• Journal of Korean Society for Atmospheric Environment
• /
• v.31 no.5
• /
• pp.449-460
• /
• 2015

Carbonaceous aerosol is generally classified into OC (organic carbon) and EC (elemental carbon) by thermal optical analysis. Both NIOSH (National institute of occupational safety and health) with high temperature (HighT) and IMPROVE-A (Interagency monitoring of protected visual environments) with low temperature (LowT) protocols are widely used. In this study, both protocols were applied for ambient $PM_{2.5}$ samples (Daejeon, Korea) in order to underpin differences in OC and EC measurements. An excellent agreement between NIOSH and IMPROVE-A protocol was observed for TC (total carbon). However, significant differences between OC and EC appeared and the differences were larger for EC than OC. The main differences between two protocols are temperature profile and charring correction method. For the same charring correction method, HighT_OC was 10% higher than LowT_ OC, while HighT_EC was 15% and 33% lower than LowT_EC for TOT (thermal-optical transmittance) and TOR (thermal-optical reflectance), respectively. This difference may be caused by the temperature of OC4 in He step and possibly difference in POC (pryorilized OC) formation. For the same temperature profile, OC by TOT was about 26% higher than that by TOR. In contrast, EC by TOT was about 50% lower than that by TOR. POC was also dependent on both temperature profile and the charring correction method, showing much distinctive differences for the charring correction method (i.e., POC by TOT to POC by TOR ratio is about 2). This difference might be caused by different characteristics between transmittance and reflectance for monitoring POC formation within filters. Results from this study showed that OC and EC depends on applied analysis protocol as shown other studies. Because of the nature of the thermal optical analysis, it may not be possible to have an absolute standard analysis protocol that is applicable for any ambient $PM_{2.5}$. Nevertheless, in order to provide consistent measurement results for scientists and policy makers, future studies should focus on developing a harmonized standard analysis protocol that is suitable for a specific air domain and minimizes variations in OC and EC measurement results. In addition, future elaborate studies are required to find and understand the causes of the differences.

• Korean Journal of Materials Research
• /
• v.9 no.12
• /
• pp.1245-1251
• /
• 1999

Phase-change optical disk very rapid recording, high densification of data, resulting in high feedback rate and good C/N(carrier to noise) ratio of a feedback signal. However, repetitive thermal energy may cause the deformation of a disk or the lowering of an eliminability and a cyclability of the recording. The lowering of the cyclability can be reduced by insertion of thin layer of ZnS-$SiO_2$ dielectric thin film in appropriate disk structure between the upper and lower part of the recording film. Using the Taguchi method, optimum conditions satisfying both the optimized quality characteristic values and the scattering values for film formation were found to be the target R.F. power of 200W, the substrate R.F. power of 20W, the Ar pressure of 6mTorr, and the electrode distance of 6cm. From the refractive index data, the existence of the strong interaction between the electrode distance and Ar pressure was confirmed, and so was the large effect of the electrode distance on transmittance. According to the analysis of TEM and XRD, the closer the electrode distance was, the finer was the grain size due to the high deposition rate. However, the closer electrode distance brought the negative effect on the morphology of the film and caused the reduction of transmittance. AFM and SEM analyses showed that the closer the electrode distance was, the worse was the morphology due to the high rate of the deposition. Under optimum condition, the deposited thin film showed a good morphology and dense microstructure with less defects.

• Horticultural Science & Technology
• /
• v.32 no.1
• /
• pp.10-17
• /
• 2014

This study was conducted to elucidate the relationship between light and coloring and to obtain basic results for promoting redness expression in 'Kalle' (Pyrus communis L.) pear skin. It was investigated in location of anthocyanin layer by microscopic observation and differences in skin color expression of 'Kalle' bagged with paper bag which has different light transmittance rate and inside temperature. However, there was no anthocyanin layer in the brown skin and golden yellow color, anthocyanin layer was distributed in epidermins or hyperdermis of red skin pear and apple. Dark red colored 'Kalle' had more anthocyanin content, $29.8mg{\cdot}100g^{-1}$ FW than light red colored apple 'Hongro'. Light transmittance rate of physical characteristics used paper bags was the highest in white paper bag, 42.2% and it also had more light quantity, $8.9{\mu}mol$ than any other tested paper bags in specific wave length 650-655 nm. The maximum temperature of inner bag was higher about $3^{\circ}C$ in yellow paper bag. The red coloration and anthocyanin contents in no bagged fruits were higher than in any other bagged fruit. However, red color expression among the bagged fruits was higher in white paper bag than in double layered black paper bag and yellow paper bag. Also, chromaticity value seemd to be a good index to explain variation of fruit skin color, because anthocyanin content and chromaticity value were higher. Based on these results, it is desirable to cultivate 'Kalle' without bag for stable redness expression but bagging is essential for decreasing damage by insect in Korea. Further examination to find suitable time of removing paperbag for redness expression and decreasing insect damage. In addition, it is required to develop paperbag whose transmittance rate is high in specific light wavelength or temperature of inner bags is low. Additional key words: anthocyanin, bagging, chromaticity value, light transmittance, Pyrus communis L.

• Current Photovoltaic Research
• /
• v.7 no.4
• /
• pp.97-102
• /
• 2019

Bifacial and semitransparent hydrogenated amorphous silicon (a-Si:H) thin-film solar cells in p-i-n configuration were prepared with front and rear transparent conducting oxide (TCO) electrodes using plasma-enhanced chemical vapor deposition method. Fluorine-doped tin oxide and tin-doped indium oxide films were used as front and rear TCO contacts, respectively. Film thickness of intrinsic a-Si:H absorber layers were controlled from 150 nm to 450 nm by changing deposition time. The dependence of performance characteristics of solar cells on the front and rear illumination direction were investigated. For front illumination, gradual increase in the short-circuit current density (J_SC) from 10.59 mA/㎠ to 14.19 mA/㎠ was obtained, whereas slight decreases from 0.83 V to 0.81 V for the open-circuit voltage (V_OC) and from 68.43% to 65.75% for fill factor (FF) were observed. The average optical transmittance in the wavelength region of 380 ~ 780 nm of the solar cells decreased gradually from 22.76% to 15.67% as the absorber thickness was changed from 150 nm to 450 nm. In case of the solar cells under rear illumination condition, the J_SC increased from 10.81 to 12.64 mA/㎠ and the FF deceased from 66.63% to 61.85%, while the V_OC values were maintained at 0.80 V with increasing the absorber thickness from 150 nm to 450 nm. By optimizing the deposition parameters, a high-quality bifacial and semitransparent a-Si:H solar cell with 350 nm-thick i-a-Si:H absorber layer exhibited the conversion efficiencies of 7.69% for front illumination and 6.40% for rear illumination, and average visible optical transmittance of 17.20%.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.10
• /
• pp.771-776
• /
• 2017

The cover glass of mobile displays and photovoltaic cells needs a functional coating, such as an anti-reflection and self-cleaning coating. Numerous studies have been conducted on the engineering application of biomimetic functional surfaces, such as moth eye and lotus leaf Anti-reflection coantings of silica nanoparticles could enhance the light transmittance. $TiO_2$ photocatalyst coatings have been applied to self-cleaning functional films. In this study, transparent hydrophobic anti-reflective coatings consisting of thin layers of $SiO_2/TiO_2$ nanoparticles were fabricated on a slide glass substrate by the sol-gel process and dip-coating process. The dependence of the surface morphology of the functional coatings was investigated by the atomic force microscopy (AFM), contact angle measurement, and UV-visible spectroscopy. It was found that the coating of $TiO_2$ nanoparticles exhibited a high average transmittance comparable to that of the bare slide glass substrate in the visible light range. The bi-layered functional coating of 7 nm $SiO_2$/7nm $TiO_2$ nanoparticles exhibits a transparent hydrophobic surface with a contact angle of $110^{\circ}$ and an improvement of the average transmittance of 2.3% compared to the bare slide glass substrate in the visible light range.

• Land and Housing Review
• /
• v.10 no.3
• /
• pp.23-32
• /
• 2019

Vacuum Insulation Panel(VIP) has the lowest thermal conductivity among present insulations. It is composed of envelope, core material and getter. Aluminum film is usually used as the envelope of VIP, and it is important component to decide the useful life of VIP. In this research, the thermophysical properties of incombustible fiber glass core VIP were investigated with the possibility of its architectural applications. The results of this research can be summarized as follows: 1) The thermal conductivity of 20mm-thick fiber glass core VIP is resulted as 0.00177W/m·K, which means that 20mm-thick VIP can meet all the reinforced insulation guideline and it can be used in any envelope of any region in Korea. 2) As a result of the test of incombustion and gas toxicity, fiber glass core VIP was suitable for incombustible material. 3) As the test result for the long term thermal conductivity, fiber glass core VIP was found out that it would keep above 10 times insulating performance than polystyrene foam and glass fiber. 4) To meet the thermal transmittance of 0.12W/㎡K, limited-combustible insulation of expanded polystyrene foam and phenolic foam should be used respectively as thick as above 280mm and 170mm, incombustible VIP can meet the same insulation level with 20mm thickness. 5) The price competitiveness of incombustible VIP to meet the thermal transmittance of 0.12W/㎡·K was about 1,500won/㎡ higher than that of phenolic foam.

• Korean Journal of Optics and Photonics
• /
• v.26 no.2
• /
• pp.73-82
• /
• 2015

This work demonstrates the indoor SI-traceable calibration of a transmissometer with a 75-m baseline for the measurement of visibility in MOR (Meteorological Optical Range). The calibration is performed using a set of neutral density (ND) filters (OD 0.1-2.5) and a set of high-transmission quartz glass plates (a bare quartz glass plate and antireflective-coated quartz glass plates), the collection consisting of 20 artifacts in total. The luminous transmittance values of the reference artifacts had been calibrated traceable to the KRISS spectral transmittance scale, which ranges from 0.2 % to 99.5 %. The transmissometer to be calibrated typically consists of a loosely collimated light source based on a white LED (CCT ~5000 K) and a luminous intensity detector with a CIE 1924 V(${\lambda}$) spectral response. As a result of calibration, we obtained the MOR error and its uncertainty for the transmissometer in 20 m - 40 km of MOR. Based on the results, we investigated the applicability of the calibration method and the conformity of the transmissometer to the ICAO's (International Civil Aviation Organization) accuracy requirement for meteorological visibility measurement. We expect that this work will establish the standard procedure for the SI-traceable calibration of a transmissometer.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.3
• /
• pp.497-504
• /
• 2019

We fabricated $HfO_2$ thin films using RF magnetron sputtering method, and investigated structural and optical properties of $HfO_2$ thin films with RTA temperatures in $N_2$ ambient. $HfO_2$ thin films exhibited polycrystalline structure regardless of annealing process, FWHM of M (-111) showed reduction trend. The surface roughness showed the smallest of 3.454 nm at a annealing temperature of $600^{\circ}C$ in result of AFM. All $HfO_2$ thin films showed the transmittance of about 80% in visible light range. By fitting the refractive index from the transmittance and reflectance to the Sellmeir dispersion relation, we can predict the refractive index of the $HfO_2$ thin film according to the wavelength. The $HfO_2$ thin film annealed at $600^{\circ}C$ exhibited a high refractive index of 2.0223 (${\lambda}=632nm$) and an excellent packing factor of 0.963.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.1
• /
• pp.25-30
• /
• 2020

Oxide (SiO₂)/Metal(Ag)/Oxide(SiO₂, ITO, ZnO) multilayer films were fabricated using a magnetron sputtering technique at room temperature on Si (p-type, 100) and a glass substrate. The electrical and optical properties of the asymmetric multilayer films depended on the thickness of the mid-layer film and the type of oxide in the bottom layer. As the metal layer becomes thicker, the sheet resistance decreases. However, the transmittance decreases when the metal layer exceeds a threshold thickness of approximately 10~12 nm. In addition, the sheet resistance and transmittance change according to the type of oxide in the bottom layer. If the oxide has a large resistivity, the overall sheet resistance increases. In addition, the anti-reflection effect changes according to the refractive index of the oxide material. The optical and electrical properties of multilayer films were investigated using an ultraviolet visible (UV-Vis) spectrophotometer and a 4-point probe, respectively. The optimum structure is SiO₂ (30 nm)/Ag (10 nm)/ZnO (30 nm) multilayer, with the highest FOM value of 7.7×10^-3 Ω^-1.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.187-187
• /
• 2015

The past thirty years have seen increasingly rapid advances in the field of Indium Tin Oxide (ITO) transparent thin film.[1] However, a major problem with this ITO thin film application is high cost compared with other transparent thin film materials.[2] So far, in order to overcome this disadvantage, we show a transparent ITO/Ag/i-ZnO multilayer thin film electrode can be the solution. In comparison with using amount of ITO as a transparent conducting material, intrinsic-Zinc-Oxide (i-ZnO) based on ITO/Ag/i-ZnO multilayer thin film showed cost-effective and it has not only highly transparent but also conductive properties. The aim of this research has therefore been to try and establish how ITO/Ag/i-ZnO multilayer thin film would be more effective than ITO thin film. Herein, we report ITO/Ag/i-ZnO multilayer thin film properties by using optical spectroscopic method and measuring sheet resistance. At a certain total thickness of thin film, sheet resistance of ITO/Ag/i-ZnO multilayer was drastically decreased than ITO layer approximately $40{\Omega}/{\square}$ at same visible light transmittance.(minimal point $5.2{\Omega}/{\square}$). Tendency, which shows lowly sheet resistive in a certain transmittance, has been observed, hence, it should be suitable for transparent electrode device.