium plasma gas flow of 25 L/min~30 L/min. A tall torch (extended) was used to block the air in-flow and reduced the background intensity at 340 nm region (NH band). Emission intensity was measured for determination of halogen element in the aqueous solution with power and carrier gas flow rate. Electron number density and the excitation temperature were on the order of $3.67{\times}10^{11}/cm^3$ and 4,350 K, respectively. These values are similar or a bit smaller than other microwave plasmas. It has been possible to analyze aqueous samples. The detection limit for Cl (479.45 nm) was obtained to be 116 mg/L and needs analytical optimization for the better performance.

• Electronics and Telecommunications Trends
• /
• v.29 no.6
• /
• pp.1-13
• /
• 2014

GaN(Gallium Nitride)는 3.4eV의 넓은 에너지 갭으로 인하여 고전압에서 동작이 가능하고, 분극전하를 이용한 캐리어 농도가 높아 높은 전류밀도와 전력밀도를 얻을 수 있으며, 높은 전자 이동도와 포화 속도로부터 고속 동작이 가능하여 고주파 고출력 고효율 소형의 전력증폭기 소자의 재료로 적합하다. 본고에서는 민수 및 군수 겸용 Ku-대역 및 Ka-대역 GaN 고출력 전력증폭기(SSPA: Solid-State Power Amplifier)와 관련된 GaN 전력증폭 소자, GaN 전력증폭기 MMIC(Microwave Monolithic Integrated Circuit), 내부정합 패키지형 GaN 전력증폭기 및 GaN SSPA에 대하여, 국내외 특허 기술동향과 연구개발 기술동향을 중심으로 고찰하고자 한다. 국외의 GaN 고주파 고출력 전력증폭기 기술의 연구동향이나 특허동향을 심층분석하여 연구개발에 활용하고자 한다.