• Proceedings of the KIEE Conference
• /
• 2005.10b
• /
• pp.508-510
• /
• 2005

In this paper, we have studied for the current control method with high accuracy for the high power LED driver that is necessary to the lighting system using LEDs. The control performance of LED driver can be improved with the adjustment of current control boundary by introducing D/A converters for setting high-offset and low-offset. And microprocessor (ATmega128) and D/A converter with 8 bits resolution are used in the proposed driver so that LED's illumination can be remotely controlled by serial communication on the spot or by key input. In the results of performance tests, we confirmed that the proposed control method is superior to the conventional control method using op-amps.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.8
• /
• pp.1130-1139
• /
• 2012

This paper proposes a LED lighting system using integrated power system composed of bridgeless PFC, LLC DC-DC transformer, and dimmable constant current LED driver module. The proposed LED lighting system features high efficiency, high power factor, and dimming capability. In order to verify the validity of the proposed system, the 2kW prototype system was built and tested. From the experimental results, it was confirmed that the maximun efficiency of 92.6% and maximum power factor of 99.7% can be achieved.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.8
• /
• pp.1-6
• /
• 2015

In this paper, we propose the LED(Light-Emitting-Diode) emergency lighting in a tunnel by using the thermoelectric devices. To achieve high generated power, thermoelectric device should be have high Seebeck coefficient and small contact area. Also, we reveal that a moderate heatsink required for high generated power. From the waste heat of LED tunnel lighting module (25W), the generated power was 0.062W by thermoelectric device, and it could illuminate for 1hour after charge the battery of emergency lighting during about 101hours.

• Korean Journal of Optics and Photonics
• /
• v.18 no.2
• /
• pp.111-116
• /
• 2007

A high power LED which is being used in many illumination applications as a new light source was simulated for its physical structure and then its optical properties were analyzed. To obtain accurate results from the designed LED model, properties of the die chip and reflector cup were varied. As a result, a high power LED model which has a radiation pattern of a Lambertian with its viewing angle of approximately $140^{\circ}$ and total included angle of $160^{\circ}$ was designed.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.1379-1384
• /
• 2009

High power light emitting diode(LEDs), a strong candidate for the next generation general illumination applications are of interest. With major advantages of power saving, increased life expectancy and faster response time over traditional incandescent bulb, the LEDs are rapidly taking over many applications such as LCD backlighting, traffic light, automotive lighting, signage, etc. The increased electrical currents used to drive the LEDs have focused more attention on the thermal management because the efficiency and reliability of the solid-state lighting devices strongly depend on successful thermal management. There exist some problems that are caused by heat generation in the LED package, such as wire breakage, yellowing of epoxy resin, lifted chip caused by reflow of thermal paste chip attach and interfacial separation between LED package and silicon resin. The goal of this study is to analyze high power LED thermal properties of using pulsating heat pipe.

• Proceedings of the KIPE Conference
• /
• 2012.11a
• /
• pp.95-96
• /
• 2012

본 논문에서는 조명용 LED 구동 장치를 위한 새로운 방식의 단일전력단을 갖는 LED 구동회로를 제안한다. 제안 회로는 임계모드에서 동작하는 부스트 컨버터를 역률 개선 회로로 사용하였고, LED 구동회로로 LLC 고주파 공진 회로를 채택하였다. 또한, 기존의 역률 개선 회로와 LED 구동회로의 2단 회로를 단일전력단을 갖는 회로로 구성함으로 고역률, 고효율, 경량 및 소형의 LED 구동회로를 구성하였다. 본 논문에서는 제안한 회로의 동작 원리를 설명하였고, 시뮬레이션과 실험을 통하여 제안 회로의 타당성을 입증하였다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.4
• /
• pp.320-327
• /
• 2016

We propose a multi-channel current-balancing single switch light-emitting diode (LED) driver for a 3D TV. Conventional LED drivers require non-isolated DC/DC converters as many as the number of LED channels, whereas the proposed LED driver needs only one power switch and several balancing capacitors instead of expensive non-isolated DC/DC converters. Therefore, the proposed driver features a simple structure with low cost and high efficiency. In particular, because its power switch can be turned off under the zero-current switching condition, the proposed driver has desirable advantages, such as improved electromagnetic interference characteristics and high efficiency. Moreover, it only uses a small number of DC blocking capacitors with no additional active devices for the current balancing of multi-channel LEDs. Therefore, the proposed driver exhibits high reliability and cost effectiveness. To confirm the validity of the proposed driver, we perform a theoretical analysis and present design considerations and experimental results obtained from a prototype that is applicable to a 46" LED TV.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.7
• /
• pp.89-95
• /
• 2014

An LED lighting which adjusted brightness according to the surround ambient implemented using PWM technology and power devices. To measure the brightness of surround ambient a CdS sensor was used. A control board for the generation of the PWM signal was made using a MCU and duty ratio was controlled according to light intensity of surround ambient of the system. To drive the LED lamps which require high-voltage and high-current power devices were used for switching the DC power supply. Measurement results show that the IGBT is excellent as only lineality but the PowerBJT is more good to consider to efficiency and cost.

• Journal of Applied Reliability
• /
• v.12 no.3
• /
• pp.177-186
• /
• 2012

This paper presents a comparison of the failure mechanism for high power converted white LEDs(3W) with the commercially available YAG:Ce and silicate phosphor. We carry out the normal aging life test for 10,000 hours, the high temperature aging test for 8,000 hours, the high temperature and humidity aging test for 8,000 hours and the current aging testing for 5,000 hours. The optical and electrical parameters of LEDs were monitored, such as lumen, correlated color temperature (CCT), chromaticity coordinates(x, y), thermal resistance, I -V curve and spectrum intensity. The stress induced a luminous flux decay on LED in all experiments and causes a failure. So we try to find out what's a main failure mechanism for a high power LED.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.7
• /
• pp.473-479
• /
• 2015

Hybrid supercapacitors with high power density and long cycle life are widely used for emergency power source of LED emergency luminaires. In this paper, we designed and fabricated a hybrid capacitor cell and a module for the LED emergency luminaires. Using hybrid supercapacitor cells (1,000 F, 2.8 V), we designed a module in a 10-year warranty considering aging and ESR. Considering the ESR and efficiency has been designed to module with 1,000 F 5.6 V design results in 2 series and 2 parallel combination. Module was used to confirm that the operation 77.5 minutes at room temperature, discharge LED emergency luminaires with 2 W. As a LED emergency luminaires of emergency power supply that we can support more than 10 years of life was confirmed the applicability of hybrid supercapacitor.